电镀废水的铬污染特征及调控

以广东省潮州市彩塘不锈钢电镀区的水体为例,研究了电镀废水、底泥的Cr分布特征和基本特性,并针对废水基本特性,采用FeSO4进行调控,探讨如何将Cr6+转化Cr3+以及除去废水中Cr的途径。电镀废水中的总Cr和Cr6+分别为57.3mg/L、42.4mg/L,远远超过了电镀废水排放标准37、83倍,导致河流水体Cr6+超过环境质量标准。电镀废水具有低pH值和高电导率。电镀区底泥Cr大大超过背景值,底泥中的Cr残渣态含量最高,其次是氧化态、还原态,可溶态和碳酸盐态含量低,说明了底泥存在潜在危害性。FeSO4能有效地将Cr6+还原为Cr3+,Fe2+/Cr6+摩尔比为4具有很好转化效率,还原充分后将pH值调至9,对Cr3+具有最好的沉淀效果,通过该途径有效除去废水的Cr。     

毛细柱气相色谱法测定天然水中痕量铍、铝、铬

介绍一个用毛细柱气相色谱法同时测定铍、铝、铬酌新方法。在pH为5.6的醋酸-醋酸钠缓冲溶液中,铍、铝、铬与三氟乙酰丙酮生成挥发性和热稳定性的金属整合物。可萃取至苯中,注射至熔融石英WCOT OV—101柱上,在140℃分离测定,用电子捕获检测器检测。铍、铝、铬的回收率分别为83—103％,88—105％,90—103％。变异系数分别为6.5％,6.5％,2.0％。可用于天然水中亚ppb级铍、铝、铬的分析。测定了海水、河口水、矿泉水、雪水等样品。     

连续流动分析法测定水中的CODCr

采用连续流动分析技术对环境水样中的CODCr进行大批量快速测定 ,与国标法 (重铬酸钾法 )有可比性 ,分析结果具有良好的准确性和重现性 ,方法检出限 1 3,对标准样品分析的准确度在 98%以上 ,变异系数在 0 2 1%～ 1 0 0 %之间 ,实际水样的检测结果与重铬酸钾法的相对偏差为 0 4 %～ 1 4 % ,环境水样和工业废水的加标回收率为 93%～10 1%。     

电化学法直接快速测定COD初步研究

对一种全新的方法—电化学法测定COD进行了初步研究。制备出析氧超电位很大的铂基α PbO2 和 β PbO2 双镀层电极 ,并用以电解产生羟基自由基直接氧化废水中有机物。在本研究确定的条件下 ,COD标液在 0～ 30 0mg L呈良好的线性关系 ,一次测定仅需 30s。     

Experimental study on Cr(Ⅵ) reduction by Pseudomonas aeruginosa

Investigation on Cr(Ⅵ) reduction was conducted using Pseudomonas aeruginosa. The study demonstrated that the Cr(Ⅵ) can be effectively reduced to Cr(Ⅲ) by Pseudomonas aeruginosa. The effects of the factors affecting Cr(Ⅵ) reduction rate including carbon source type, pH, initial Cr(Ⅵ) concentration and amount of cells inoculum were thoroughly studied. Malate was found to yield maximum biotransformation, followed by succinate and glucose, with the reduction rate of 60.86%, 43.76% and 28.86% respectively. The optimum pH for Cr(Ⅵ) reduction was 7.0, with reduction efficiency of 61.71% being achieved. With the increase of initial Cr(Ⅵ) concentration, the rate of Cr(Ⅵ) reduction decreased. The reduction was inhibited strongly when the initial Cr(Ⅵ) concentration increased to 157 mg/L. As the amount of cells inoculum increased, the rate of Cr(Ⅵ) reduction also increased. The mechanism of Cr(Ⅵ) reduction and final products were also analysed. The results suggested that the soluble enzymes appear to be responsible for Cr(Ⅵ) reduction by Pseudomonas aeruginosa, and the reduced Cr(Ⅲ) was not precipitated in the form of Cr(OH)3.     

Flower-, wire-, and sheet-like MnO2-deposited diatomites: Highly efficient absorbents for the removal of Cr(VI)

Flower-, wire-, and sheet-like MnO₂-deposited diatomites have been prepared using a hydrothermal method with Mn(Ac)₂, KMnO₄ and/or MnSO₄ as Mn source and diatomite as support. Physical properties of the materials were characterized by means of numerous analytical techniques, and their behaviors in the adsorption of chromium(VI) were evaluated. It is shown that the MnO₂-deposited diatomite samples with different morphologies possessed high surface areas and abundant surface hydroxyl groups (especially the wire-like MnO₂/diatomite sample). Thewire-like MnO₂/diatomite sample showed the best performance in the removal of Cr(VI), giving the maximum Cr(VI) adsorption capacity of 101 mg/g.     

粉煤灰对含铬废水的吸附研究

通过静态吸附实验,研究原状粉煤灰与粉煤灰滤料对Cr(Ⅵ)的吸附效果的影响,并通过正交实验进行实验结果对比。实验确定粉煤灰滤料的吸附平衡时间为90 min,在pH为3的条件下适于进行吸附实验;同时,粉煤灰滤料的吸附性能优于原状粉煤灰,六价铬溶液的初始浓度、滤料的投加量以及温度的改变对吸附性能具有显著影响,且粉煤灰滤料吸附时所受影响更为明显。     

改性污泥活性炭吸附废水中Cr(Ⅵ)的性能研究

以污水处理厂剩余污泥为原料,1.0 mol/L KOH做活化改性剂,制备污泥活性炭,探讨不同条件下其对废水中Cr(VI)的吸附性能.结果表明,污泥活性炭对Cr(VI)吸附的最佳条件为:pH为2,温度为25℃,污泥活性炭投加量为5 g/L,吸附时间为40 min.此条件下,废水中Cr(VI)的去除率可达99%以上.动力学分析表明,污泥活性炭对Cr(VI)废水的吸附符合准二级动力学方程与Langmuir等温式.     

污染场地六价铬的还原和微生物稳定化研究

通过采集苏州某化工原址场地铬污染土壤,首先加入石硫合剂使大部分六价铬[Cr(Ⅵ)]还原,再加入营养液促进土著微生物大量生长,利用微生物还原稳定化土壤中的铬.培养60 d后,通过毒性浸出、土壤中剩余Cr(Ⅵ)测定等实验确定稳定化效果,结果表明,加入5%营养液培养后,土壤毒性浸出液中Cr(Ⅵ)浓度由原来的8.26 mg·L-1降低到0.26 mg·L-1,降低了96.8%,总铬浓度由原来14.66 mg·L-1降低到0.63 mg·L-1,降低了95.7%.另外,通过高锰酸钾氧化实验和灭菌实验确定稳定化的持久性,高锰酸钾氧化后,仅通过还原处理的土壤浸出液中Cr(Ⅵ)由8.26 mg·L-1增加到14.68 mg·L-1,而经稳定化后的土壤浸出液中Cr(Ⅵ)降低到2.68 mg·L-1.稳定化后的土壤样品经紫外灭菌,发现微生物消亡后,对稳定化效果没有显著影响.因此,初步证明了高浓度高毒性的Cr(Ⅵ)污染土壤经初步还原后再经微生物稳定化治理是可行的,为Cr(Ⅵ)污染场地治理提供了一种高效低成本的修复技术.     

Flower-, wire-, and sheet-like MnO2-deposited diatomites: Highly efficient absorbents for the removal of Cr(VI)

Flower-, wire-, and sheet-like MnO₂-deposited diatomites have been prepared using a hydrothermal method with Mn(Ac)₂, KMnO₄ and/or MnSO₄ as Mn source and diatomite as support. Physical properties of the materials were characterized by means of numerous analytical techniques, and their behaviors in the adsorption of chromium(VI) were evaluated. It is shown that the MnO₂-deposited diatomite samples with different morphologies possessed high surface areas and abundant surface hydroxyl groups (especially the wire-like MnO₂/diatomite sample). The wire-like MnO₂/diatomite sample showed the best performance in the removal of Cr(VI), giving the maximum Cr(VI) adsorption capacity of 101 mg/g.