探地雷达—电法—化探技术在地下排污管网探测工程中的应用

介绍探地雷达－电法化探技术的基本原理及应用于齐鲁石化公司地下排污管线进行测漏的工程实例。     

USING CURVE NUMBERS TO DETERMINE BASELINE VALUES OF GREEN-AMPT EFFECTIVE HYDRAULIC CONDUCTIVITIES1

ABSTRACT: Since the trend in infiltration modeling is currently toward process-based approaches such as the Green-Ampt equation, more emphasis is being placed on methods of determining appropriate parameters for this approach. The SCS curve number method is an accepted and commonly used empirical approach for estimating surface runoff, and is based on numerous data from a variety of sources. The time and expense of calibrating process-based infiltration parameters to measured data are often prohibitive. This study uses curve number predictions of runoff to develop equations to estimate the “baseline” hydraulic conductivities (K_b) for use in the Green-Ampt equation. Curve number predictions of runoff were made for 43 soils. K_b values in the Water Erosion Prediction Project (WEPP) model were then calibrated so that the annual runoff predicted by WEPP was equal to the curve number predictions. These calibrated values were used to derive an equation that estimated K_b based on the percent sand, percent clay, and cation exchange capacity of the soil. Estimated values of K_b from this equation compared favorably with measured values and values calibrated to measured natural runoff plot data. WEPP predictions of runoff using both optimized and estimated values of K_b were compared to curve number predictions of runoff and the measured values. The WEPP predictions using the optimized values of K_b were the best in terms of both average error and model efficiency. WEPP predictions using estimated values of K_b were shown to be superior to predictions obtained from the curve number method. The runoff predictions all tended to be biased high for small events and low for larger events when compared to the measured data. Confidence intervals for runoff predictions on both an annual and event basis were also developed for the WEPP model.     

行道树对城市道路交通环境的响应研究

以南方常见的8种城市行道树作为研究对象,并以各自在远离城市道路交通环境生长的树种作为对照,对行道树及其对照样品叶片和树皮的重金属铅和镉、电导率、pH值、叶片伤斑率及叶片表皮结构气孔数等进行测定,以探讨不同树种对交通环境的响应.结果表明,与对照树种比较,行道树叶片和树皮能累积城市道路交通环境中的重金属铅和镉,其电导率和叶片的伤斑率增加,pH值下降.叶片气孔数的变化随树种不同有所差别,如阴香〔Cinnamomumbur-manii(Nees)〕等的叶片气孔数比对照少,而细叶榕(FicusmicrocarpaL.)等比对照多.根据行道树的生长状况及净化重金属的能力,8种供试植物中,白兰(MicheliaalbaDC.)和垂叶榕(FicusbenjaminaL.)最适合选作行道树,而阴香因其在交通环境中生长不良,净化效益差,不宜选作交通密集区的行道树种.图3表3参17     

离子当量电导率对饮用水评价应用研究

根据科尔劳施离子独立运动定律(离子在溶液中的导电行为)研究了离子当量电导率对饮用水环境评价的可行性。同一条件下各水体当量计算电导准确地反映各种污染物的总量,并按照一定数学关系制定评价标准。文章通过对淮北市9口饮用水井的分析,结果满意。     

电导率的测定与质量监督工作

电导率、矿化度和总硬度密切相关。由此电导率的测定值可用来检验矿化度和总硬度测定值的准确性,加强质量控制,本文指出,电导率的测定应作为水样的首测项目。     

干湿循环与垃圾渗滤液耦合作用下GCL防渗性能

开展膨胀指数和渗透系数测定试验,研究干湿循环与垃圾渗滤液渗透耦合作用下膨润土的膨胀性能和土工合成黏土衬垫（GCL）防渗性能变化规律.结果表明,干湿循环与垃圾渗滤液渗透耦合作用对膨润土的膨胀性能和GCL的防渗性能具有显著负面影响：在7次干湿循环后,垃圾渗滤液饱和的膨润土的膨胀指数从20mL/2g降低至7.5mL/2g,GCL的渗透系数从1.65×10^-11m/s增加到1.89×10^-7m/s.膨胀指数下降和渗透系数升高的根本原因是膨润土渗透膨胀性能的丧失.单纯的垃圾渗滤液渗透不会改变GCL的渗透系数.将有效应力从20kPa升高至150kPa,可以促使GCL的渗透系数降低4个数量级,满足填埋场防渗要求（< 5.0x10^-11m/s）.     

Gd2O3-NiO 共掺对钇稳定氧化锆材料热物理性能的影响

目的研究Gd_2O_3-NiO共掺对钇稳定氧化锆材料热物理性能的影响。方法采用高温固相反应法制得Gd_2O_3-NiO共掺YSZ陶瓷材料。分别利用XRD、扫描电镜观察、激光导热仪、傅立叶红外光谱仪对陶瓷材料的晶体结构、微观结构、热扩散系数及红外透过率进行表征,并对其热导率进行分析。结果 Gd_2O_3-NiO共掺YSZ后,陶瓷材料单斜相含量减少,室温至1300℃的热导率相比YSZ降低,在2.5~5μm波长范围内红外透过率降低。结论 Gd_2O_3-NiO共掺对YSZ陶瓷材料热导率的影响机理为掺杂Gd_2O_3和NiO导致YSZ中单斜相(M)、四方相(T)和立方相(C)含量发生变化,同时YSZ晶格发生畸变。对YSZ辐射传热的影响机理为通过在YSZ中掺杂过渡金属元素Ni使陶瓷材料吸收特定波长的光,进而有效地降低在2.5~5μm短波长的红外透过率,降低其高温下的红外辐射传热。     

ELPI 测定环境空气 PM2．5的现场比对研究

采用ELPI自动监测方法与手工采样－重量法对环境空气PM2．5监测进行现场比对研究,按照两种方法数据的相对偏差来评价ELPI方法的数据质量。实验结果表明,两种方法数据的相对偏差范围为－12．9％～17．4％,加权平均值为3．0％;相对偏差的绝对值范围为1．1％～17．4％,平均值为9．3％。 ELPI法的数据质量总体较好,方法的准确度尚可。只是随着空气PM2．5浓度测定值的升高,ELPI法与重量法相对偏差的绝对值显著减小,可见,在低浓度下,ELPI法的数据质量相对较差,此时方法的准确度有待进一步验证、提高。     

Status quo of e-waste management in mainland China

In China, the use and obsolescence of both electronic and electrical equipment have increased rapidly in recent years. China has also begun to take measures to cope with this problem since it began experiencing a rapid process of industrialization and urbanization in the 1990s. In this paper, the profile of the electrical and electronic waste (e-waste) problem in China is depicted from such aspects as domestic e-waste and imported e-waste, along with their recycling systems, policies, and regulations. Based on statistics of the consumption of major household appliances and personal computers, a forecast is made of the numbers of obsolete major household appliances and personal computers. The results show that currently the number of electrical and electronic products in use in China is tremendous. An investigation on household appliances and personal computers in Beijing was made to assess the use and obsolescence of these products. Also, the legal issues relating to e-waste in China are summarized, and these will be the juristic foundation for the solution of e-waste problems.     

两步法制备导电聚吡咯薄膜研究

在陶瓷基底上,先用化学方法,再用电化学方法两步聚合制备导电聚吡咯（PPy）薄膜。研究了施加电流和聚合时间对PPy导电薄膜电导率的影响,对比分析了两步聚合法和化学方法对PPy导电薄膜组织的影响,并对两步法在陶瓷和Al2O3基底上制备PPy导电薄膜的微观形貌进行了观察分析。结果表明,两步聚合方法制备的PPy导电薄膜的电导率随着施加电流的增大和聚合时间的增长而逐渐提高;两步法制备PPy导电薄膜的组织较仅用化学方法制备PPy导电薄膜的组织要致密连续;陶瓷基底上PPy薄膜较均匀,而Al2O3基底上PPy薄膜较疏松且不连续。