火化过程中二噁英类污染物减排技术研究

为减少火化过程中二噁英类污染物的排放,研究了"热交换器 布袋除尘器 活性炭纤维毡"三级组合对火化遗体烟气中二噁英类污染物的去除效果.利用急冷技术将二次燃烧室排出的火化烟气温度降到90～130℃.实验表明,布袋除尘器去除火化烟气中二噁英类污染物的效率为57.4%;布袋除尘器分别与厚度为5、15 mm的活性炭纤维毡组合去除火化烟气中二噁英类污染物的效率分别为64.0%和89.2%.     

Estimating fugitive dust emission rates using an environmental boundary layer wind tunnel

Emissions from fugitive dust due to erosion of “natural” wind-blown surfaces are an increasingly important part of PM₁₀ (particulate matter with sizes of 10 μm aerodynamic diameter) emission inventories. These inventories are particularly important to State Implementation Plans (SIP), the plan required for each state to file with the Federal government indicating how they will comply with the Federal Clean Air Act (FCAA). However, techniques for determining the fugitive dust contribution to over all PM₁₀ emissions are still in their developmental stages. In the past, the methods have included field monitoring stations, specialized field studies and field wind-tunnel studies. The measurements made in this paper allow for systematic determination of PM₁₀ emission rates through the use of an environmental boundary layer wind tunnel in the laboratory. Near surface steady-state concentration profiles and velocity profiles are obtained in order to use a control volume approach to estimate emission rates. This methodology is applied to soils retrieved from the nation's single largest PM₁₀ source, Owens (dry) Lake in California, to estimate emission rates during active storm periods. The estimated emission rates are comparable to those obtained from field studies and lend to the validity of this method for determining fugitive dust emission rates.     

Characterizing the source/sink behavior of double-layer building materials

A model is developed to predict the rate of mass transfer between a double-layer material and indoor air. The model allows non-uniform initial material-phase concentrations in each of the two layers and a transient influent gas-phase concentration to be considered. This model builds on a recently validated single-layer model and should prove useful in predicting the behavior of double-layer material assemblies. Many indoor furnishings and building structures are comprised of layers of different material. The approach taken here represents a first step in the development of a more generally applicable multi-layer model. An analytical solution to the double-layer model is obtained and a parametric analysis is performed illustrating the behavior of the model as a function of the primary model parameters. The paper concludes by examining the potential use of thin diffusion barriers to reduce material emission rates and a hypothetical example of emissions from an adhesive that is part of an adhesive/material assembly.     

Gas-phase organics in environmental tobacco smoke: 2. Exposure-relevant emission factors and indirect exposures from habitual smoking

Sorption of emitted gas-phase organic compounds onto material surfaces affects environmental tobacco smoke (ETS) composition and exposures indoors. We have introduced a new metric, the exposure relevant emission factor (EREF) that accounts for sorptive uptake and reemission to give the mass of individual ETS constituents available for exposure over a day in which smoking occurs. This paper describes month-long experiments to investigate sorption effects on EREFs and potential ETS exposures under habitual smoking conditions. Cigarettes were smoked in a 50-m³ furnished room over a 3-h period 6–7 days per week, with continuous ventilation at 0.3, 0.6, or 2.1 h⁻¹. Organic gas concentrations were measured every few days over 4-h “smoking”, 10-h “post-smoking” and 10-h “background” periods. Concentration patterns of volatile ETS components including 1,3-butadiene, benzene and acrolein were similar to those calculated for a theoretical non-sorbing tracer, indicating limited sorption. Concentrations of ETS tracers, e.g. 3-ethenylpyridine (3-EP) and nicotine, and lower volatility toxic air contaminants including phenol, cresols, and naphthalene increased as experiments progressed, indicating mass accumulation on surfaces and higher desorption rates. Daily patterns stabilized after week 2, yielding a steady daily cycle of ETS concentrations associated with habitual smoking. EREFs for sorbing compounds were higher under steady cycle versus single-day smoking conditions by 50% for 3-EP, and by 2–3 times for nicotine, phenol, cresols, naphthalene, and methylnaphthalenes. Our results provide relevant information about potential indirect exposures from residual ETS (non-smoker enters room shortly after smoker finishes) and from reemission, and their importance relative to direct exposures (non-smoker present during smoking). Under the conditions examined, indirect exposures accounted for a larger fraction of total potential exposures for sorbing versus non-sorbing compounds, and at lower versus higher ventilation rates. Increasing ventilation can reduce indirect exposures to very low levels for non-sorbing ETS components, but indirect routes accounted for 50% of potential nicotine exposures during non-smoking periods at all ventilation rates.     

Emissions of organophosphate and brominated flame retardants from selected consumer products and building materials

The emissions of selected flame retardants were measured in 1- and 0.02-m³ emission test chambers and 0.001-m³ emission test cells. Four product groups were of interest: insulating materials, assembly foam, upholstery/mattresses, and electronics equipment. The experiments were performed under constant environmental conditions (23°C, 50% RH) using a fixed sample surface area and controlled air flow rates. Tris (2-chloro-isopropyl)phosphate (TCPP) was observed to be one of the most commonly emitted organophosphate flame retardants in polyurethane foam applications. Depending on the sample type, area-specific emission rates (SER_a) of TCPP varied between 20 ng m⁻² h⁻¹ and 140 μg m⁻² h⁻¹.The emissions from electronic devices were measured at 60°C to simulate operating conditions. Under these conditions, unit specific emission rates (SER_u) of organophosphates were determined to be 10–85 ng unit⁻¹ h⁻¹. Increasing the temperature increased the emission of several flame retardants by up to a factor of 500. The results presented in this paper indicate that emissions of several brominated and organophosphate flame retardants are measurable. Polybrominated diphenylethers exhibited an SER_a of between 0.2 and 6.6 ng m⁻² h⁻¹ and an SER_u of between 0.6 and 14.2 ng unit⁻¹ h⁻¹. Because of sink effects, i.e., sorption to chamber components, the emission test chambers and cells used in this study have limited utility for substances low vapour pressures, especially the highly brominated compounds; hexabromocyclododecane had an SER_a of between 0.1 and 29 ng m⁻² h⁻¹ and decabromodiphenylether was not detectable at all.     

Profiles of PAH emission from steel and iron industries

In order to characterize the polycyclic aromatic hydrocarbons (PAHs) emission from steel and iron industries, this study measured the stack emission of twelve steel and iron plants in southern Taiwan to construct a set of source fingerprints. The study sampled the emissions by the USEPA's sampling method 5 with the modification of Graseby for the gas and particulate phase PAH and, then, used Hewlett-Packard 5890 gas chromatograph equipped with mass spectrometer detector to analyze the samples. The steel and iron industries are classified into three categories on the basis of auxiliary energy source: Category I uses coal as fuel, Category II uses heavy oil as fuel and Category III uses electric arc furnace. The pollution source profiles are obtained by averaging the ratios of individual PAH concentrations to the total concentration of 21 PAHs and total particulate matter measured in this study. Results of the study show that low molecular weight PAHs are predominant in gas plus particulate phase for all three categories. For particulate phase PAHs, however, the contribution of large molecular weight compounds increases. Two-ring PAHs account for the majority of the mass, varying from 84% to 92% with an average of 89%. The mass fractions of 3-, 4-, 5-, 6-ring PAHs in Category I are found to be more than those of the other two categories. The mass of Category III is dominated by 7-ring PAHs. Large (or heavy) molecular weight PAHs (HMW PAHs) are carcinogenic. Over all categories, these compounds are less than 1% of the total-PAH mass on the average. The indicatory PAHs are benz[a]anthracene, benzo[k]fluoranthene, benzo[ghi]perylene for Category I, benzo[a]pyrene, acenaphthene, acenaphthylene for Category II and coronene, pyrene, benzo[b]chrycene for Category III. The indicatory PAHs among categories are very different. Thus, dividing steel and iron industry into categories by auxiliary fuel is to increase the precision of estimation by a receptor model. Average total-PAH emission factors for coal, heavy oil and electric arc furnace were 4050 μg/kg-coal, 5750 μg/l-oil, 2620 μg/kW h, respectively. Carcinogenic benzo[a]pyrene for gas plus particulate phase was 2.0 g/kg-coal, 2.4 μg/l-oil and 1.4 μg/kW h for Category I, II and III, respectively.     

Dioxin removal in “energy from waste plants” - comparison of air pollution control methods

The graph below shows the emitted dioxin - equivalents (Eadon) in grams per year in flue gas from municipal solid waste incinerators with various air pollution control methods for plants of capacity of 200 000 ton municipal solid waste (MSW) per year.

Full-size image (15K)

With optimized combustion and an effective air pollution control system the emissions of dioxins can be kept very low (concentrations below 0.1 ng/m³n).

With a very effective air pollution control system the total emission from all Swedish MSW-incinerators burning approximately 1.5 Mton/year will by 1990 be below 2 g/year - a drastic reduction from approximately 15 g today. As the total dioxin - equivalent emission to the environment in Sweden in the year 1987 was almost 500 g we see that municipal waste incineration really is on the way to solve their dioxin problem.     

Assessment of contribution of SO2 and NO2 from different sources in Jamshedpur region, India

Contribution of pollution from different types of sources in Jamshedpur, the steel city of India, has been estimated in winter 1993 using two approaches in order to delineate and prioritize air quality management strategies for the development of region in an environmental friendly manner. The first approach mainly aims at preparation of a comprehensive emission inventory and estimation of spatial distribution of pollution loads in terms of SO₂ and NO₂ from different types of industrial, domestic and vehicular sources in the region. The results indicate that industrial sources account for 77% and 68% of the total emissions of SO₂ and NO₂, respectively, in the region, whereas vehicular emissions contributed to about 28% of the total NO₂ emissions. In the second approach, contribution of these sources to ambient air quality levels to which the people are exposed to, was assessed through air pollution dispersion modelling. Ambient concentration levels of SO₂ and NO₂ have been predicted in winter season using the ISCST3 model. The analysis indicates that emissions from industrial sources are responsible for more than 50% of the total SO₂ and NO₂ concentration levels. Vehicular activities contributed to about 40% of NO₂ pollution and domestic fuel combustion contributed to about 38% of SO₂ pollution. Predicted 24-h concentrations were compared with measured concentrations at 11 ambient air monitoring stations and good agreement was noted between the two values. In-depth zone-wise analysis of the above indicates that for effective air quality management, industrial source emissions should be given highest priority, followed by vehicular and domestic sources in Jamshedpur region.     

葫芦岛锌厂二氧化硫排放总量的调查分析

葫芦岛锌厂是一家重污染有色冶金企业 ,它的主要污染物是二氧化硫、重金属及烟 (粉 )尘。为适应污染物总量控制工作的需要。对该企业的主要污染物二氧化硫的排放总量进行了较为详细地调查及核算。     

GC-MS法测定植物排放的萜烯类化合物

采用流动式采样与气相色谱-质谱联用法研究了意大利撒丁岛Noak’s Ark自然生态区四种主要灌木树种Juniperus phoenicea(腓尼基桧)，Pistacia lentiscus(黄连木)，Phillyrea angustifilia，Chamaerops humilis(欧洲矮棕)的排放速率和排放特征。结果表明，JuniPerus phoenicea(腓尼基桧)，Pistacia lentiscus(黄连本)，Phillyrea angustifilia主要排放萜烯类化合物，其中包括α-蒎烯、β-蒎烯、苎烯、戊花烃、莰烯、β-水芹烯、桧烯、β-香叶烯和3-蒈烯等；Chamaerops humilis(欧洲矮棕)主要排放异戊二烯。在标准条件下(温度30℃，PAR为1000μmo1．m^-2．s^-1)，四种树种的排放速率分别为0.15、2．10、0．20和1．87μg／g(DW)．h。