垃圾焚烧飞灰中二噁英削减技术研究

二噁英(PCDD/Fs)是多氯代二苯并二噁英和多氯代二苯并呋喃的总称,因具有生物蓄积性、高毒性、难降解等特点而备受关注。垃圾焚烧是二噁英的重要来源,而其中超过50%的二噁英以飞灰形式排出。文章综述了热分解法、光降解法、机械化学法、生物降解法等飞灰二噁英毒性削减技术的国内外研究进展,并在此基础上对飞灰二噁英削减技术研究和管理提出了建议。     

水力负荷对辐流式初沉池污染物去除效果的影响

以沉砂池出水为原水,在沉淀试验研究颗粒截留速度u0基础上,通过动态试验考察水力负荷对辐流式初沉池污染物去除效果的影响。研究结果表明无机悬浮固体(FSS)分离和总悬浮固体(TSS)高效去除的颗粒截留速度u0分别为0.025 m/min和0.05 m/min。由于泥层截留作用,水力负荷qA在46.3 m3/(m2.d)时,辐流式初沉池污染去除最高效,TSS、总氮(TN)和总磷(TP)去除率分别达到81%,23%,59%。     

矿山固体废物的环境影响与综合利用

环境保护和自然资源的合理利用是人类社会可持续发展的基础。矿山固体废物对环境的影响可归纳为污染环境、破坏生态及诱发地质和工程灾害等三个方面。矿山固体废物也是一种可利用的自然资源,目前的利用途径主要有回收利用有用元素,工业原料、回填材料、能源发电、农用肥料和土壤改良剂等。     

钢铁企业固体废弃物资源化利用浅析

固体废物做到资源化即通过综合利用,使有利用价值的固体废物变废为宝,实现资源的再循环利用,是固体废物污染控制一直努力方向。钢铁联合企业生产过程中产生的固体废弃物量大、面广,如对其进行资源化利用不仅可获得好的效益,同时也解决了环保难题。通过借鉴国内外钢铁企业固体废弃物资源化利用成功技术,使我们在开展环境影响评价工作中对钢铁企业固废的资源化利用提出一些切实可行的控制措施。     

北京市城市生活垃圾处理现状与对策

介绍了北京市近几年来生活垃圾的产量及其变化趋势,对北京市近年来生活垃圾处理状况,垃圾处理场建设情况作了简要介绍。最后针对北京市生活垃圾处理面临的问题提出了建议,为北京市垃圾处理可持续发展提供理论依据。     

Antimony smelting process generating solid wastes and dust：Characterization and leaching behaviors

A large amount of solid waste has been produced by the antimony smelting process in the＂World Capital of Antimony＂, Xikuangshan area in China. This study comprehensively investigated the physical and chemical characteristics of the various solid wastes, as well as the leaching behavior of the solid wastes, which included water-quenched slag,arsenic-alkali residue, desulfurized slag and blast furnace dust. These four types of waste were enriched in a variety of heavy metals and metalloids and more specifically with As and Sb levels up to 8.6 × 104 and 3.16 × 105mg/kg, respectively, in arsenic-alkali residue. For desulfurized slag and water-quenched slag, the leaching concentration of Sb significantly exceeded the acceptable limits during the leaching tests using the toxicity characteristic leaching procedure and the synthetic precipitation leaching procedure. In addition, As leaching in arsenic-alkali residue was extraordinarily hazardous, being three orders of magnitude higher than the regulatory level of As. According to the results of the extraction tests, all the tested wastes were classified as hazardous waste.     

Evaluation of soil washing process with carboxymethyl-β-cyclodextrin and carboxymethyl chitosan for recovery of PAHs/heavy metals/fluorine from metallurgic plant site

Polycyclic aromatic hydrocarbons(PAHs)/heavy metals/fluorine(F) mixed-contaminated sites caused by abandoned metallurgic plants are receiving wide attention. To address the associated environmental problems,this study was initiated to investigate the feasibility of using carboxymethyl-β-cyclodextrin(CMCD) and carboxymethyl chitosan(CMC) solution to enhance ex situ soil washing for extracting mixed contaminants. Further,Tenax extraction method was combined with a first-three-compartment model to evaluate the environmental risk of residual PAHs in washed soil. In addition,the redistribution of heavy metals/F after decontamination was also estimated using a sequential extraction procedure. Three successive washing cycles using50 g/L CMCD and 5 g/L CMC solution were effective to remove 94.3% of total PAHs,93.2% of Pb,85.8% of Cd,93.4% of Cr,83.2% of Ni and 97.3% of F simultaneously. After the 3rd washing,the residual PAHs mainly existed as very slowly desorbing fractions,which were in the form of well-aged,well-sequestered compounds; while the remaining Pb,Cd,Cr,Ni and F mainly existed as Fe–Mn oxide and residual fractions,which were always present in stable mineral forms or bound to non-labile soil fractions. Therefore,this combined cleanup strategy proved to be effective and environmentally friendly.     

1987-2006年厦门市土地利用变化检测分析

通过对厦门市五个时相的土地利用变化检测,分析了厦门市1987年-2006年间各分区的土地利用变化及各地类在各年间的变化情况,并分析其变化原因.     

2-萘酚生产废水综合治理与资源化利用工程实例

针对2-萘酚生产废水p H值低、色泽深,亚硫酸盐和萘磺酸盐高、COD浓度高的特点,采用酸化脱硫-两级络合萃取-氧化絮凝工艺处理,介绍了专利工艺的流程设计,给出了主要工艺设计参数及投资运行成本。工程运行结果表明,该工艺设计合理、技术成熟、处理效果稳定,2-萘酚生产废水经处理后达到GB 8978—1996《污水综合排放标准》一级排放标准要求;回收的萘磺酸钠固体可返回2-萘酚生产系统套用;反萃取黑液经蒸发浓缩,合成的减水剂产品各项指标达到或超过GB 8076—2008《混凝土外加剂》高效减水剂指标要求。     

Bitter coil design methodology for electromagnetic pulse metal processing techniques

Electromagnetic pulse metal processing techniques (EPMPT) such as welding, forming and cutting have proven to be an effective solution to specific manufacturing problems. A high pulse magnetic field coil is a critical part of these technologies and its design is a challenging task. This paper describes a Bitter coil design using a newly developed methodology for a simplified analytical calculation of the coil and complementary finite element models (FE) of different complexity. Based on the methodology a Belgian Welding Institute (BWI) Bitter coil has been designed and tested by means of short circuit experiments, impedance and B-field measurements. A good agreement between the calculated and the experimental design parameters was found.