A hybrid method for quasi-three-dimensional slope stability analysis in a municipal solid waste landfill

Limited space for accommodating the ever increasing mounds of municipal solid waste (MSW) demands the capacity of MSW landfill be maximized by building landfills to greater heights with steeper slopes. This situation has raised concerns regarding the stability of high MSW landfills. A hybrid method for quasi-three-dimensional slope stability analysis based on the finite element stress analysis was applied in a case study at a MSW landfill in north-east Spain. Potential slides can be assumed to be located within the waste mass due to the lack of weak foundation soils and geosynthetic membranes at the landfill base. The only triggering factor of deep-seated slope failure is the higher leachate level and the relatively high and steep slope in the front. The valley-shaped geometry and layered construction procedure at the site make three-dimensional slope stability analyses necessary for this landfill. In the finite element stress analysis, variations of leachate level during construction and continuous settlement of the landfill were taken into account. The "equivalent" three-dimensional factor of safety (FoS) was computed from the individual result of the two-dimensional analysis for a series of evenly spaced cross sections within the potential sliding body. Results indicate that the hybrid method for quasi-three-dimensional slope stability analysis adopted in this paper is capable of locating roughly the spatial position of the potential sliding mass. This easy to manipulate method can serve as an engineering tool in the preliminary estimate of the FoS as well as the approximate position and extent of the potential sliding mass. The result that FoS obtained from three-dimensional analysis increases as much as 50% compared to that from two-dimensional analysis implies the significance of the three-dimensional effect for this study-case. Influences of shear parameters, time elapse after landfill closure, leachate level as well as unit weight of waste on FoS were also investigated in this paper. These sensitivity analyses serve as the guidelines of construction practices and operating procedures for the MSW landfill under study.     

三元复合驱采出水中悬浮固体的控制方法

采用向三元复合驱采出水中加入水质稳定剂的方法有效降低采出水中悬浮固体的质量浓度。实验结果表明,将100 g采出水依次经滤纸和孔径为0.45μm的醋酸纤维素膜过滤后,加入1.0 g WSBL-3型水质稳定剂,混合均匀后置于80℃的水浴中静置4 h,取出后再置于40℃的水浴中静置5 min,由此可将采出水中的悬浮固体质量浓度由107 mg/L降至2 mg/L。     

乌鲁木齐市工业固体废物资源化现状、趋势及建议

分析了乌鲁木齐市工业固体废物产生现状及其资源化利用情况,预测了＂十二五＂期间乌鲁木齐市工业固体废物产生量及资源化利用量。针对乌鲁木齐市工业固体废物资源化利用存在的问题,提出了实施工业固体废物资源化利用过程中,应该减少工业固体废物排放总量、扩大资源化利用途径、推进资源回收和资源化利用的产业化进程、加强工业固体废物监督管理工作等建议。     

Pressurized liquid extraction of six tetracyclines from agricultural soils

Veterinary antibiotics used in agriculture can be introduced into the environment through land application of animal manure, accumulating in soils and groundwaters and posing a significant risk to human health and animal well-being. As the analysis of tetracyclines in soil is challenging due to their strong interaction with soil minerals and organic carbon, the objective of this study was to develop a reliable and reproducible method for quantitative analysis of chlortetracycline and oxytetracycline, and their respective metabolites in soils. A method based on pressurized liquid extraction (PLE) with in-cell clean-up was developed for the extraction of chlortetracycline and oxytetracycline and four likely metabolites from a set of four soils. Optimized conditions included a cell size of 22?mL, soil loading of 5?g, pH of 8.0, methanol:water ratio of 3:1, 50?°C, and two cycles. Soil extracts were analysed by high-performance liquid chromatography (HPLC) coupled with ion trap mass spectrometry (MS). Recoveries of seven tetracyclines from soil ranged from 41% to 110%. The limits of detection for tetracyclines were 0.08–0.3 µg g^?1 soil, and intra- and inter-day variation ranged from 0.12–0.34%. The proposed PLE method is suitable for quantification of tetracyclines in agricultural soils at typical concentrations expected in contaminated environments.     

锐钛矿-金红石混合晶型TiO2降解气相苯

用溶胶-凝胶法并通过控制煅烧温度合成不同晶相比的混合晶型纳米TiO_2,在紫外光光照下降解气相苯。考察了苯初始质量浓度、紫外灯光照强度和催化剂加入量对苯去除率的影响;探究了光催化降解气相苯的动力学特征。结果表明:450℃煅烧制备的催化剂降解苯效率最高,此催化剂金红石相质量分数为6.30%;在苯初始质量浓度为74.39 mg/m~3、催化剂加入量为7 g、光照强度为2.18 klux的最佳条件下反应84 min,苯去除率达99.73%;光催化降解率与光照强度之间符合0.5级动力学特征;当催化剂加入量为3 g时,单位时间单位质量催化剂降解苯的质量最多;苯的光催化降解反应均符合一级动力学方程。     

CePO4-TiO2固溶体的NH3-SCR活性

采用共沉淀法合成了不同Ce与Ti摩尔比的CePO₄-TiO₂复合材料,利用XRD、TEM、NH₃-TPD和H₂-TPR技术对其物理化学性质进行了表征,并对其NH₃-SCR活性进行了评价。实验结果表明：随着CePO₄含量的增加,催化剂的活性提高;当Ce与Ti的摩尔比为8:2时催化剂的活性最高,230 ℃的NO转化率达到100%,且具有更广的温度窗口,优于纯CePO₄。表征结果显示,CePO₄与TiO₂形成固溶体后,颗粒尺寸较为均匀,强酸位的数量增多,氧化还原性能提升,从而提高了催化剂的SCR反应活性,同时改善了其抗水抗硫性能。     

固相萃取-气相色谱法测定水样中马拉硫磷残留

采用C-18小柱萃取、毛细管柱分离、气相色谱氢火焰离子化检测器（FID）测定水样中的马拉硫磷,检测限为0．12μg／L。试验了样品流量和洗脱剂对回收率的影响,结果表明样品流量为6mL／min、二氯甲烷作洗脱剂时,回收率较好。测定蒸馏水、地下水和河水样品,相对标准偏差〈2．2％。加标回收率在79．0％-109％之间。     

固相萃取-气相色谱法测定饮用水中甲基汞

根据巯基棉在一定酸性条件下能定量吸附甲基汞的原理,利用多通道并联的固相萃取装置,采用气相色谱(ECD)方法测定饮用水中痕量甲基汞,考察了水样pH值对回收率的影响.方法在0.050 mg/L～1.00 mg/L范围内线性良好,当采样体积为1.0 L时,检出限为0.03 ng/L,标准样品与实际水样平行测定的相对标准偏差均...     

Hydrothermal liquefaction phase behavior of microalgae & model compounds in fused silica capillary reactor

A fused silica capillary reactor combined with a heating/cooling stage, a microscope and a digital camera were used to investigate phase behavior during the hydrothermal liquefaction of microalgae (Dunaliella tertiolecta) and model compounds, including soya protein and glycine, starch, glucose and xylose, stearic acid and palmitic acid. Bubbles were generated at 246°C and disappeared at 360°C upon heating when Dunaliella tertiolecta used as feedstocks. Moreover, liquid products were generated at 300°C upon heating and oily liquid products began to separate out at 250°C upon cooling. The phase behavior of soya protein was similar to that of the Dunaliella tertiolecta. Meanwhile, there only observed the bubbles generation during hydrothermal liquefaction of glycine. Heating the starch, glucose and xylose above 350°C generated black solids from carbonization. Stearic acid and palmitic acid only had the process of melting, dissolution, dispersion and precipitation.     

Some happy,others sad: exploring environmental justice in solid waste management in Kinshasa,The Democratic Republic of Congo

This paper explores the concept of environmental justice (EJ) in solid waste management (SWM) in Kinshasa, the Democratic Republic of Congo (DRC). It evaluates the extent to which EJ occurs in SWM and discusses the factors accounting for this state of affairs. The paper examines the relevant theoretical framework(s) and mechanisms that would facilitate the attainment of EJ in Kinshasa. It is argued that solid waste (SW) often ends up in the poorest and least powerful communities in the cities of the DRC. A qualitative research methodology, which includes exhaustive critical review of the literature, system analysis, reflections from best practices through case studies and discussion with stakeholders, was used for this study. Findings revealed that SWM in Kinshasa is a duty entrusted to publicly-funded municipal authorities. There are evidences of a clear divide between the rich and poor neighbourhoods in the manner SW is managed. This is an inequality that has only recently begun to be recognised as injustice practices in SWM. It is argued that a politico-cultural mechanism on remedying SWM inequities could enable changes that will address EJ in Kinshasa. Such a solution will go directly against the prevailing notion “some happy, others sad”.