油池火作用下钢管混凝土柱温度分布研究

在开敞空间条件下利用油池火模拟不同的火灾场景,对火源燃烧阶段和燃烧结束后钢管混凝土柱的温度变化进行研究。测量了燃料质量变化和钢管混凝土柱的温度分布等参数,分析不同火灾场景下钢管混凝土柱轴向、横截面的温度变化,并以实验工况HS3为例进行深入分析,同时分析了火源的燃烧时间、热释放速率对钢管混凝土柱温度场分布的影响。研究结果表明,钢管混凝土柱纵向温度分布与横向温度分布一样都存在明显的温度梯度,其表面钢管温度变化受火场热释放速率影响较大,而内部混凝土的温度变化则主要受火场持续时间的影响。     

Diazinon leaching through a sandy soil amended with different humic materials

The water leaching of diazinon (O,O‐diethyl‐O‐2‐isopropyl‐6‐methylpyrirnidin‐4‐yl phosphoroth‐ioate) through soil columns, was studied after column amendments with two well characterized humic acids (HA), in both liquid and solid state, and with the original raw organic materials, an oxidized coal and a leonardite, from which the HA were extracted. The percolation curves and the pesticide distribution over the soil columns showed that the addition of the raw organic materials and the solid HAs reduced significantly the mobility of the pesticide along the soil column. The oxidized coal was more effective than the leonardite original material; the different origin of the two carbon‐rich materials had an influence on the diazinon movement along the soil columns and such difference was enhanced with increasing addition rates. Moreover, incubation at field capacity for two months of the soil columns treated with raw oxidized coal and leonardite, largely enhanced the described effects on pesticide behaviour. A complete adsorption of diazinon on columns and a practical absence of leaching was observed when the HA from both materials were added in dissolved form. These results were explained with the swelling of the humic micelles in water and the enhanced availability of inner hydrophobic surfaces for the strong adsorption of diazinon. The water diffusion into the solid humic materials after two months incubation, also explains their high pesticide retention capacity. This work indicates the usefulness of either solid o dissolved humic substances, with the proper hydrophobic character, in preventing the vertical leaching of non‐polar organic pesticides in soils.     

Cu(Ⅱ)印迹[CTS/PVP]和[CTS/PVP/C]材料的制备及表征

以壳聚糖(CTS)、聚乙烯吡咯烷酮(PVP)、活性炭(C)为基材,Cu(Ⅱ)为印迹离子,制备了CTS/PVP共混印迹球[Cu(Ⅱ)-IICP]和CTS/PVP/C共混印迹球[Cu(Ⅱ)-IICPC].以Cu(Ⅱ)的吸附量作为评价指标,对两种共混印迹球的制备条件进行了优化.研究结果表明,当CTS/PVP的质量比为6∶4,活性炭质量分数为0.6%,Cu(Ⅱ)模板剂质量分数为0.05%,所制备的两种共混印迹球吸附性能较佳,且对Cu(Ⅱ)有较好的选择吸附性.物理吸附分析结果表明,与未印迹相比印迹材料的比表面积明显增大.FTIR谱图分析,Cu(Ⅱ)模板主要与CTS和PVP中的—NH2和—OH发生了配位作用.XRD谱图分析结果表明,CTS与PVP、C、Cu(Ⅱ)之间发生了相互作用,改变了CTS原有的晶体结构,使其结晶度降低.     

Toxic elements leaching in different soils affected by the spill from the aznalcollar pyrite mine (Sevilla,Spain)

A study has been made of the leaching of Cd, Zn, Pb, Cu, Tl and As in three representative soils of the zone affected by the spill from a pyrite mine in Aznalcollar (Sevilla, Spain) employing packed soil columns. According to the breakthrough and cumulative leaching curves, the relative mobilities of the different toxic elements in the columns are as follows: Tl > Cd > Zn > As > Cu > Pb. The results also show that the soils themselves have a good capacity for immobilizing the soluble fraction of the elements from the spilled mud, this capacity varying as follows: clayey soil with a high carbonate content > clayey soil with a moderate carbonate content > sandy‐clay loam soil with a low carbonate content. The results obtained in the work are a valuable contribution to the necessary assessment of the impact of the toxic spill on underground waters.     

钒基催化剂同步去除燃煤烟气中甲苯与NOx研究

采用不同工艺制备V₂O₅-WO₃-MoO_x/TiO₂堇青石整体式催化剂,以甲苯和NO为探针分子,考察了Mo的负载量、涂覆方法、粘结剂的种类等制备工艺对整体式催化剂性能的影响,用XRD、SEM-EDS、FT-IR、BET等技术对催化剂进行了表征分析.结果表明,采用涂敷法,以添加量为1%的甲基纤维素为粘结剂所制备的V1W6Mo3/TiO₂堇青石蜂窝陶瓷整体式催化剂具有最优活性和稳定性（T₉₀为307℃,负载率为28.26%,脱落率为6.81%）,在燃煤烟气中具有优异的同步去除VOCs与NO性能,甲苯去除率可达99%,NO去除率为100%,N₂选择性为99%.XRD、SEM-EDS表明V、W、Mo活性组分分布均匀且高度分散.FT-IR证明添加甲基纤维素的整体式催化剂具有优异的抗硫性能.     

含氧非烃在土壤剖面上迁移行为的土柱淋滤模拟研究

为了揭示土壤剖面中含氧非烃污染物的迁移特征,以及TOC和淋滤水量等因素对迁移作用的影响,选择了部分典型的含氧非烃开展了纵向迁移的土柱淋滤实验,对原土及添加污染物的土柱淋滤实验后样品中含氧非烃的含量及组成进行了对比分析.结果表明,土柱淋滤实验后,土柱表层添加的含氧非烃主要残留在土柱表层0~5 cm范围内,但相比所添加的化合物的量均有不同程度的降低,土柱深部(>10 cm)土壤中含氧非烃含量仍然很低,甚至低于原土中的,在TOC较高的土柱中,这种现象尤为突出.说明土柱淋滤实验过程中,不同剖面含氧非烃均存在向下迁移的现象,且以水溶方式迁移为主.不同含氧非烃单体含量均有随深度增加而降低的趋势,表明其在土壤剖面淋滤过程中均具有一定的迁移性,但不同性质的含氧非烃单体在表层土中残留量及组成差别较大,说明不同化合物迁移能力存在差别,其中,胆甾醇、β-谷甾醇、正构十六烷酸和邻苯二甲酸二丁酯迁移性较强.土壤TOC和淋滤水量对含氧非烃在土壤剖面的迁移作用都有不同程度的影响,淋滤水量相同时,TOC含量越高,土壤中有机质越丰富,越容易富集含氧非烃;TOC相同时,淋滤水量越大,含氧非烃迁移量越大,迁移的深度越大,尤其在TOC含量较低时更明显.     

Determination of particulate polycyclic aromatic hydrocarbons in ambient air by gas chromatography-mass spectrometry after molecularly imprinted polymer extraction

A solid phase extraction procedure (SPE) is described for the quantitative analysis of polycyclic aromatic hydrocarbons (PAHs) in atmospheric particulate matter (PM), as ubiquitous environmental pollutants routinely measured in air quality monitoring. A SPE cartridge was used based on a molecular imprinted polymer (MIP-SPE) properly tailored for selective retention of PAHs with 4 and more benzene fused rings. The performance of the clean-up procedure was evaluated with the specific concern of selective purification towards saturated hydrocarbons, which are the PM components mostly interfering GC analysis of target PAHs. Under optimized operative conditions, the MIP-SPE provided analyte recovery close to 95% for heavier PAHs, from benzo(α)pyrene to benzo(ghi)perylene, and close to 90% for four benzene rings PAHs, with good reproducibility (RSDs: 2.5%-5.9%). Otherwise, C₁₇-C₃₂ n-alkanes were nearly completely removed. The proposed method was critically compared with Solid Phase Micro Extraction (SPME) using a polyacrylate fiber. Both methods were successfully applied to the analysis of ambient PM_2.5 samples collected at an urban polluted site. Between the two procedures, the MIP-SPE provided the highest recovery (R% ≥ 93%) for PAHs with 5 and more benzene rings, but lower for lighter PAHs. In contrast, SPME showed a mean acceptable R% value (∼ 80%) for all the investigated PAHs, except for the heaviest PAHs in the most polluted samples (R%: 110%-138%), suggesting an incomplete purification from the interfering n-hydrocarbons.     

磁性炭微球表面印迹吸附材料的制备及其对氨苄西林识别与选择性吸附

以核桃壳为原料,利用溶剂热法制备了磁性炭微球(MCMs),结合表面印迹技术制备了基于MCMs的磁性炭微球表面分子印迹材料(MMIPs).通过FT-IR、TGA、VSM和TEM等表征手段对其理化性能进行了表征,结果表明MMIPs为球形,印迹聚合层厚度50~80 nm,具有热稳定性和磁稳定性.采用吸附实验研究了MMIPs对AMP的识别与选择性吸附性能.Langmuir等温模型能较好地描述MMIPs对AMP的吸附平衡数据,25℃时MMIPs的单分子层最大吸附容量为40.96 mg·g-1.准二级动力学模型能较好的描述MMIPs对AMP吸附动力学行为.选择性分析结果表明,MMIPs对AMP具有较好地选择识别性,并且MMIPs可以循环使用5次.结合高效液相色谱分析技术,MMIPs已成功应用于牛奶样品中痕量AMP的分离、富集和回收,AMP的回收率为92.78%.     

Leaching of fenamiphos,fenamiphos sulfoxide and fenamiphos sulfone in soil columns

Abstract

Leaching of fenamiphos and its thiooxidation products, sulfoxide and sulfone, has been studied in two different soils in laboratory conditions. Fenamiphos was much less mobile than its derivatives. A large volume of water was necessary to leach completely the three chemicals. Fenamiphos required an amount of water twice as large as that required by either sulfoxide or sulfone. Mobility and leaching efficiency of the chemicals examined were highly dependent on the properties of the two soils considered.     

Revised emergency vacuum relief device sizing for atmospheric distillation systems

Conventional vacuum relief methodologies are usually protective responses; that is, they accomplish their purpose by substitution of an inert gas (usually nitrogen) for the process gases removed by an external vacuum source, or for condensable vapour collapsed by an internal process mechanism (e.g. condensation). While this approach is theoretically possible for all potential vacuum scenarios, it becomes practically impossible to implement for installations where a rapid phase change can impart near-instantaneous system pressure reductions. The procedure outlined in this paper takes a preventive approach: eliminate the source of vacuum generation before the safe lower system pressure limit is reached. For distillation and other refluxing systems, this vacuum source is usually the main overhead condenser, which is designed to collapse large volumes of condensable vapour. To eliminate the vacuum source requires elimination of the system's ability to rapidly condense vapour. This goal is accomplished by introduction of inert gas directly into the condensing system to ‘blanket’ the heat transfer surface and stop condensation. The procedure determines the rate, amount and location for introduction of inert gas. The required design data include: (i) system starting pressure, (ii) maximum allowable system vacuum, (iii) volume of the condensing system, and (iv) normal system condensing rate. By determining the rate at which the condenser removes vapour volume from the system, and designing an inert gas delivery system to meet or exceed this rate, the vacuum generation potential of the system is effectively eliminated using a much smaller quantity of inert gas than with the more traditional volume substitution methods.