温度与pH对生物合成施氏矿物在酸性环境中溶解行为及对Cu2+吸附效果的影响

探析施氏矿物在不同温度、pH下的溶解行为,对其在酸性煤矿废水(ACMD)重金属去除领域的应用具有重要的工程指导意义.本研究通过摇瓶实验,在0.16mol·L-1FeSO4·7H2O,初始pH为2.5的酸性体系中,采用氧化亚铁硫杆菌A.ferrooxidans催化合成施氏矿物.考察了15℃与30℃,pH为2.0$6.0环境条件下矿物的溶解行为,及生物合成施氏矿物对酸性体系Cu2+的吸附去除效果.研究结果表明,经过24h反应,施氏矿物合成体系pH从原始2.50降低至2.18,体系Fe2+氧化完全,27.3%的铁离子参与矿物的合成,矿物分子式可表示为Fe8O8(OH)4.22(SO4)1.89.生物合成施氏矿物在温度为15℃,pH分别为3.2、3.0、2.8、2.6、2.4、2.2与2.0液态体系中振荡72h,矿物溶解率分别为1.92%、3.34%、5.90%、13.09%、28.74%、44.53%与61.46%.在温度为30℃的上述酸度体系中,矿物溶解率在相应时间却达到2.04%、3.98%、8.34%、20.53%、43.50%、96.74%与99.92%.在pH≥3.5的不同温度液态体系中该矿物无溶解迹象.在15℃,pH为6.0、5.0、4.5、4.0与3.5,Cu2+浓度为40mg·g-1的液态体系中,生物合成施氏矿物对Cu2+的吸附量为(50.9±2.2)、(47.3±13.3)、(40.5±4.7)、(31.1±5.0)及(16.9±6.5)mg·g-1.体系酸度一定,施氏矿物在15℃与30℃条件下对Cu2+的吸附效果无显著差异.本研究结果对生物合成施氏矿物在ACMD重金属去除工程应用提供必要的参数支撑.     

NO参与铝诱导蚕豆保卫细胞死亡的调控

铝(Al)是地壳中含量最丰富的金属元素,是酸性土壤中导致植物生长抑制和作物产量下降的一个主要因素,但铝毒性作用机制尚不清楚.本文以蚕豆叶表皮为材料,研究铝胁迫对气孔保卫细胞活性的影响,探讨NO在铝诱导细胞死亡中的作用.结果表明,一定浓度的A1Cl3可诱导气孔保卫细胞活性降低,部分细胞死亡,且随着铝浓度的增高细胞死亡率增高.死细胞呈现核固缩、核崩解、凋亡小体等典型凋亡特征,且凋亡抑制剂Z-Asp-CH2-DCB能阻止AlCl3诱发的细胞死亡.用NO清除剂c-PTIO、NO合酶抑制剂L-NAME或硝酸还原酶抑制剂NaN3降低铝处理组胞内NO后,细胞死亡率显著降低,胞内ROS、Ca2+水平同期降低;NaN3还能降低铝处理组中具有程序性死亡特征的细胞比率.用ROS清除剂AsA清除铝处理组胞内ROS后,细胞死亡率显著降低,胞内Ca2+和NO水平亦显著降低;铝处理液中加入Ca2+通道抑制剂LaCl3后,细胞死亡率低于铝单独处理组,胞内ROS和NO水平无明显改变.研究结果表明,铝胁迫引起的胞内NO合成增加通过Ca2+信号途径介导了保卫细胞的程序性死亡.     

温度对生物强化除磷工艺反硝化除磷效果的影响

以处理城市污水的中试规模生物强化除磷A2/O活性污泥工艺系统为研究对象,考察了温度对系统COD去除和脱氮除磷效果的影响,特别是温度对活性污泥反硝化除磷性能的影响.结果表明,当温度从(30.9±0.8)℃降低到(9.1±0.6)℃时,A2/O系统的脱氮除磷效果显著下降,系统对TN和TP的污泥去除负荷明显下降.通过污泥反硝化除磷活性实验发现,随着温度的降低,系统中活性污泥的最大厌氧释磷速率、最大好氧吸磷速率和最大缺氧吸磷速率都降低.活性污泥中反硝化除磷菌(DPB)占聚磷菌(PAOs)总量的比例随温度降低稍有下降,但平均值仍维持在47.5％左右.用阿伦尼乌斯公式对实验结果进行拟合,得到系统中活性污泥聚磷菌厌氧释磷反应活化能Ea1为148.0 kJ· mol-1,聚磷菌好氧吸磷反应活化能Ea2为228.8 kJ·mol-1,发生在缺氧条件下反硝化除磷菌的吸磷反应活化能Ea3为315.8 kJ·mol-1.对不同温度下污泥絮体粒径分析结果表明,随温度降低,粒径分布更加集中,系统中活性污泥絮体颗粒平均粒径减小,不利于污泥絮体内部反硝化除磷缺氧微环境的形成.     

呼和浩特市可镇污水处理厂工程设计

呼和浩特市可镇污水处理厂近期建设规模1.0×104m3/d,远期总规模2.5×104m3/d。污水处理主体工艺采用组合式A2/O生化池+砂滤,污泥处理采用污泥贮池+带式浓缩脱水一体机,尾水采用液氯消毒,设计出水水质执行GB 18918—2002《城镇污水处理厂污染物排放标准》一级A排放标准。介绍了该工程的工艺流程、设计参数,总结分析了工艺设计的技术特点。同时阐述了针对低温条件下的运行保障措施和要求,为寒冷地区同类污水处理厂的设计提供参考和借鉴。     

FY2 号气象卫星估算地面太阳辐射研究

综合考虑太阳因素、地形因素、地表积雪覆盖情况、云量以及非均质大气对太阳辐射的影响,基于FY2 号静止卫星构建晴空太阳总辐射计算模型,并利用山西省3 个辐射观测站2011 年逐时、逐日、逐月太阳总辐射观测资料对其估算结果进行检验。研究结果显示：逐时误差在±1 MJ·m^-2之间,逐日误差在±5 MJ·m^-2之间,表明模型计算的太阳辐射误差较小,稳定性较好;逐月误差结果显示,三个站模拟值都大于实测值,且误差趋势一致,均表现为冬季误差高于夏季;进一步对模拟值和实测值进行相关性分析,三站线性拟合度均在0.86～0.92 之间,且相关系数均达到显著相关水平,表明模型计算的太阳辐射准确性和精度较高,且在数值拟合上较好地反映了实际的太阳总辐射量,证实该模型应用于FY2 号气象卫星的可行性。     

Biodegradation of 2-methylquinoline by Enterobacter aerogenes TJ-D isolated from activated sludge

Bacterial strain Enterobacter aerogenes TJ-D capable of utilizing 2-methylquinoline as the sole carbon and energy source was isolated from acclimated activated sludge under denitrifying conditions. The ability to degrade 2-methylquinoline by E. aerogenes TJ-D was investigated under denitrifying conditions. Under optimal conditions of temperature (35℃) and initial pH 7, 2-methylquinoline of 100 mg/L was degraded within 176 hr. The degradation of 2-methylquinoline by E. aerogenes TJ-D could be well described by the Haldane model (R² > 0.91). During the degradation period of 2-methylquinoline (initial concentration 100 mg/L), nitrate was almost completely consumed (the removal efficiency was 98.5%), while nitrite remained at low concentration (< 0.62 mg/L) during the whole denitrification period. 1,2,3,4-Tetrahydro-2-methylquinoline, 4-ethyl-benzenamine, N-butyl-benzenamine, N-ethyl-benzenamine and 2,6-diethyl-benzenamine were metabolites produced during the degradation. The degradation pathway of 2-methylquinoline by E. aerogenes TJ-D was proposed. 2-Methylquinoline is initially hydroxylated at C-4 to form 2-methyl-4-hydroxy-quinoline, and then forms 2-methyl-4-quinolinol as a result of tautomerism. Hydrogenation of the heterocyclic ring at positions 2 and 3 produces 2,3-dihydro-2-methyl-4-quinolinol. The carbon-carbon bond at position 2 and 3 in the heterocyclic ring may cleave and form 2-ethyl-N-ethyl-benzenamine. Tautomerism may result in the formation of 2,6-diethyl-benzenamine and N-butyl-benzenamine. 4-Ethyl-benzenamine and N-ethyl-benzenamine were produced as a result of losing one ethyl group from the above molecules.     

Effect of transition metal doping under reducing calcination atmosphere on photocatalytic property of TiO2 immobilized on SiO2 beads

TiO₂ immobilized on SiO₂ (TiO₂/SiO₂) have been prepared by sol-gel method and various ions of transition metals (Cr³⁺, Co²⁺, Ni²⁺, Cu²⁺, and Zn²⁺) were doped on the photocatalyst using wet impregnation method under reducing calcination atmosphere. The photocatalytic activity of metal doped TiO₂/SiO₂ towards phenol degradation under black light irradiation were investigated and compared with undoped TiO₂/SiO₂. The results showed that the photoresponse of Cu²⁺ and Zn²⁺ doped TiO₂/SiO₂ were larger than undoped TiO₂/SiO₂, indicating that the photogenerated carriers were separated more efficiently in Cu²⁺ and Zn²⁺ doped TiO₂/SiO₂. The reactivity was in the order of Cu²⁺ > Zn²⁺ > Ni²⁺ > Cr³⁺ > Co²⁺. The different photoreactivity was ascribed to combine effect of the different ionic radii and photocorrison tendency of the dopants. The sample was also characterized by surface analytical methods such as X-ray diffraction, scanning electron micrograph/electron dispersive X-ray analyzer and UV-Vis absorption spectrum.     

Adsorption of 2-mercaptobenzothiazole from aqueous solution by organo-bentonite

The adsorption behavior of 2-mercaptobenzothiazole onto organo-bentonite was investigated.Natural bentonite from Gaozhou in Guangdong Province,China was collected.Organo-bentonite was prepared by intercalation of cetyltrimethyl ammonium bromide into the natural bentonite.The physicochemical properties of the prepared organo-bentonite were characterized by X-ray diffraction,N2 adsorption-desorption isotherm and Fourier transform infrared spectroscopy.The results showed that montmorillonite is the main component of the natural bentonite.The basal spacing of the natural bentonite is 1.47 nm,which increased to 1.98 nm on intercalation with cetyltrimethyl ammonium bromide.Moreover,both the surface area and pore volume increased with intercalation.Clear CH2 stretching(3000-2800 cm-1) and scissoring(1480-1450 cm-1) modes of the intercalated surfactants were observed for organobentonite.Compared with the pseudo first-order kinetic model,the pseudo second-order kinetic model is more suitable to describe the adsorption kinetics of 2-mercaptobenzothiazole onto organo-bentonite.The adsorption capacity of 2-mercaptobenzothiazole onto organo-bentonite increased with increasing initial concentration of 2-mercaptobenzothiazole,but decreased with increasing adsorbent dosage.The adsorption isotherm of 2-mercaptobenzothiazole onto organo-bentonite fits well with the Langmuir model.The maximum adsorption capacity of organo-bentonite for 2-mercaptobenzothiazole was 33.61 mg/g,indicating that organo-bentonite is a promising adsorbent for 2-mercaptobenzothiazole.     

Formic acid as an alternative reducing agent for the catalytic nitrate reduction in aqueous media

Formic acid was used for the nitrate reduction as a reductant in the presence of Pd:Cu/γ-alumina catalysts. The surface characteristics of the bimetallic catalyst synthesized by wet impregnation were investigated by SEM, TEM-EDS. The metals were not distributed homogeneously on the surface of catalyst, although the total contents of both metals in particles agreed well with the theoretical values. Formic acid decomposition on the catalyst surface, its influence on solution pH and nitrate removal efficacy was investigated. The best removal of nitrate (50 ppm) was obtained under the condition of 0.75 g/L catalyst with Pd:Cu ratio (4:1) and two fold excess of formic acid. Formic acid decay patterns resembled those of nitrate removal, showing a linear relationship between kf (formic acid decay) and k (nitrate removal). Negligible amount of ammonia was detected, and no nitrite was detected, possibly due to buffering effect of bicarbonate that is in situ produced by the decomposition of formic acid, and due to the sustained release of H2 gas.     

我国水泥工业碳排放特征及动态变化分析

水泥工业是温室气体二氧化碳(CO2)的主要排放源,利用碳排放数学模型计算2001-2010年我国水泥工业碳的排放量,分析碳排放量的变化特点和发展趋势。结果表明:水泥工业碳排放总量逐年增长,与水泥产量和排放强度呈线性关系。"十一五"期间单位产品碳排放强度由0.69 t/t下降到0.65 t/t。万元GDP碳排放量2008年达到最低值为0.295 1 t,平均每年万元GDP碳排放量下降2.85%。水泥工业十年间实施节能降耗、资源循环利用、提高经济效益等措施,对于减少碳排放具有明显效果。