Anaerobic tapered fluidized bed reactor for starch wastewater treatment and modeling using multilayer perceptron neural network

Anaerobic treatability of synthetic sago wastewater was investigated in a laboratory anaerobic tapered fluidized bed reactor(ATFBR) with a mesoporous granular activated carbon(GAC)as a support material.The experimental protocol was defined to examine the effect of the maximum organic loading rate(OLR),hydraulic retention time(HRT),the efficiency of the reactor and to report on its steady- state performance.The reactor was subjected to a steady-state operation over a range of OLR up to 85.44 kg COD/(m~3.d).The COD removal efficiency was found to be 92% in the reactor while the biogas produced in the digester reached 25.38 m~3/(m~3·d) of the reactor. With the increase of OLR from 83.7 kg COD/(m~3.d),the COD removal efficiency decreased.Also an artificial neural network(ANN) model using multilayer perceptron(MLP)has been developed for a system of two input variable and five output dependent variables. For the training of the input-output data,the experimental values obtained have been used.The output parameters predicted have been found to be much closer to the corresponding experimental ones and the model was validated for 30% of the untrained data.The mean square error(MSE)was found to be only 0.0146.     

Fe^0-厌氧微生物体系处理活性艳红X-3B的试验研究

采用间歇式摇床试验,研究了葡萄糖共基质条件下Fe^0-厌氧微生物体系中Fe^0投加量、pH值、染料初始浓度对活性艳红X-3B模拟废水脱色率的影响,比较了Fe^0-厌氧微生物、纯厌氧微生物及纯Fe^0 3种体系中废水的脱色效果。结果表明：Fe^0-厌氧微生物体系中初始浓度（50～500mg／L）对活性艳红X-3B的脱色率影响不大;而Fe^0投加量、pH值存在一个最佳范围;当Fe^0投加量为260mg／L,pH值为6．0,污泥浓度为0．35gVSS／L,停留时间约为30h时,体系中活性艳红X-3B的脱色率可达90％左右,比相同试验条件下纯Fe^0、纯厌氧微生物体系达到此脱色率所需时间分别缩短了约1／2、7／10。在Fe^0-厌氧微生物体系中,由紫外可见分光光度分析可推测活性艳红X-3B的脱色机理主要是其偶氮键发生断裂,生成苯胺和萘类物质,而且苯胺和萘类物质能得到进一步降解。     

微量金属元素及其配合物对厨余垃圾甲烷发酵的影响

生物可利用的微量金属元素不仅能够保证污染物以最大的速率转化,而且还可以使某些特殊的转化得以发生,并提高微生物对有毒污染物质的耐受能力。在研究厨余垃圾总固体浓度(total solid, TS)、接种量和C/N比对厨余垃圾厌氧发酵影响的基础上,重点探讨微量金属元素钴及其配合物丝氨酸对厨余垃圾厌氧发酵甲烷产量及关键酶含量的影响。结果表明,当TS为0.5%、接种污泥量为100 mL/L和C/N比为20∶1时,厨余垃圾厌氧发酵的甲烷产率较高,为367 mL/g COD;添加2 μmol/L的微量金属元素钴-配合物丝氨酸时,甲烷产率则提高到432 mL/g COD,相应地,辅酶M的含量由空白实验的41.21 μmol/g VSS提高到54.64 μmol/g VSS,辅酶F₄₂₀的含量由0.31 μmol/g VSS提高到0.48 μmol/g VSS。     

炭纤维载体固定床厌氧发酵启动运行效果实验

以开发高效率、抗冲击性能强的高浓度有机废水沼气发酵技术为目的,用传统的 UASB反应器作为对照,研究了以炭纤维为生物膜载体的固定床厌氧反应器的启动运行效果。反应器进口废水 COD 为 5 000 mg/L, 水力停留时间 (HRT) 由213 h 逐步缩短为35 h,进水有机容积负荷(OLR)由0.56 kg COD/ (m³·d)提到3.45 kg COD/(m³·d)。结果表明,固定床反应器厌氧发酵的效率比对照高,出水 pH 值也比对照稳定;运行到第 50 d 时,固定床厌氧反应器和对照的 COD去除率分别由第 7 d 的36.56%和33.58%上升到87.9%和62.6%;固定床厌氧反应器的容积比产气率最高为1.16 m³/(m³·d),累计产气量为415.59 L,而对照的容积比产气率最高值仅为0.31 m³ /(m³·d),累计产气量为 71.66 L,前者最高容积比产气率和累计产气量分别是后者的3.74倍和5.78倍。固定床厌氧反应器的启动速度、COD 去除率和产甲烷效率显著地高于对照反应器。     

厌氧序批式反应器内挥发性脂肪酸积累特性研究

小试规模的厌氧序批式反应器（ASBR）,通过人工配水,研究了启动3个月时间以及一个运行周期内反应器内挥发性脂肪酸（VFA）的积累情况,并通过分析期间产甲烷活性的变化说明了控制VFA积累的重要性。经过近120 d的运行,乙酸和丙酸的最大比产甲烷活性分别提高了1.8和2.2倍,说明反应器的启动过程即是微生物群落的优化和选择的过程,ASBR的抗冲击的能力较强说明随启动的进行和种群的优化,活性污泥凝聚性能增强,对VFA的降解能力增强。     

联合生物法处理炼油厂含油污泥的研究

大港石化公司采用联合生物法处理含油污泥,对使用好氧、厌氧工艺处理含油污泥的结果进行了探讨。实验结果表明:先进行好氧处理然后脱水再进行厌氧堆肥工艺处理含油污泥,除油率达到97.6%,除磷、钾的指标低于《城镇垃圾农用控制标准》(GB8172-87)的要求外,其他指标均符合该标准要求,且避免了二次污染。     

NaCl和KCl对厌氧污泥抑制的动力学研究

在厌氧颗粒污泥和厌氧絮状污泥系统中,进行盐质量浓度(NaCl或KCl质量浓度,下同)对厌氧污泥抑制动力学的研究,得到不同拟合的COD降解动力学方程及参数.实验结果表明:当盐质量浓度为10～30 g/L时,KCl对厌氧污泥的COD比降解速率的抑制程度大于NaCl;当盐质量浓度由0 g/L增至10 g/L时,半速率常数逐渐增加;当盐质量浓度由10 g/L增至30 g/L时,半速率常数逐渐减小;在厌氧污泥系统中,NaCl抑制作用下的盐抑制常数高于KCl,且颗粒污泥的盐抑制常数高于絮状污泥.     

UASB反应器处理染料及印染废水的研究进展

综述了国内外UASB反应器处理染料及印染废水的研究概况.分析了UASB反应器处理废水存在的问题,并给出了相应的建议.展望了UASB反应器处理染料及印染废水的发展趋势,指出厌氧UASB-好氧法组合工艺是目前处理染料及印染废水的一种经济而有效的方法.     

过氯乙烯滤膜采样-酸消解-钼蓝光度法测定磷酸雾

建立了过氯乙烯滤膜采样 -酸消解 -钼蓝分光光度法测定磷化车间磷酸雾的监测方法。实验室模拟采样的捕集效率为 95 7%～ 99 1 %。单个实验室对含 5μg和 1 5μg样品进行多次测定 ,其相对标准差小于 5% ,样品加标回收率为 98 2 %～ 1 0 0 5% ,方法检测限为 0 0 0 7mg/m3。对标样测定 ,结果均在给定值范围内。用该法与等离子发射光谱法(ICP)对 5个样品进行比对测定 ,结果均令人满意。     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.