潮汐流人工湿地低温下 NH4+ -N去除模型的比较和优化

针对目前人工湿地在低温条件下脱氮效能降低的问题,本研究对每天3个运行周期的潮汐流人工湿地在低温条件下对NH4+ -N的处理效能进行研究,同时利用表观动力学模型、多元参数回归模型及Monod机制模型对NH4+-N的去除过程进行拟合.结果显示,在平均水温为9～13℃条件下,每天3个运行周期的潮汐流人工湿地对NH4+-N有良...     

自然保护区生态补偿定量方案研究——基于“虚拟地”计算方法

自然保护区生态补偿的“补给谁”和“补多少”在理论和实践上都是生态补偿中的重点和难点所在。传统的通过计量保护区正外部性以确定生态补偿数量的方法存在两个主要问题：一是违背经济学原理,二是与管理体制不符且法理不足。据此,并考虑到中国相当数量的保护区“没有保护好”的主要因素是保护区社区居民生产生活的干扰,论文认为应通过控制保护区社区的负外部性来达成对保护区的生态补偿。通过生产函数理论分析,发现通常情况下保护区社区的经济产出与土地面积单调正相关,因此在没有生态补偿的情况下,保护区的划建会使周边社区居民经济收入减少,解决周边社区对保护区干扰的根本途径是利用生态补偿资金发展替代产业以提高单位面积土地的经济产出。以此认识为基础,文章提出了“虚拟地”概念并发展了定量方法来确定保护区的生态补偿最低标准,采用武夷山保护区的数据进行了这一方法的案例分析。     

国内外土地利用区划研究的回顾与展望

土地利用区划是从区域角度观察和研究地域综合体,探讨土地利用的发展历史、现状特点、变化过程及趋势,从最大限度发挥土地生产潜力及改善土地生态系统的结构与功能出发,对土地的合理利用方向,包括确定国民经济各部门用地的合理分配、结构和布局形式等,在地域上进行分区。通过简要回顾国内外土地利用区划研究的发展历程,总结了土地利用区划研究的理论方法特点及存在的问题,并在此基础上探讨今后土地利用区划研究的重点及发展方向：从自然要素向自然与人文要素有机结合方向转变;从大空间尺度向多空间尺度方向转变;从传统的区划方法向综合集成的新技术手段转变;从静态的区划研究向多要素、多过程耦合的动态区划研究方向转变。     

漆酶催化酚类、苯胺类化合物的动力学分析及其测定废水中邻苯二酚的应用研究

含酚、苯胺类废水是环境中水污染的重要来源之一.本研究以漆酶分析酚类及苯胺类底物的动力学特性为基础,建立酚类、苯胺类化合物的分析方法.以分光光度法测定漆酶催化0～10mg/L酚类及苯胺类底物的反应速率,作出底物浓度与反应速率的标准曲线,采用漆酶筛查并检测了3种焦化废水中非挥发酚类含量.结果表明,漆酶的酚类及苯胺类底物主要以多元酚、氨基酚及多元胺为主,其中酚类的最适pH在7.0左右,苯胺类在4.5～5.0之间,各底物Km值大小在0.4～10mmol/L之间.除联苯胺外,分光光度法所得到的标准曲线均具有较好的一级反应动力学线性关系,相关系数R2在0.96以上.3种焦化废水中邻苯二酚含量分别为190.5、265.8和155.3mg/L,回收率介于91.9%～115.8%之间.     

三峡库区悬移质泥沙对磷污染物的吸附解吸特性

就三峡库区悬移质泥沙对磷污染物的吸附解吸特性从野外同步监测和室内试验研究两个方面展开研究。选取长江干流、嘉陵江和乌江共7个监测断面于2002年和2003进行野外同步监测,测试结果表明：水中的悬移质泥沙对水中各种覆存形态的磷污染物浓度具有显著影响,单位重量泥沙对磷的吸附量与水体总泥沙含量、泥沙粒径有密切关系。采集寸滩断面泥沙对磷酸盐吸附解吸特性进行室内试验研究,并根据Langmuir吸附动力学方程对吸附解吸过程进行了拟合,发现吸附速率常数k随着泥沙粒径的增加而呈递增变化,而磷酸盐初始浓度对k值的影响并不明显,同时,磷酸盐解吸量随着泥沙浓度的增加和粒径的增加呈递减变化,k值随着泥沙粒径的增加而呈递增变化,泥沙浓度对k值的影响不明显。     

生物活性炭去除水中挥发性苯系物的基础研究

采用连续流生物活性炭(BAC)工艺处理水中挥发性苯系物(BTEX,包括苯、甲苯、乙苯、二甲苯),评价进水负荷、活性炭炭型等因素对于BAC处理性能的影响.研究表明,在40d的处理时间内,除苯之外,其余BTEX的BAC出水中均未检出苯系物(进水为6mg/L).为了检验BAC在高BTEX负荷情况时的处理效果,将进水浓度设定为19~32mg/L左右,在EBCT为1.2min条件下同样只有苯的出水浓度上升至10mg/L(C/Cin为0.45),然后略有下降,最终保持在5~10mg/L(C/Cin为0.3以下),其余苯系物出水浓度均一直保持小于5mg/L.这表明BAC可以有效地处理高负荷BTEX(8.68~12.9kgTOC/(m3·d))的进水.生物活性炭对于活性炭吸附容量的恢复有比较明显的作用,煤质炭和椰壳炭的生物再生效率分别为53.6%和26.6%,煤质炭再生效率高的原因可能是其具备更多的大型中孔和大孔.     

Effect of platinum on the photocatalytic degradation of chlorinated organic compound

TiO2 nanoparticles, doped with di erent Pt contents, were prepared by a modified photodeposition method using Degussa P-25 TiO2, H2PtCl6 6H2O and methanol as the solvents. The physicochemical properties of Pt/TiO2 were investigated by the nitrogen adsorption and desorption isotherm measurement technique, X-ray di raction analysis and photoluminescence spectra, respectively. Reaction rates from photocatalytic removal of dichloromethane over Degussa P-25 TiO2 and Pt/TiO2 were evaluated. The average diameter and BET surface area of the TiO2 catalyst particles were 300 nm and 50 m2/g, respectively. The degradation e ciency was 99.0%, 82.7%, 55.2%, and 57.9% with TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. And the degradation e ciency was 99.3%, 79.7%, 76.5%, and 73.4% with a 0.005 wt.% Pt/TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. In addition, we found that the photoluminescence emission peak intensities decreased with increases in the doping amount of Pt, which indicates that the irradiative recombination was weakened. Furthermore, the results showed that the UV/0.005 wt.% Pt/TiO2 process was capable of e ciently decomposing gaseous DCM in air.     

Removal of copper ions from aqueous solution by calcium alginate immobilized kaolin

Kaolin has been widely used as an adsorbent to remove heavy metal ions from aqueous solutions. However, the lower heavy metal adsorption capacity of kaolin limits its practical application. A novel environmental friendly material, calcium alginate immobilized kaolin (kaolin/CA), was prepared using a sol-gel method. The e ects of contact time, pH, adsorbent dose, and temperature on Cu2+ adsorption by kaolin/CA were investigated. The Langmuir isotherm was used to describe the experimental adsorption, the maximum Cu2+ adsorption capacity of the kaolin/CA reached up to 53.63 mg/g. The thermodynamic studies showed that the adsorption reaction was a spontaneous and endothermic process.     

Removal of phosphate by Fe-coordinated amino-functionalized 3D mesoporous silicates hybrid materials

Phosphate removal from aqueous waste streams is an important approach to control the eutrophication downstream bodies of water. A Fe(III) coordinated amino-functionalized silicate adsorbent for phosphate adsorption was synthesized by a post-grafting and metal cation incorporation process. The surface structure of the adsorbent was characterized by X-ray di raction, N2 adsoropion/desoprotion technique, and Fourier transform infrared spectroscopy. The experimental results showed that the adsorption equilibrium data were well fitted to the Langmuir equation. The maximum adsorption capacity of the modified silicate material was 51.8 mg/g. The kinetic data from the adsorption of phosphate were fitted to pseudo second-order model. The phosphate adsorption was highly pH dependent and the relatively high removal of phosphate fell within the pH range 3.0–6.0. The coexistence of other anions in solutions has an adverse e ect on phosphate adsorption; a decrease in adsorption capacity followed the order of exogenous anions: F?? > SO2?? 4 > NO??3 > Cl??. In addition, the adsorbed phosphate could be desorbed by NaOH solutions. This silicate adsorbent with a large adsorption capacity and relatively high selectivity could be utilized for the removal of phosphate from aqueous waste streams or in aquatic environment.     

Removal of heavy metal ions from aqueous solution using red loess as an adsorbent

The adsorption behaviors of heavy metals onto novel low-cost adsorbent, red loess, were investigated. Red loess was characterized by X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectra. The results indicated that red loess mainly consisted of silicate, ferric and aluminum oxides. Solution pH, adsorbent dosage, initial metal concentration, contact time and temperature significantly influenced the efficiency of heavy metals removal. The adsorption reached equilibrium at 4 hr, and the experimental equilibrium data were fitted to Langmuir monolayer adsorption model. The adsorption of Cu(II) and Zn(II) onto red loess was endothermic, while the adsorption of Pb(II) was exothermic. The maximum adsorption capacities of red loess for Pb(II), Cu(II) and Zn(II) were estimated to be 113.6, 34.2 and 17.5 mg/g, respectively at 25°C and pH 6. The maximum removal efficiencies were 100% for Pb(II) at pH 7, 100% for Cu(II) at pH 8, and 80% for Zn(II) at pH 8. The used adsorbents were readily regenerated using dilute HC1 solution, indicating that red loess has a high reusability. All the above results demonstrated that red loess could be used as a possible alternative low-cost adsorbent for the removal of heavy metals from aqueous solution.