Numerical Investigation of the Effects of Boundary-Layer Evolution on the Predictions of Ozone and the Efficacy of Emission Control Options in the Northeastern United States

This paper examines the effects of two different planetary boundary-layer (PBL) parameterization schemes – Blackadar and Gayno–Seaman – on the predicted ozone (O₃) concentration fields using the MM5 (Version 3.3) meteorological model and the MODELS-3 photochemical model. The meteorological fields obtained from the two boundary-layer schemes have been used to drive the photochemical model to simulate O₃ concentrations in the northeastern United States for a three-day O₃ episodic period. In addition to large differences in the predicted O₃ levels at individual grid cells, the simulated daily maximum 1-h O₃ concentrations appear at different regions of the modeling domain in these simulations, due to the differences in the vertical exchange formulations in these two PBL schemes. Using process analysis, we compared the differences between the different simulations in terms of the relative importance of chemical and physical processes to O₃ formation and destruction over the diurnal cycle. Finally, examination of the photochemical model's response to reductions in emissions reveals that the choice of equally valid boundary-layer parameterizations can significantly influence the efficacy of emission control strategies.     

Why Should We Calculate Complex Indices of Ozone Exposure? Results from Mediterranean Background Sites

While moving towards a flux-based approach, exposure-based ozone metrics are still a practical measure for summarising ambient air quality. Ozone hourly concentrations for the period 2000–2004 from sites in the Mediterranean Italy (≤600 m a.s.l.) were examined to define the O₃ summary statistic in the area, and to determine how O₃ exposure indices correlate to each other. Thirty-four of the most common O₃ exposure metrics were calculated. The results show that background O₃ pollution in Italy exceeds the European and North American standards. The exceedances of the target value, information and alert thresholds set by the 2002/3/CE Directive should encourage Italy to take the appropriate measures to reduce the risk. All the O₃ exposure indices, except the maximum permissible ozone concentration (MPOC) for forests, point to the potential for negative effects on vegetation and human health across Italy. As indices evaluated significantly correlated with each other, we suggest use of the most biologically meaningful metric when summarizing air quality information.     

混合气液两相放电对水中有机物降解的机理研究

采用混合气液两相放电的方法来处理水中的有机物.结果表明,这种新型的水处理方法对于苯酚具有较好地去除效果．随着电压的增加和空气的通入,苯酚的去除率都有所增加. 对放电区域内产生的活性物种——过氧化氢和臭氧进行了定量的测定,并发现随着电压和空气的通入量的增加,这2种物质的量都有所增加．对于反应过程中的能耗进行分析得到随着电压的增加,能耗增加的幅度要大于苯酚降解率增加的幅度,能量效率增加较小. 空气的通入增加了能耗, 输入总能量中一部分能量使反应溶液温度升高,导致了能量的损耗.     

反应沉淀一体式矩形环流生物反应器的传氧特性研究

设计制作了一种新型的反应沉淀一体式矩形环流生物反应器,通过清水实验研究了其结构特性(环流区内导流板顶端与液面的距离,固定宽度下环流区长度变化)对反应器充氧性能、气含率、气体上升速度和液体循环速度的影响,并在优选结构的反应器中进行了模拟污水试验.结果表明,当升流区截面长度、降流区截面长度、内导流板顶部液流截面高度三者相等时,传氧性能较好,在进水COD为300～400 mg/L的情况下,污泥浓度可以稳定保持在6000 mg/L左右.     

二甲基甲酰胺环境标准浓度值研究

根据国外二甲基甲酰胺(DMF)的环境标准浓度值、美国环保局工业环境实验室和苏联学者IO.A.KPOTOB等所建立的环境标准计算公式及DMF的嗅觉阈浓度,遵循与经济、技术发展水平和相关方的承受能力相适应原则。建议DMF长期(日均)质量标准浓度值为0.1mg/m3,短期(时均)质量标准浓度值为0.15mg/m3,厂界标准浓度值为0.15mg/m3。     

油田作业废水臭氧化处理技术的实验研究

针对油田作业废水(COD)高、难降解的特点,探讨了废水的pH、COD初始浓度、臭氧投加量和臭氧化时间等因素对油田作业废水的COD去除效果的影响。结果表明,臭氧化对油田作业废水COD去除效果影响的主要因素为废水pH、废水的COD和臭氧投加量;当废水的COD为1064.0mg/L、pH为3.0、臭氧投加量为10g/L时,废水的COD去除率达到69.1%;臭氧化处理对低浓度油田作业废水的COD去除效果低于其对高浓度废水的处理效果。     

紫外光和活性炭对有机物臭氧化的协同催化作用

以城市二级出水中微量有机污染物为处理的目标物质,通过静态试验分别考察了不同催化条件下臭氧对水中有机污染物的降解效果.结果表明:协同催化反应器对水体在254 nm处紫外吸光度(E₂₅₄)的去除率达87.40%,对COD_Cr的去除率可达59.79%,对臭氧的利用率可达到91.4%,因此,254 nm紫外光和活性炭对水中微量有机污染物的臭氧化过程具有协同催化作用,并大大提高了系统对臭氧的利用率;受OH－影响,碱性条件下O₃/UV/C工艺对COD_Cr和E₂₅₄的去除效果好于中性和酸性条件;不同自由基捕捉剂对臭氧化过程的影响证明,在紫外光和活性炭的协同催化作用下,臭氧分解出以羟基自由基为主的多种氧化性自由基,因此水中有机污染物的氧化降解是多种自由基反应的结果.      

Secondary materials transfer from Japan to China: destination analysis

China has been the largest importer of secondary materials for recycling from Japan during the past decade. In this study, we analyzed the transfer of major secondary materials (plastic, steel, copper, and aluminum scrap) from Japan to China. We identified specific destinations for secondary materials, and the characteristics of secondary materials transferred to China. The major destination for the transfer of secondary materials to China is Guangdong province and part of the Huadong area (Shanghai, Zhejiang, and Jiangsu). Most scrap metal imported into China is of low quality. The destinations of most high-quality nonferrous scrap, imported as processed goods on consignment or through the transit improvement trade, are the northeast border provinces, especially Xinjiang Uighur province. The coefficients of specialization for Chinese cities were different from those for the provinces. Guangdong shows an average recycling structure for China. The structure gradually changes from south to north.     

具有特定拓扑结构的聚烯烃高分子的合成

具有特定拓扑结构的聚合物合成一直是高分子合成化学领域的一个重要研究内容，设计和合成具有特定拓扑结构的聚烯烃高分子更是进一步发掘聚烯烃这一量大面广的通用高分子材料的性能、开拓其新的应用领域的重要手段。在催化剂和聚合方法的研究取得重要进展的基础上，近年来国际上在合成不同拓扑结构（包括嵌段、接枝、梳型和星型）的聚烯烃高分子研究方面发展也较快，所合成的部分高分子亦显示出独特的功能性。本文首先综述不同拓扑结构聚烯烃高分子合成的研究现状，然后结合近期化学所在此领域的研究进展，提出独特的以苯乙烯封端反应性聚烯烃为模块构建拓扑结构聚烯烃的新思路。     

IEC61511标准及在石化行业安全管理中的应用

功能安全的定量评定技术已成为确保石化行业安全生产的重要手段。针对石化行业普遍存在的功能安全问题,笔者以国际电工学会(IEC)专门制定的功能安全评定标准IEC61508及IEC61511为指导,介绍其标准制定的背景、目的、体系结构以及如何利用标准开展石化行业安全联锁系统(Safety Instrumented System,SIS)的安全与误跳车定量分析。通过对SIS开展定量安全评估,可发现联锁功能存在的安全不足与误跳车现象,对于提高我国石化行业安全生产水平具有重要的促进作用,标准中有关寿命周期功能安全管理方法及重要的工程经验也对提高我国石化安全生产水平具有借鉴作用。