城市污水培养好氧颗粒污泥的中试研究

以城市污水为处理对象,在中试SBR反应器中接种厌氧消化污泥,经过210 d运行,培养出了平均粒径在330μm的好氧颗粒污泥.实验表明,经过前3个月较低的进水有机负荷,反应器对污染物的去除效果逐步提高并达到稳定,活性污泥中与脱氮除磷相关的微生物大量富集.运行周期缩短为6 h,污泥的沉降性能和污染物去除特性保持良好,同时污泥平均粒径开始增大.好氧颗粒污泥完全形成以后,SVI值为30 mL.g-1,污泥浓度MLSS达到8.8 g.L-1,MLVSS/MLSS增至82%,氧利用速率OUR达到5.32 mg.(min.L)-1.颗粒外层以杆状菌为主,内层主要是球菌.单个周期内颗粒污泥对COD和总磷的去除率保持在90%,氨氮几乎完全去除,出水中无硝氮和亚硝氮累积,总氮的去除率达到80%,实现了良好的同步硝化反硝化和同步脱氮除磷效果.     

高径比对猪场废水脱氮与沼气脱硫耦联反应器的影响

采用填料鼓泡塔反应器研究其高径比对猪场废水脱氮与沼气脱硫耦联过程的影响,比较了3种不同高径比(8∶1、3∶1、2∶1)反应器的废水脱氮与沼气脱硫效能.在温度30～32℃、空塔停留时间6.70 min、水力停留时间3.35 d、沼气中H2 S浓度1 414～1 838 mg.m-3、进水NO x--N浓度114～243 mg.L-1的条件下,高径比2∶1反应器的运行较稳定,且处理效果较好,硫化氢去除率平均值为96.7%,NO x--N去除率平均值达到88.7%;而高径比8∶1和3∶1反应器的运行不太稳定,硫化氢去除率的平均值分别为68.0%、80.4%,NO x--N的去除率平均值分别为89.7%、90.2%.主要是因为高径比2∶1反应器的实际气速(3.12×10-2 m.s-1)比高径比3∶1、8∶1反应器的实际气速(分别为3.62×10-2 m.s-1和6.64×10-2 m.s-1)更慢,其气液传质系数(1.79×10-5 s-1)比高径比3∶1、8∶1反应器的气液传质系数(分别为1.64×10-5 s-1和1.55×10-5 s-1)更大,传质效果更好.处理效能试验结果以及反应器流体力学特征参数均表明,高径比2∶1反应器为最适合的反应器.     

微压流化式复合生物反应器处理含酚废水效能的研究

通过连续动态试验,对新型微压流化式复合生物反应器(MP-FHBR)处理模拟苯酚废水的效能进行研究.结果表明,MP-FHBR的COD容积负荷可达4.86kg/(m3·d)、苯酚容积负荷可达1.96kg/(m3·d),出水COD低于200mg/L、出水苯酚浓度低于1mg/L,COD和苯酚去除率分别达到90%和99%以上.当苯酚容积负荷达到2.04kg/(m3·d),苯酚在反应器中逐渐累积,反应器内微生物的TTC-比脱氢酶活性下降.当MP-FHBR进水苯酚浓度为800mg/L时,最佳水力停留时间为9～10h.水力负荷对反应器沉淀池的泥水分离效果影响较大,限制了反应器的进水量,所以MP-FHBR主要适用于处理较高浓度的含酚废水.     

SRT影响MBR有机污染物去除速率研究

通过考察污泥停留时间(SRT)对膜生物反应器(MBR)和粉末活性炭膜生物反应器(PAc-MBR)降解有机物速率的影响,探讨了污泥活性与胞外聚合物(EPS)的关系.结果表明:MBR和.PAC-MBR中COD降解速率随SRT延长均呈先上升后下降的趋势,分别在39～48d和48d时达到最快,对应速率常数为2.586和3.856,PAC-MBR中COD降解速率普遍高于MBR,说明投加PAC使污泥活性提高,SRT对污泥活性影响较大;MBR和PAC-MBR中胞外聚合物质量浓度与COD降解速率常数K1变化趋势一致,且胞外聚合物质量浓度与K1呈良好正相关关系,说明系统的胞外聚合物质量浓度可以作为衡量污泥活性的指标.     

Alga-lysing bioreactor and dominant bacteria strain

Alga-lysing bacteria have been paid much attention to in recent years. In this study, the alga-lysing strain P05 which was isolated from an immobilizing biosystem was immobilized by coke and elastic filler, forming two biological reactors. The removal efficiencies of algae, NH4^＋-N and organic matter using the two reactors were studied. The results showed that strain P05 was an ideal algal-lysing bacteria strain because it was easy to be immobilized by coke and elastic filler which are of cheap, low biodegradability and the simple immobilization procedure. After 7 d filming, the biological film could be formed and the reactors were used to treat the eutrophic water. These two reactors were of stability and high effect with low cost and easy operation. The optimal hydraulic retention time （HRT） of each reactor was 4 h. The algae removal rates were 80.38% and 82.1% （in term of Chl-α） of coke reactor and filler reactor, respectively. And that of NH4^＋-N were 52.3% and 52.7%. The removal rates of CODMn were 39.03% and 39.64%. The strain P05 was identified as Bacillus sp. by PCR amplification of the 16S rRNA gene, BLAST analysis, and comparison with sequences in the GenBank nucleotide database.     

浮床水蕹菜对养殖水体中营养物的去除效果研究

为研究浮床水蕹菜对池塘养殖水质的改善效果,于2007年6月至11月,在6个2000m2的标准养殖池塘进行了中试研究.3个池塘放养常规鱼类和部分名优鱼类,并利用浮床技术在水面上种植200m2的水蕹菜（Ipomoea aquatica）,另外3个池塘放养相同重量的常规鱼类作为对照塘.实验结果显示,种植塘的渔产量为1467k...     

企业风险管理与经营效率：来自中国保险业的经验证据

本文从风险管理的视角对企业效率评估的数据包络分析技术进行了改进,探讨了风险管理与经营效率的内在关联,并以中国保险业为例,对1999年以来企业真实的经营效率水平进行了评估。结果表明：企业内部的风险管理能力对其经营效率水平的提升具有明显的影响,而且这种影响力正在逐渐加强。不考虑企业内部的风险管理水平将直接导致其经营效率的测算结果出现低估,2002年以后这种低估的程度越发明显,这可归因于同期保险企业开始逐渐重视提高自身的风险管理能力。以上结论也为企业如何在管控风险的同时提升经营效率水平提供了有价值的指导。     

一株嗜盐聚磷菌的筛选及除磷性能初探

从运行稳定的以生活污水为碳源的污泥中富集分离,并筛选出一株嗜盐聚磷菌qdp05,通过对菌株的形态、生理生化特征及16SrDNA序列进行分析后,鉴定该菌株qdp05为肠杆菌属.当碳源为乙酸钠,盐度为2%的条件下,好氧条件下培养48h后,qdp05对磷的最终去除率为87.8%.在厌氧好氧连续培养过程,qdp05表现出明显的...     

Sustainability issues in sheet metal forming processes: an overview

Environmental sustainability in manufacturing is nowadays an urgent and remarkable issue and the main concerns are related to more efficient use of materials and energy.In sheet metal forming processes there is still a lack of knowledge in this field mainly due to the need of a proper modelling of sustainability issues and factors to be taken into account. The aim of this paper is mainly to underline the state of the art from a forming point of view about the sustainability contributions offered in any phase of a product life cycle. Actually, a lack in terms of comprehensive contributions is present in the technical literature, thus, the authors try to give a sort of holistic vision aimed to provide basic guidelines in order to help in identifying the possible solutions with regard to all the phases of a forming product life cycle. The main attention was paid to sheet metal forming technologies. The paper gives an overview of the main topics concerning sheet metal forming problems related to energy and resource efficiency with the aim to stress the principal contributions which may derive from such processes to environmental performances of manufacturing.     

1株脱氮除磷菌的筛选及其特性研究

采用YG培养基,结合蓝白斑筛选、异染粒染色及好氧除磷能力检测等实验,从城市生活污水处理厂好氧生化池的活性污泥中分离出7株好氧除磷菌;再经硝酸盐还原产气和缺氧培养实验,筛选出1株高效脱氮除磷菌;通过16S rRNA基因同源性比较和生理生化鉴定,初步将其鉴定为Pseudomonas grimontii,命名为C18.菌株C18在好氧培养24h后,培养基中上清液磷浓度从38.7mg/L降低到2.28mg/L,除磷率达94.1%.C18在缺氧培养24h后,培养基中上清液磷浓度从44.5mg/L降低到5.21mg/L,除磷率达88.3%;上清液硝酸盐氮浓度从184.2mg/L降低到30.6mg/L,脱氮率达83.4%.菌株C18最适脱氮除磷温度为30℃;最适脱氮除磷pH为7.5.