Pyrolysis technologies for municipal solid waste: A review

Pyrolysis has been examined as an attractive alternative to incineration for municipal solid waste (MSW) disposal that allows energy and resource recovery; however, it has seldom been applied independently with the output of pyrolysis products as end products. This review addresses the state-of-the-art of MSW pyrolysis in regards to its technologies and reactors, products and environmental impacts. In this review, first, the influence of important operating parameters such as final temperature, heating rate (HR) and residence time in the reaction zone on the pyrolysis behaviours and products is reviewed; then the pyrolysis technologies and reactors adopted in literatures and scale-up plants are evaluated. Third, the yields and main properties of the pyrolytic products from individual MSW components, refuse-derived fuel (RDF) made from MSW, and MSW are summarised. In the fourth section, in addition to emissions from pyrolysis processes, such as HCl, SO₂ and NH₃, contaminants in the products, including PCDD/F and heavy metals, are also reviewed, and available measures for improving the environmental impacts of pyrolysis are surveyed. It can be concluded that the single pyrolysis process is an effective waste-to-energy convertor but is not a guaranteed clean solution for MSW disposal. Based on this information, the prospects of applying pyrolysis technologies to dealing with MSW are evaluated and suggested.     

Nitrogen evolution during the co-combustion of hydrothermally treated municipal solid waste and coal in a bubbling fluidized bed

Nitrogen evolution was studied during the co-combustion of hydrothermally treated municipal solid wastes (HT MSW) and coal in a bubbling fluidized bed (BFB). HT MSW blending ratios as 10%, 20% and 30% (wt.%) were selected and tested at 700, 800, 900 °C. Emissions of NO and N₂O from blends were measured and compared with the results of mono-combustion trials. Moreover, concentrations of precursors like NH₃ and HCN were also quantified. The results are summarized as follows: NO emissions were predominant in all the cases, which rose with increasing temperature. The blending of HT MSW contributed to the NO reduction. N₂O emissions decreased with temperature rising and the blending of HT MSW also presented positive effects. At 30% HT MSW addition, both NO and N₂O emissions showed the lowest values (391.85 ppm and 55.33 ppm, respectively at 900 °C). For the precursors, more HCN was detected than NH₃ and both played important roles on the gas side nitrogen evolution.     

Alternative management structures for municipal waste collection services: The influence of economic and political factors

Identifying and characterising the factors that determine why a local authority opts for a particular way of managing its waste collection service is an important issue, warranting research interest in the field of municipal solid waste (MSW) management. This paper presents empirical evidence spanning a broad time horizon (2002–2010) showing that economic and political factors impact in different ways on the provision of waste management services. We examine five alternatives in this area, including public and private service delivery formulas and, within each field, individual and joint options. Our findings highlight the importance of the service cost and that of the various indicators of fiscal stress as determinant factors of management decisions regarding the provision of MSW management services.     

CFD simulation of MSW combustion and SNCR in a commercial incinerator

A CFD scheme was presented for modeling municipal solid waste (MSW) combustion in a moving-grate incinerator, including the in-bed burning of solid wastes, the out-of-bed burnout of gaseous volatiles, and the selective non-catalytic reduction (SNCR) process between urea (CO(NH₂)₂) and NO_x. The in-bed calculations provided 2-D profiles of the gas–solid temperatures and the gas species concentrations along the bed length, which were then used as inlet conditions for the out-of-bed computations. The over-bed simulations provided the profiles of incident radiation heat flux on the top of bed. A 3-dimensional benchmark simulation was conducted with a 750 t/day commercial incinerator using the present coupling scheme incorporating with a reduced SNCR reduction mechanism. Numerical tests were performed to investigate the effects of operating parameters such as injection position, injection speed and the normalized stoichiometric ratio (NSR) on the SNCR performance. The simulation results showed that the distributions of gas velocity, temperature and NO_x concentration were highly non-uniform, which made the injection position one of the most sensitive operating parameters influencing the SNCR performance of moving grate incinerators. The simulation results also showed that multi-layer injections were needed to meet the EU2000 standard, and a NSR 1.5 was suggested as a compromise of a satisfactory NO_x reduction and reasonable NH₃ slip rates. This work provided useful guides to the design and operation of SNCR process in moving-grate incinerators.     

锆-十六烷基三甲基氯化铵改性活性炭对水中硝酸盐和磷酸盐的吸附特性

采用锆(Zr)和阳离子表面活性剂十六烷基三甲基氯化铵(CTAC)对活性炭进行联合改性,考察了所制备的Zr-CTAC改性活性炭对水中硝酸盐和磷酸盐的吸附去除作用,并探讨了相关的吸附去除机制.结果表明,Zr-CTAC改性活性炭对水中硝酸盐和磷酸盐均具备较好的吸附去除能力.Zr-CTAC改性活性炭对硝酸盐和磷酸盐吸附动力学过程满足准二级动力学模型.Langmuir、Freundlich和Dubinin-Radushkevich(D-R)等温吸附模型可以较好地描述Zr-CTAC改性活性炭对水中硝酸盐的等温吸附过程,Langmuir和D-R等温吸附模型可以较好地描述Zr-CTAC改性活性炭对水中磷酸盐等温吸附过程,通过Langmuir模型计算得到吸附剂对硝酸盐和磷酸盐的最大单位吸附量分别为7.58 mg·g-1和10.9 mg·g-1.高的p H会抑制Zr-CTAC改性活性炭对水中硝酸盐和磷酸盐的吸附.水中共存的Cl-、HCO-3和SO2-4等阴离子均会抑制Zr-CTAC改性活性炭对硝酸盐和磷酸盐的吸附,且对吸附硝酸盐的抑制作用较强而对吸附磷酸盐的抑制作用较弱.水中共存的磷酸盐对Zr-CTAC改性活性炭吸附硝酸盐的抑制作用较强,而水中共存的硝酸盐对Zr-CTAC改性活性炭吸附磷酸盐的抑制作用较弱.1 mol·L-1Na Cl溶液可以使90%左右被吸附到Zr-CTAC改性活性炭表面上的硝酸盐解吸下来.1 mol·L-1的Na OH溶液可以使78%左右被吸附到Zr-CTAC改性活性炭表面上的磷酸盐解吸下来.Zr-CTAC改性活性炭对硝酸盐的吸附机制主要包括阴离子交换作用和静电吸引作用,对磷酸盐的吸附机制主要包括配位体交换作用、阴离子交换作用和静电吸引作用.上述结果说明Zr-CTAC改性活性炭适合作为一种吸附剂去除废水中的硝酸盐和磷酸盐.     

高含固污泥厌氧消化中Fe/S及pH对原位抑硫效率影响及其交互作用

以城市污水处理厂高含固污泥为对象,分别进行了连续厌氧消化抑硫试验和消化污泥Fe(Ⅲ)投加抑硫试验,探讨不同Fe/S(摩尔比)对污泥厌氧消化中溶解态硫化物去除效率的影响以及Fe(Ⅲ)与pH的交互作用.结果表明,热水解污泥厌氧消化采用原位抑硫技术,在Fe/S(摩尔比)为7.75时沼气中H_2S含量可由170.4×10~(-6)降至14.09×10~(-6),无需进行后续处理;当pH为7.00~7.50、Fe/S为1~11时,pH为原位抑硫主要显著影响因子,提高消化池pH有利于降低Fe(Ⅲ)投加量;高含固污泥厌氧消化沼气满足H_2S利用标准时,所需最低Fe/S为7.0;当消化池pH低于7.30时,将无法通过调节Fe/S实现H_2S浓度达标排放.     

Metal distribution characteristic of MSWI bottom ash in view of metal recovery

Bottom ash is the major by-product of municipal solid waste incineration(MSWI), and is often reused as an engineering material, such as road-base aggregate. However, some metals(especially aluminum) in bottom ash can react with water and generate gas that could cause expansion and failure of products containing the ash; these metals must be removed before the ash is utilized. The size distribution and the chemical speciation of metals in the bottom ash from two Chinese MSWI plants were examined in this study, and the recovery potential of metals from the ash was evaluated. The metal concentrations in these bottom ashes were lower than that generated in other developed countries. Specifically, the contents of Al,Fe, Cu and Zn were 18.9–29.2, 25.5–32.3, 0.7–1.0 and 1.6–2.5 g/kg, respectively. Moreover,44.9–57.0 wt.% of Al and 55.6–75.4 wt.% of Fe were distributed in bottom ash particles smaller than 5 mm. Similarly, 46.6–79.7 wt.% of Cu and 42.9–74.2 wt.% of Zn were concentrated in particles smaller than 3 mm. The Fe in the bottom ash mainly existed as hematite, and its chemical speciation was considered to limit the recovery efficiency of magnetic separation.     

添加动物源氨基酸水解液研制生物有机肥

为改善生物有机肥性质,提高生物有机肥质量,采取在生物有机肥中添加外源氨基酸水解液以提升生物有机肥中功能微生物的数量.以病死猪酸解制得氨基酸水解液为生物有机肥外加原料,研究了氨基酸水解液添加量、有机肥种类（鸡粪、牛粪、中药渣）、发酵时间对功能菌株SQR9数量的影响.结果表明:当氨基酸水解液添加量为20%时固体发酵效果优于其他接种量,预发酵3 d后接种SQR9的功能菌数量明显高于未预发酵直接接菌,预发酵中肥料（以干质量计,下同）的最高功能菌数量可达4×108 CFU/g,而第0天接菌时肥料的最高功能菌数量仅为1.2×108 CFU/g.以腐熟鸡粪、牛粪、中药渣堆肥为载体,添加酸解氨基酸研制生物有机肥的最优接菌量分别为10.0%、7.5%、10.0%;SQR9菌株生长的最佳含水量为40%.此外,氨基酸水解液的添加可提高生物有机肥的w（TN）.研究显示,氨基酸水解液的添加能有效促进固态发酵过程中功能菌株数量的增加.      

港口罢工对周边空气质量的影响

港口污染物的排放浓度极大地影响着周边的空气质量,以2013年3月28日香港国际集装箱码头发生的罢工事件为契机来探究港口运作短暂的瘫痪对周边空气质量的影响。首先,进行污染物之间的相关性分析确定影响本次罢工事件的污染物主要为NO_2、NO_x、SO_2以及O_3。其次,基于罢工前、罢工期间以及罢工后污染物排放的浓度变化,进行横向对比发现罢工期间的污染物确实有一定程度的减少。再次,利用纵向对比排除四季带来的影响探究不同年份同一阶段污染物浓度的变化情况评估罢工期间的空气质量。最后,以NO_2为例建立预测模型对罢工期间的NO_2浓度进行预测,根据实际值与预测值之间的差异来说明罢工影响了NO_2的预测趋势。这项研究主要强调港口空气质量对整个环境的影响,在一定程度上说明政府实施政策的有效性,为政府提供了决策支持,同时也要注重污染物之间的相互转化作用对环境的影响。     

厌氧发酵处理庆大霉素菌渣的可行性及条件优化

采用厌氧发酵处理庆大霉素菌渣,考察了含固率、接种比、接种污泥、发酵底物等因素对庆大霉素菌渣厌氧发酵的影响,并用累积净甲烷产量衡量庆大霉素菌渣进行厌氧发酵的可行性及发酵程度。试验结果证实了庆大霉素菌渣进行厌氧发酵的可行性,其中含固率和接种比对发酵的影响较大,最佳条件为含固率5%,接种比1/3;对比试验所用3种接种污泥,发现接种某造纸厂污水处理IC反应器的厌氧颗粒污泥效果最优,在最优含固率和接种比的条件下,累积净产甲烷量为28.21 m3/t;此外,试验还证实,采用不同菌渣的联合发酵表现出了明显的协同作用,在最优条件下,庆大霉素菌渣与林可霉素菌渣按1∶2的比例联合发酵的产甲烷量可达到37.5 m3/t。