Recovery of solid fuel from municipal solid waste by hydrothermal treatment using subcritical water

Hydrothermal treatments using subcritical water (HTSW) such as that at 234 °C and 3 MPa (LT condition) and 295 °C and 8 MPa (HT condition) were investigated to recover solid fuel from municipal solid waste (MSW). Printing paper, dog food (DF), wooden chopsticks, and mixed plastic film and sheets of polyethylene, polypropylene, and polystyrene were prepared as model MSW components, in which polyvinylchloride (PVC) powder and sodium chloride were used to simulate Cl sources.While more than 75% of carbon in paper, DF, and wood was recovered as char under both LT and HT conditions, plastics did not degrade under either LT or HT conditions. The heating value (HV) of obtained char was 13,886-27,544 kJ/kg and was comparable to that of brown coal and lignite. Higher formation of fixed carbon and greater oxygen dissociation during HTSW were thought to improve the HV of char.Cl atoms added as PVC powder and sodium chloride to raw material remained in char after HTSW. However, most Cl originating from PVC was found to converse into soluble Cl compounds during HTSW under the HT condition and could be removed by washing.From these results, the merit of HTSW as a method of recovering solid fuel from MSW is considered to produce char with minimal carbon loss without a drying process prior to HTSW. In addition, Cl originating from PVC decomposes into soluble Cl compound under the HT condition. The combination of HTSW under the HT condition and char washing might improve the quality of char as alternative fuel.     

Comparing the greenhouse gas emissions from three alternative waste combustion concepts

Three alternative condensing mode power and combined heat and power (CHP) waste-to-energy concepts were compared in terms of their impacts on the greenhouse gas (GHG) emissions from a heat and power generation system. The concepts included (i) grate, (ii) bubbling fluidised bed (BFB) and (iii) circulating fluidised bed (CFB) combustion of waste. The BFB and CFB take advantage of advanced combustion technology which enabled them to reach electric efficiency up to 35% and 41% in condensing mode, respectively, whereas 28% (based on the lower heating value) was applied for the grate fired unit. A simple energy system model was applied in calculating the GHG emissions in different scenarios where coal or natural gas was substituted in power generation and mix of fuel oil and natural gas in heat generation by waste combustion. Landfilling and waste transportation were not considered in the model. GHG emissions were reduced significantly in all of the considered scenarios where the waste combustion concepts substituted coal based power generation. With the exception of condensing mode grate incinerator the different waste combustion scenarios resulted approximately in 1 Mton of fossil CO₂-eq. emission reduction per 1 Mton of municipal solid waste (MSW) incinerated. When natural gas based power generation was substituted by electricity from the waste combustion significant GHG emission reductions were not achieved.     

甘氨酸母液脱色废活性炭的微波-Fenton试剂氧化法再生

采用微波-Fenton试剂氧化法对甘氨酸母液脱色过程中产生的废活性炭进行再生,考察了废活性炭再生率的影响因素,并用SEM对再生活性炭进行了表征.实验结果表明,在Fenton试剂中n(H2O2)∶n(Fe2+)为24∶1、H2O2的浓度为25 mmol/L、溶液pH为3、反应温度为55℃、反应时间为18 min、微波功率为600 W时,废活性炭的再生率可达到75.80％.     

响应面法优化阴阳极同时作用电化学法处理染料废水

在自制电化学反应器中,以甲基橙模拟染料废水为处理对象,采用Box-Behnken Design响应面法研究了影响阴阳极同时作用电化学法处理染料废水的因素及其交互作用。实验得出各因素对废水脱色率影响的大小顺序为：电流密度> Fe³⁺浓度>Cl^-浓度。各因素之间的交互作用对废水脱色率影响的大小顺序为：电流密度和Fe³⁺浓度>电流密度和Cl^-浓度>Fe³⁺浓度和Cl^-浓度。优化结果表明：Fe³⁺浓度为1.02 mmol/L、Cl^-浓度为10.96 mmol/L、电流密度为11.52 mA/cm²时,最佳脱色率为94.67%。阴阳极同时作用电化学法对甲基橙去除效果显著。     

MnOx/TiO2催化剂催化燃烧去除废气中的正己烷

采用溶胶-凝胶法制备了MnOx/TiO2催化剂,考察了n(Mn):n(Ti)、催化剂载体、气体流量对催化燃烧去除废气中正己烷效果的影响.实验结果表明:随着n(Mn):n(Ti)的增加,正己烷去除率先增加后减小,气体流量减小正己烷去除率增大;当n (Mn):n(Ti)为7.85％、气体流量为100 mL/min时,在240℃时正己烷的去除率为90％,MnOx/TiO2催化活性最大;MnOx/TiO2的催化活性优于MnOx/SiO2;SEM和XRD表征结果表明,所制备的MnOx/TiO2是一种活性物种MnOx高度分散的纳米结构催化剂.     

罐底油泥特性分析及其除油处理工艺

通过研究罐底油泥的理化性质,开发了适于处理罐底油泥的系列工艺:先采用调质技术提高罐底油泥流动性;再采用超声破乳降低油泥稳定性,改善油泥分离性能;最后采用卧式离心机对油泥进行离心分离处理.在复合型清洗剂加入量为800 mg/L、超声温度为60℃、超声功率为12 kW、超声时间为25 min、离心温度为60℃、絮凝剂加入量为600 mg/L、离心机转速为2200 r/min的条件下,系统稳定运行9d,离心机出口泥中含油率低于2.00％,水中悬浮固体质量浓度低于170 mg/L,达到了对罐底油泥进行除油的目的.     

氯酸钠氧化盐酸酸洗废液制备聚氯化铁

钢材在深加工过程中通常使用盐酸对其表面进行酸洗除锈,从而产生大量废液。为了实现盐酸酸洗废液的资源化处理,以氯酸钠作为氧化剂制备聚氯化铁,考察了氧化剂加入量、浓盐酸加入量、反应时间、反应温度等因素对Fe²⁺转化率的影响。实验得到的最佳工艺条件为：每处理100 mL废液需加入7.0 g氯酸钠、12 mL浓盐酸（12 mol/L）、0.3 g磷酸二氢钾,反应温度30 ℃,反应时间30 min,搅拌转速5 r/s。该条件下,Fe²⁺转化率可达98.51%,得到的聚氯化铁产品符合《水处理剂 聚氯化铁》（HG/T 4672—2014）标准。     

冷轧乳化液废水处理试验研究

对武钢冷轧乳化液废水采用超滤和氧化破乳法进行对比试验,从试验运行效果、投资费用、运行成本等方面进行了比较分析,得出处理冷轧乳化液废水的最佳方法－超滤法。对冶金行业乳化液废水的处理具有一定的参考价值。     

游泳池循环水抑藻方法研究

本研究采用氯化混凝技术 ,有效地抑制了游泳池水中藻类生长。经此技术处理后的游泳池水清澈透明 ,达到卫生部颁布的《游泳场所卫生标准》的要求 ,既节约水资源 ,又避免污染环境 ,具有广阔的应用前景。     

利用纯碱厂碱性废液进行烟气脱硫(FGD)工艺试验研究

纯碱厂在生产纯碱过程中要排放出大量碱性废液 ,如果利用其作为净化锅炉烟气的脱硫剂 ,不仅减低了脱硫剂费用 ,而且消除了SO2 污染。本文在简单分析旋流板塔式除尘脱硫装置的结构和工作原理的基础上 ,探讨了利用碱性废液进行烟气除尘脱硫的主要影响因素 ,并找出了最佳操作条件。试验结果表明 :利用纯碱厂排放的碱性废液———一次盐泥进行锅炉烟气脱硫可以取得较高的净化效率 ,同时解决了因为碱性废液排放而给周围水域带来的污染。旋流板塔式除尘脱硫装置结构简单 ,脱硫效率高 ,并且运行安全稳定 ,是一项值得推广的技术