乙醇汽油与普通汽油非常规污染物排放特性对比研究

在一台满足国Ⅴ排放标准的双喷射(气口喷射+缸内直喷)汽油机上开展了燃用E10乙醇汽油(乙醇体积比为10%)对发动机非常规排放特性影响的试验研究.使用傅里叶变换红外分析仪(FTIR)测量了饱和烃、不饱和烃、芳香烃及醇、醛等非常规污染物排放量,对比分析了双喷射模式时各工况下E0和E10两种燃料的非常规排放水平.结果表明,双喷射模式下,加入乙醇有效降低了乙烯、1,3-丁二烯、苯和甲苯的排放量,但会导致乙醛排放升高.双喷射模式下,随着负荷增加,两种燃料下的1,3-丁二烯和甲苯排放呈现先升高后降低的趋势,乙烯、甲醛和苯排放则先降低后升高.乙醇能抑制1,3-丁二烯、乙烯生成,抑制效果为PFI模式优于双喷射模式,GDI模式抑制量最低.PFI和GDI模式下E10的甲醛排放均显著升高,但双喷射模式有效抑制了甲醛排放的增加.     

南京和北京气溶胶光学厚度与PM2.5质量浓度关系对比分析

利用南京与北京地区2014年5月1日—2019年10月31日的PM_2.5监测数据、气溶胶光学厚度观测资料以及同期MICAPS地面气象要素的观测资料,对两地PM_2.5浓度的变化规律及其与气溶胶光学厚度、气象要素的关系进行了分析和讨论,结果表明：南京与北京均呈现PM_2.5浓度冬季显著高于夏季,AOD冬季小于夏季的特征;对比而言,北京PM_2.5月均浓度高于南京地区;南京与北京的PM_2.5浓度与AOD均为正相关关系,PM_2.5浓度与AOD间相关性存在显著的季节差异,主要表现为夏季相关性大于冬季相关性;两地AOD与PM_2.5浓度均为正相关关系,在同一AOD水平下,相对湿度越大,PM_2.5浓度越大,气溶胶吸湿增长易造成污染物积累;南京PM_2.5浓度与能见度的r为0.57,而北京的r为0.83,两地的PM_2.5浓度与能见度的冬季相关性较夏季好,在高相对湿度下,同一PM_2.5浓度水平时,南京能见度较北京好.     

临沂市区主要大气污染物的污染特征及其对居民健康的影响

大气污染是全球性的公共环境健康问题.本研究基于临沂市区2015年6种大气污染物（PM_2.5、PM₁₀、SO₂、NO₂、CO、O₃）的逐日监测数据,分析了污染物的污染特征及其与气象因子的相关性,通过构建广义相加模型,模拟分析了单个污染物与居民呼吸、循环系统疾病门诊人次的暴露-反应关系.结果表明,PM_2.5和PM₁₀是临沂市区首要大气污染物,NO₂和SO₂次之,O₃和CO浓度较低;除O₃外,其它5种污染物之间呈显著正相关,与风速、温度、相对湿度3个气象因子呈负相关,浓度水平冬季高、夏季低;O₃与温度呈显著正相关.对于呼吸系统疾病,单个污染物每增加10 μg·m^-3（CO每增加0.1 mg·m^-3）的最大效应情况是：PM₁₀、SO₂、NO₂、CO均在当天（lag0）使得门诊人次分别增加0.36%、1.77%、1.29%、0.69%,PM_2.5和O₃分别在累积滞后6 d（lag05）和单日滞后3 d（lag3）使得门诊人次分别增加0.6%和1.07%;对于循环系统疾病,单个污染物每增加10 μg·m^-3（CO每增加0.1 mg·m^-3）的最大效应是：PM_2.5、PM₁₀均在累积滞后5 d（lag04）使得门诊人次分别增加0.72%、0.80%,SO₂、NO₂均在累积滞后6 d使得门诊人次分别增加3.55%、3.54%,CO和O₃则分别在当天和单日滞后3 d使得门诊人次分别增加0.77%、1.39%.对于呼吸、循环系统疾病,PM_2.5、PM₁₀、CO、O₃对男性的影响均大于女性,SO₂则反之;NO₂对男性呼吸系统和女性循环系统影响较大.大气污染物对少年（7~17岁）呼吸系统和对中年（41~65岁）循环系统影响较大.临沂市区6种大气污染物存在不同程度的污染,对居民呼吸、循环系统疾病均有不同程度的影响,且存在性别和年龄的差异.     

2006—2018年中国省级以上开发区的空间分布特征变化

以新的国土空间规划语境为背景,基于核密度估计、标准差椭圆法和分类统计对我国2006—2018年省级以上开发区的密度分布特征变化、发展重心轴向的变化和主体功能区视角下的分布变化做了分析。研究表明：该阶段我国省级以上开发区空间分布的东西差距得到一定缓解,仍存在东部连片集聚、西部据点集中的模式差异。开发区分布的总体重心已经向西北方向移动,发展轴向则由原来的南北轴向转向了东南—西北轴向。从主体功能区视角来看,开发区空间分布格局呈现出外围扩散与局部缩减的动态调整。开发区规模的增长主要集中在重点开发区域,缩减主要发生在生态功能区域。这些新变化将为我国国土空间土地利用优化和国土空间管控实践提供重要参考。     

大辽河沉积物中微塑料的污染特征

以大辽河为研究对象,选取8个典型区域的沉积物,采用密度浮选法,结合体视显微镜及μ-FTIR,进行大辽河沉积物中微塑料的组成及分布特征研究.结果表明,大辽河沉积物微塑料平均丰度为（66.67±79.93）个/kg;其中位于鞍山海城市的DL5丰度最高,为（193.33±172.43）个/kg,辽阳县柳壕镇的DL6丰度最低,为（20.00±34.64）个/kg;微塑料颜色以白色、黑色、黄色为主（83.75%）,形状以纤维、薄膜、碎片为主（91.25%）,粒径以（1000~2000）μm为主（33.75%）.通过红外光谱分析可得出,大辽河沉积物中薄膜类微塑料的主要成分是聚酰胺（PA）、聚丙烯（PP）和聚乙烯（PE）,碎片类的主要成分是聚乙烯（PE）和聚丙烯（PP）,泡沫类和颗粒类的主要成分是聚苯乙烯（PS）,纤维类的主要成分是人造丝（RY）及聚对苯二甲酸乙二醇酯（PET）.总体上,该研究区域沉积物中微塑料的丰度处于中等偏低水平.本研究可为我国淡水河流沉积物中微塑料的污染分布研究提供基础科学数据.     

红树林土壤解磷菌的分离鉴定及解磷特性

从罗源湾红树林根际土壤中分离解磷菌,筛选出洋葱伯克霍尔德菌（Burkholderia cepacia, NR 113645.1）和短小芽孢杆菌（Bacillus pumilus, NR 043242.1）,研究它们的解磷特性和动态解磷过程. HPLC结果表明, B. cepacia菌液上清中含葡萄糖酸、丙酮酸、乳酸、乙酸、丁二酸, 这些有机酸的产生导致磷酸盐溶解. B.pumilus菌液上清中仅检测到少量的葡萄糖酸, 因此该菌溶磷效果不佳. 在细菌动态溶磷过程中发现, 经B. cepacia菌处理的磷酸钙, 其X射线衍射（XRD）特征峰强度随时间的增长降低, 显微镜图像显示磷酸钙颗粒随时间增长变小, 甚至消失. 而经B.pumilus菌处理的结果表明, 在试验期间内磷酸钙峰强度和颗粒大小没有明显变化. 细菌产生有机酸是溶解磷酸盐的重要前提, 这是解决板结土壤中难溶性磷源转化为生物可利用磷源问题的关键.     

2018年春节期间京津冀地区污染过程分析

为了解2018年春节期间京津冀地区空气污染情况,利用近地面污染物浓度数据、激光雷达组网观测数据,结合WRF气象要素、颗粒物输送通量和HYSPLIT气团轨迹综合分析污染过程.结果表明,春节期间出现3次污染过程.春节前一次污染过程,各站点PM_2.5浓度均未超过200μg/m³;除夕夜,廊坊站点PM_2.5峰值浓度达到504μg/m³,是清洁天气的26倍;年初二~初五,各站点PM_2.5始终高于120μg/m³,且污染主要聚集在500m高度以下,北京地区存在高空传输,800m处最大输送通量达939μg/（m³·s）,此次重污染过程为一次典型的区域累积和传输过程.京津冀地区处于严格管控状态时,燃放烟花爆竹期间PM_2.5峰值浓度可达无燃放时PM_2.5峰值的3.2倍.为防止春节期间重污染现象的发生,需对静稳天气下燃放烟花炮竹采取预防对策.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Density functional theory (DFT) studies of vanadium-titanium based selective catalytic reduction (SCR) catalysts

Based on density functional theory (DFT) and basic structure models, the chemical reactions on the surface of vanadium-titanium based selective catalytic reduction (SCR) denitrification catalysts were summarized. Reasonable structural models (non-periodic and periodic structural models) are the basis of density functional calculations. A periodic structure model was more appropriate to represent the catalyst surface, and its theoretical calculation results were more comparable with the experimental results than a non-periodic model. It is generally believed that the SCR mechanism where NH₃ and NO react to produce N₂ and H₂O follows an Eley-Rideal type mechanism. NH₂NO was found to be an important intermediate in the SCR reaction, with multiple production routes. Simultaneously, the effects of H₂O, SO₂ and metal on SCR catalysts were also summarized.     

Recent advances in catalytic decomposition of ozone

Ozone (O₃), as a harmful air pollutant, has been of wide concern. Safe, efficient, and economical O₃ removal methods urgently need to be developed. Catalytic decomposition is the most promising method for O₃ removal, especially at room temperature or even subzero temperatures. Great efforts have been made to develop high-efficiency catalysts for O₃ decomposition that can operate at low temperatures, high space velocity and high humidity. First, this review describes the general reaction mechanism of O₃ decomposition on noble metal and transition metal oxide catalysts. Then, progress on the O₃ decomposition performance of various catalysts in the past 30 years is summarized in detail. The main focus is the O₃ decomposition performance of manganese oxides, which are divided into supported manganese oxides and non-supported manganese oxides. Methods to improve the activity, stability, and humidity resistance of manganese oxide catalysts for O₃ decomposition are also summarized. The deactivation mechanisms of manganese oxides under dry and humid conditions are discussed. The O₃ decomposition performance of monolithic catalysts is also summarized from the perspective of industrial applications. Finally, the future development directions and prospects of O₃ catalytic decomposition technology are put forward.