压力板仪法测土-水特征曲线试验研究

非饱和土土-水特征曲线(SWCC)表示了土中含水量与吸力之间的关系。针对非饱和土干-湿循环过程中的吸力变化特征,开展试验研究。采用体积压力板仪实现非饱和土的脱湿和吸湿过程。试验成果显示:(1)土-水特征曲线是不稳定的,它与土体含水率的变化路径有关;(2)在干湿循环过程中,相同的基质吸力具有不同的含水量。     

海上含聚污水电化学处理装置的优化

为解决传统电化学方法在含聚污水处理时电极板消耗严重、絮渣量大的问题,通过改进电极板材料、组合数及结构等,研究适度降解-除油一体化电化学技术,在降低渣泥量的同时保证处理效果。实验结果表明:最佳电极板组合为"网状惰性金属复合物极板(阳)-网状铝极板(阴)-网状铝极板(阴)-网状惰性金属复合物极板(阳)";在电解电流为4.0 A、极板间距为8.0 cm、面体比(电极板面积与处理污水量的比值)为2/17 cm~2/mL、电解时间为30 min的最佳处理条件下,几乎无絮渣产出,含聚污水的浊度去除率为93.3%、聚合物降解率为92.0%、除油率为95.0%,展现了优良的处理效果。     

异波折板水解酸化-A~2O一体化反应器实验研究

设计了异波折板水解酸化-A2O一体化反应器,进行生活污水处理的实验研究。10个月的实验结果表明,系统的最佳水力停留时间(HRT)为8 h时,最适COD进水浓度为240~600 mg/L,最佳混合液回流比(r)-污泥回流比(R)为250%~100%。控制反应器于以上运行参数下,25±2℃所对应的COD、TN和TP去除率分别为96.84%、67.55%和81.92%。当温度降至7℃时,其COD、TP和TN分别降至86.35%、50.25%和65.68%。基于实验分析结果,阐明了一体化反应器高效性的机理在于异波折板水解酸化段具有高效传质特性和A2O段具有复合式活性污泥-接触氧化好氧池的特点。     

好氧活性污泥中自养硝化细菌分离方法研究

分别采用琼脂平板、琼脂糖平板、水洗洋菜平板和硅胶平板分离培养城市污水处理厂好氧活性污泥中的硝化细菌。在相同的培养条件下,琼脂平板和水洗洋菜平板有杂菌生长;硅胶平板制作过程繁琐,培养后期出现失水性干裂;琼脂糖平板没有杂菌生长。通过对分离菌株的表观形态观察和NorB基因检测鉴定分离菌株,证明琼脂糖分离出了目的菌株,适合生长周期长的自养硝化细菌分离培养。     

微电解/斜板沉淀/生物接触氧化处理印刷电路板废水

根据某印刷电路板企业生产废水的水质特点,对废水进行分类收集处理后,采用微电解/斜板沉淀/生物接触氧化工艺处理综合废水。工程运行结果表明,该工艺处理效果稳定,出水水质符合《污水综合排放标准》(GB 8978-1996)的一级排放标准。     

韶钢新石灰窑烟气除尘技术的应用

韶钢新石灰窑烟气除尘系统要用旋风除尘器、金属管式换热器、高效陶瓷多管除尘器的组合方式。介绍了该系统的设计参数、工艺流程、主要设备及其功能。     

掘进巷道粉尘控制技术的研究

针对掘进巷道的特点,研制了一种高效实用的自激式水浴水膜除尘器,并对其结构、除尘过程和与掘进机相配套的方式进行了研究分析。还对掘进巷道中的产尘源进行了调查和分析,认为掘进巷道的防尘方法：应先采用掘进机头的内外喷雾,然后采用长压短抽的通风除尘系统和利用除尘器将含尘空气进行净化;对转载点除尘采用简易闭密罩加喷雾;对巷道周壁的粉尘采用喷洒粘尘剂固尘,才能有效地降低整个巷道的粉尘浓度。     

考虑油滴碰撞聚结的斜板除油过程模拟

考虑离散油滴在油田废水除油过程中发生的油滴碰撞聚结现象,模拟得出斜板除油器内全部油滴的动态信息,用于斜板除油器除油效率的计算.对矩形同向流斜板除油过程的模拟研究表明:油滴的碰撞聚结会增加斜板除油的效率;当废水的原始含油浓度增大时,斜板除油的效率会增大,碰撞聚结对除油效率提高的影响也越大;废水流动速度提高及斜板的倾斜角度增加均会使斜板的除油效率降低,但此时油滴碰撞聚结对除油效率的影响仍很明显.     

一起预制板脆性断裂事件的原因及预防

对发生在该钢铁厂的一起预制板脆性断裂事件进行了介绍和分析,探讨了在高温条件下发生断裂的原因。     

Influence of sewage culvert cover plate thickness on dynamic response and damage of the cover plate under gas explosion

In order to address the risk of combustible gas explosions in sewage culverts, a numerical model was established using ANSYS/LS-DYNA software. The model consisted of a culvert and a cover plate, and was used to study the effect of cover plate thickness (ranging from 0.08 m to 0.12 m) on the dynamic response and damage of the structure under explosive loads. The results indicated that, during the loading negative pressure stage, the equivalent stress peak value of the central monitoring unit of the cover plate first increased and then decreased with increasing cover plate thickness. Additionally, the maximum principal stress peak value first decreased and then increased, while the maximum shear stress peak value first increased and then decreased. During the loading positive pressure stage, the maximum principal strain peak value of the monitoring unit decreased overall with increasing cover plate thickness. However, the equivalent plastic strain peak value initially increased and then decreased gradually. The equivalent strain indicated that plastic damage occurred in the cover plate. Beyond a thickness of 0.11 m, increasing the cover thickness did not appear to enhance its resistance to plastic damage. The damage analysis revealed that as cover plate thickness increased, the peak displacement and velocity of the monitoring unit continued to decrease, while the overall stability and explosive resistance of the cover plate increased. Additionally, the number of damaged fragments decreased. However, once the cover plate thickness reached 0.11 m, the bonding performance of the reinforced concrete structure had been fully developed, increasing the thickness of the cover plate no longer had a significant impact on the explosive resistance of the cover plate.