多因素影响下巷道变形特性数值模拟研究

基于FLAC3D有限差分软件对开挖深度、侧压力系数、断面形状等多因素影响下的巷道变形参数进行正交试验，根据正交试验分析结果，分别选取同一深度条件下的圆形、马蹄形、直墙拱形、矩形巷道进行模拟试验并以圆形巷道作为典型断面，对不同深度下的巷道变形特征进行模拟试验。研究结果表明:开挖深度对巷道开挖后的应力差变化影响明显，断面形状对巷道围岩内的塑性区深度和具有显著影响；巷道开挖后的塑性区深度和随形状指数增加而呈线性增长趋势，圆形巷道的塑性区深度和最小，矩形最大；应力差随着巷道开挖深度的增加呈线性增加，深部开采应重视巷道内的应力分布情况。     

Storage and sequestration of organic carbon in major paddy soils of China： Mechanism, stability and the impact on global change——A key project funded by the National Natural Science Foundation of China（2003-2005）

Chinapaddysoilsoccupyalandareaofabout3×107hm2andproduce44%oftotalcerealsofthestatewithalandportionof25%.Managementofpaddysoilscanbetracedbackto7000yearsB.P.andhaveledtoaparticularsoiltypeofanthropogenicwetlandsoilswithenhancedCstorageincomparisonwiththeu…     

超塑性材料轴对称镦粗时的变形力计算

本文探讨了变分理论在超塑性成形方面的应用,建立了适合超塑性材料的变分理论的基本方程,并比超塑性材料轴对称镦粗为例验证了这些方程的正确性。     

Chemical behavior of organic compounds in the interface of water/dual-cation organobentonite

The sorption behavior of polar of ionizable organic compounds,such as p-nitrophenol,phenol and aniline,in the water/organobentonite systems is investigated.Both adsorption and partition occur to the sorption of organic compounds to dual-cation organobentonites.The separate contributions of adsorption and partition to the total sorption of organic compounds to dual-cation organobentonites are analyzed mathematically in the first time.The factors to the contributions are also discussed.The results indicated that the contribution of adsorption and partition is related to the composition and ratio of dual-cation surfactants exchanging onto the bentonite.The sorption of organic compounds to dual-cation organobentonite is dominated by adsorption at low concentrations and by partition at high concentrations,making the organobentonites powerful sorbents for organic contaminants over wide range of concentrations.     

利用塑性介质挤胀成形三通管接头变形力的研究

此文对利用塑性介质挤胀成形三通管接头变形力进行了实验研究。设计了一套挤胀成形三通管接头的通用装置,并利用此装置进行了三通挤胀成形实验。此研究给出了影响成形过程的一些重要参数。将理论结果与实验结果进行了对比,两者吻合较好。     

高应变速率反挤压超塑Zn-Al_(22)合金管材

此文简要地叙述了工业性试生产Zn-Al_(22)超塑性管材的工艺流程。采用慢速等液面浇注法和几次均匀化处理实现晶粒细化。在ε=2×10~(-2)S~(-1)的高应变速率下进行反挤压Φ49×2.25×250mm管材1200只,超塑性能最高值δ=1620％,流变应力σ_b=2.36MPa。     

关于宽板塑性弯曲变薄理论解的讨论

指出了宽板塑性弯曲原理论解[1]和实验值[2]的矛盾,提出了一种新的理论解法,并与实验值作了比较,二者非常接近。     

关于塑性应变比的测定

此文用直接法和间接法研究了δ值和计算方法对γ值的影响。发现γ值基本上与δ无关。δ只影响其测量精度,δ愈大愈有利于提高γ的测量精度。计算方法对γ值的影响只在δ值较小时。随δ增大,计算方法的影响逐步消除。