高寒条件下振弦式传感器在线测量尾矿坝浸润线的误差分析及对策

为减少和消除高寒条件下振弦式传感器在线测量浸润线的误差,通过理论分析和现场试验,对造成误差的因素及其影响情况进行了深入研究。结果表明,振弦式传感器产生测量误差的主要来源为设备安装深度的测量误差与尾矿水密度及重力加速度的取值误差,并提出了减少或消除误差的方法和工程技术措施,为高寒地区的浸润线在线精确测量提供了重要指导意义。     

对生态红线的研究——宁夏生态红线划定的问题和思考

为了贯彻国家的可持续发展战略,更有效地解决中国的环境危机以及更好地进行中国的生态文明建设,就必须建立底线思维.中央第十八届三中全会通过的《中共中央关于全面深化改革若干重大问题的决定》明确规定了要划定生态保护红线.通过对生态保护红线的相关文献和政策进行分析,提出生态红线的类型和划定的思考,结合生态红线落地问题,对宁夏生态红线划定中存在的问题进行思考,以期为全国生态红线划定和生态保护提供参考.     

公路线源大气环境影响预测方法对比分析研究

文章通过从模式原理、范围和特点等方面对AERMOD大气预测模式与EIAA预测模式进行对比分析,以甘肃省天水段G310国道升级改造项目为例,分别采用AERMOD和EIAA两种模式对交通线源排放的特征污染因子CO在各环境空气敏感点的小时最大浓度进行预测,并对预测值与实测值进行对比分析,探讨两种模式在公路线源大气环境影响预测中的适用性及差异性。以期为今后开展道路交通类建设项目大气环境影响预测评价中模式的选取提供参考和借鉴。     

探索性数据分析在西藏气候变化趋势研究中的应用

为了减少小样本时间序列资料中个别异常值对气候变化趋势分析的破坏性影响,采用探索性数据分析方法之一的三组耐抗线对西藏近30年气温、云量资料进行线性趋势分析,研究了西藏地区气温和云量的变化趋势及其区域分布,并讨论了二者的相关特征。通过与传统的最小二乘法相比,表明三组耐抗线用于西藏气候变化趋势分析具有明显优势,而用最小二乘法得到的西藏气候变暖估计偏高。分析认为,西藏气候变暖主要由最低气温增高显著所致,最低气温变暖趋势在春、夏季较明显,冬季相对不明显;西藏各地增温幅度在空间分布上不一致,中、西部地区呈较强的增温趋势,东部相对较弱;西藏高原总云量和低云量总体呈减少趋势,总云量和低云量变少分别与西部和中部地区的升温之间存在显著负相关关系。     

放射源在线监控系统设计与应用

为了防止在使用放射源时发生脱落、丢失、超标使用、私自转移等情况,最大限度避免辐射安全事故,有必要设计建立放射源在线监控系统,对放射源放射性指标(辐射剂量率)及所处位置(经纬度)实行连续的自动监测。并通过各级监管平台设置放射源超标、异动等报警程序,全面提升放射源科学监管水平。     

2015年冬季京津冀两次重污染天气过程气象成因

为了分析京津冀地区2015年11月27日~12月1日和12月19日~25日这2次重污染过程,从环流形势、大气稳定度条件、动力条件、水汽条件、近地层风场输送等几个方面对重污染天气的形成机制展开分析,结果表明：这2次重污染天气过程均属于静稳型,津京冀各地重度以上污染时长均超过50%.在大范围静稳形势存在时,过程一期间边界层内的垂直扩散条件较过程二偏弱,过程一期间地面辐合线位置偏北且维持不动,过程二期间辐合线位置偏南且略微南北摆动,导致了2次过程重污染区域和污染增长速率的不同.对北京而言,过程一前期降雪融化提供了有利水汽条件,弱偏南风有利于污染物和水汽的输送,混合层高度持续异常偏低（京津冀平均混合层高度339m）、过程期间伴随弱下沉运动（0~2Pa/s）、多层逆温（且厚度大）造成日变化不明显,地面辐合线在北京中部维持等多重因素,使得污染浓度极高,北京地区PM_2.5峰值浓度达593mg/m³.过程二前期采取了减排措施,能见度和PM_2.5日变化大、污染发展较过程一前期平缓;后期不利气象条件叠加污染排放,导致了PM_2.5爆发式增长,其中邢台PM_2.5峰值浓度达70mg/m³,增长率超过7.2mg/（m³·h）.     

Sustainable management of demolition waste—an integrated model for the evaluation of environmental, economic and social aspects

A model is presented for evaluating waste management systems for their contribution to a sustainable development, including environmental, economic and social aspects. The model was tested in a case-study, where groups of long-term unemployed people were offered both education on environmental issues and practical work with the recovery and recycling of building and demolition waste as a form of vocational development. Application of the suggested model revealed the overall effects on sustainability of different methods of waste management. In addition, negative aspects of the systems analysed were identified, which led to discussions about possible improved practices within the waste management systems. Two of the waste management systems investigated (the recycling of steel and re-use of sanitary porcelain) showed a potential contribution to sustainable development in all of the aspects studied. Preparing bricks for re-use showed the largest potential for eco-efficiency, but had negative effects on sustainability from the social perspective of health and the working environment. The possibility of further use of the model and the remaining obstacles to such analyses are discussed. One observation is that the data collection needed to perform this kind of sustainability analysis is resource-demanding, and that it would therefore be better to identify a smaller number of key indicators.     

Processing and Characterization of Short-Fiber Reinforced Jute/Poly Butylene Succinate Biodegradable Composites: The Effect of Weld-Line

Fabrication of complex injection molded parts often involves the use of multiple gates. In such situations, polymer melts from different gates meld to form the molded part (weld line). This paper reports on the fabrication and characterization of the mechanical and morphological properties of short fiber reinforced jute/poly butylene succinate (PBS) biodegradable composites. The effect of a dual gated mold in the fabrication of welded specimens was a key focus of the investigation. It was observed that incorporation of jute fiber (10 wt%) conferred drastic changes on the stress–strain properties of the matrix as the elongation at break (EB), dropped from 160% in the matrix to just 10% in the composite. The tensile strength of the composite was lower than that of the matrix. However, it is noteworthy that the tensile modulus of the composite increased. Bending test also revealed that both bending strength and modulus increased with the incorporation of jute. Morphological studies of the tensile fracture surface using SEM revealed two types of failure mode. Ductile failure was indicated by plastic deformation at the initiation of fracture followed by brittle failure. The good interfacial bonding indicated between jute and PBS was attributed to positive interaction between the two polar polymers. A comparison of the non-weld and weld-line samples revealed that the weld-line composites have better mechanical integrity than the corresponding polymer matrix with weld line. The results also revealed that elongation at break and toughness are most sensitive to the presence of the weld-line whereas flexural properties are least sensitive.     

恶臭假单胞菌Pseudomonas putida 5-x细胞壁膜系统的Cu2+吸附性能

对1株从电镀废水中分离出的革兰氏阴性菌恶臭假单胞菌P.putida 5-x的细胞表面组分对Cu²⁺的吸附性能进行了分析研究.结果表明,分离的P.putida 5-x细胞壁膜的Cu²⁺吸附容量是完整细胞的5倍之多.细胞表面组分如肽聚糖层、细胞外膜和细胞内膜在P.putida 5-x细胞壁膜的Cu²⁺吸附过程中都发挥了作用.肽聚糖层、细胞外膜和内膜在P.putida 5-x细胞壁膜中的含量依次为细胞内膜>外膜>肽聚糖层,而它们的Cu²⁺吸附容量的大小依次为肽聚糖层>外膜>内膜.在P.putida 5-x细胞壁膜对Cu²⁺的吸附过程中,肽聚糖层贡献了不到15%的吸附容量,而细胞外膜和内膜分别贡献了30%～35%和25%～30%.P.putida 5-x细胞外膜中的磷脂含量明显比其它报道的革兰氏阴性细菌的细胞外膜高,这可能是P.putida 5-x细胞外膜具有较高Cu²⁺吸附容量的主要原因,并由此导致P.putida 5-x细胞壁膜的高Cu2+吸附容量.     

潜流湿地处理生活污水时的强化策略

研究在潜流湿地处理生活污水时通过预处理强化、介质优化和工艺改进克服现有技术缺陷的可行性.改进方法包括化学强化预处理、预曝气、添加氮吸附介质、添加磷吸附介质、湿地高浸润线、中浸润线、低浸润线和动态浸润线运行.结果表明,化学强化预处理不仅可以除磷,而且削减湿地污染负荷可使后续湿地面积减小63%,但是不能有效脱氮.预曝气仅使氨氮去除率提高了1%.添加氮吸附介质的有效时间短,运行前3个月对NH₄⁺-N去除率为84%,5个月后下降到64%.添加磷吸附介质的有效时间较长,可维持数年.因此,脱氮过程只有通过基质微生物实现.稳态浸润线下对COD、NH₄⁺-N、TN、TP的去除率,高浸润线湿地为50%、21%、32%、-26%;中浸润线湿地为53%、48%、48%、-14%;低浸润线湿地为74%、96%、35%、22%.提出动态浸润线及序批式潜流人工湿地工艺(CBSW),其对COD、NH₄⁺-N、TN、TP去除率为67%、62%、53%、33%.CBSW实现了单级湿地内好氧/缺氧环境的交替出现,提高了脱氮能力,除污综合表现最佳.