Research on different venting performance between flat and curved bursting panels

There is a noticeable discrepancy in the ability to control reduced explosion overpressure between flat bursting panels and curved bursting panels with the same static activation overpressure. Flat bursting plates were observed to leak at approximately 80% of the static activation overpressure lower than curved bursting plates. A new experimental technique is proposed in our paper. Three different vent areas of flat and curved bursting panels were tested, there was significant difference in structural stiffness between flat bursting panels and curved bursting panels, which is the reason the discrepancy in the ability to control reduced explosion overpressure. The structural stiffness of the flat bursting panels is poorer than that of the other, and a greater deformation of the flat bursting panels occurs under the same load. The membrane stress caused by the explosion overpressure therefore produces a larger value in the flat bursting panels which causes it to open prematurely. Moreover, the smaller the vent area that is, the more significant discrepancy in controlling the reduced explosion overpressure between both bursting panels is. This experimental and theoretical result in our paper provides some useful experience for the method of explosion venting.     

Study of the influence of melamine polyphosphate and aluminum hydroxide on the flame propagation and explosion overpressure of aluminum magnesium alloy dust

When aluminum magnesium alloy dust floats in the air, a certain ignition energy can easily cause an accidental explosion. To prevent and control the occurrence of accidental explosions and reduce the severity of accidents, it is necessary to carry out research on the explosion suppression of aluminum magnesium alloy dust. This paper uses a vertical glass tube experimental device and a 20 L spherical explosive experimental device to carry out experimental studies on the suppression of the flame propagation and explosion overpressure of aluminum magnesium alloy dust with melamine polyphosphate (MPP) and Al(OH)₃. With increasing MPP and Al(OH)₃ concentrations, the flame brightness darkened, the flame velocity and propagation distance gradually decreased, and P_max and (dp/dt)_max decreased significantly. When the amount of MPP added reached 60%, the flame propagation distance decreased to 188 mm, which is a decrease of 68%, and the explosion overpressure decreased to 0.014 MPa, effectively suppressing the explosion of aluminum magnesium alloy dust. The experimental results showed that MPP was more effective than Al(OH)₃ in inhibiting the flame propagation and explosion overpressure of the aluminum magnesium alloy dust. Finally, the inhibitory mechanisms of the MPP and Al(OH)₃ were further investigated. The MPP and Al(OH)₃ endothermic decomposition produced an inert gas, diluted the oxygen concentration and trapped active radicals to terminate the combustion chain reaction.     

Numerical study on premixing characteristics and explosion process of starch in a vertical pipe under turbulent flow

Fire and explosion accidents are frequently caused by combustible dust, which has led to increased interest in this area of research. Although scholars have performed some research in this field, they often ignored interesting phenomena in their experiments. In this paper, we established a 2D numerical method to thoroughly investigate the particle motion and distribution before ignition. The optimal time for the corn starch dust cloud to ignite was determined in a semi-closed tube, and the characteristics of the flame propagation and temperature field were investigated after ignition inside and outside the tube. From the simulation, certain unexpected phenomena that occurred in the experiment were explained, and some suggestions were proposed for future experiments. The results from the simulation showed that 60–70 ms was the best time for the dust cloud to ignite. The local high-temperature flame clusters were caused by the agglomeration of high-temperature particles, and there were no flames near the wall of the tube due to particles gathering and attaching to the wall. Vortices formed around the nozzle, where the particle concentration was low and the flame spread slowly. During the explosion venting, particles flew out of the tube before the flame. The venting flame exhibited a “mushroom cloud” shape due to interactions with the vortex, and the flame maintained this shape as it was driven upward by the vortex.     

Effects of nitrogen and carbon dioxide on hydrogen explosion behaviors near suppression limit

By varying inert gas content, equivalence ratio and initial pressure, this study is aimed at investigating flame propagation behaviors and explosion pressure characteristics near suppression limit. For carbon dioxide, the weakest flame floating phenomenon is observed at Φ = 1.5 and the buoyant instability is enhanced when the equivalent ratio deviates to the rich and lean sides. For nitrogen, the buoyant instability decreases with increasing equivalent ratio. Both maximum explosion pressure and maximum pressure rise rate increase firstly and then decrease with the increase of equivalence ratio, and they decrease significantly with increasing content of carbon dioxide and nitrogen. For carbon dioxide, the critical suppression ratio of Φ = 0.6, 0.8, 1.0, 1.5 and 2.0 is 7.50, 7.18, 5.74, 3.83, and 2.87. For nitrogen, the critical suppression ratio of Φ = 0.6, 0.8, 1.0, 1.5 and 2.0 is 15.83, 11.87, 9.50, 6.33 and 4.75. Compared to nitrogen, the carbon dioxide is more effective on suppressing hydrogen explosion pressure. The adiabatic flame temperature, thermal diffusivity and mole fraction of active radicals continue to decrease with increasing content of carbon dioxide and nitrogen, which contributes to the decrease of laminar burning velocity.     

Recent application of Computational Fluid Dynamics (CFD) in process safety and loss prevention: A review

In recent years, significant progress has been made to ensure that process industries are among the safest workplaces in the world. However, with the increasing complexity of existing technologies and new problems brought about by emerging technologies, a strong need still exists to study the fundamentals of process safety and predict possible scenarios. This is attained by conducting the corresponding consequence modeling and risk assessments. As a result of the continuous advancement of Computational Fluid Dynamics (CFD) tools and exponentially increased computation capabilities along with better understandings of the underlying physics, CFD simulations have been applied widely in the areas of process safety and loss prevention to gain new insights, improve existing models, and assess new hazardous scenarios. In this review, 126 papers from 2010 to 2020 have been included in order to systematically categorize and summarize recent applications of CFD for fires, explosions, dispersions of flammable and toxic materials from accidental releases, incident investigations and reconstructions, and other areas of process safety. The advantages of CFD modeling are discussed and the future of CFD applications in this research area is outlined.     

土壤渗滤处理系统运行控制的模拟研究

通过建立地下水数学模型,回答了土壤渗滤工程运行控制中的两个难点问题:(1)工程运行水力负荷.当工程地块周边存在河流时,河流水位低时,有助于增加水力负荷,反之则降低水力负荷;实际土壤运行面积的增加和独立运行单元之间的间距增加也能够增加工程运行水力负荷.(2)地下水水质监测井的优化布设.模拟工程运行后地下水水质空间分布特征,在地下水水质最不利的位置和其他特别关注的位置布置监测井,从而能够以具有典型代表性且数目较少的监测井达到准确评估工程对地下水水质影响的目的.     

硫化物生物氧化脱硫技术研究现状

介绍了近年来国内外硫化物生物氧化为单质硫的各种脱硫技术.分析总结了硫化物生物氧化为单质硫工艺的各种影响因素,包括氧硫比、溶解氧浓度、硫化物浓度、化学氧化、微生物菌种、pH值、温度等因素.提出了生物氧化脱硫技术的发展前景.该技术将脱硫和单质硫的回收和为一体,是一种安全、低成本将含硫废液变废为宝的工艺技术.     

交通荷载作用下饱和软粘土孔压-应变分析模型

针对交通荷载的作用特点设计了循环三轴试验,进而对交通荷载作用下饱和软粘土的动力特件进行厂研究.结果表明:循环荷载作用下,饱和软粘土存在临界循环应力比,采用孔压曲线所得到的临界循环应力比要小于采用应变曲线所得到的临界循环应力比.当土样不存在初始剪应力时,随着循环次数的增加,土样的应力-应变关系曲线近似原点对称,但随着初始剪应力的增大,应力-应变关系曲线逐渐表现为一系列平行曲线,峰值孔压与循环孔压幅值均逐渐减少;同时,轴应变的发展加快,但循环应变幅值逐渐减小.当循环应力比小于临界循环应力比时,对于同一初始剪应力,不同循环应力比下的孔压比-动应变曲线近似集中在同一条曲线上.通过对试验数据进行回归分析,得到了交通荷载作用下饱和软粘土残余孔压-累积塑性应变关系模型.     

高土石坝震害与抗震措施评述

目前,我国西部地区正建或拟建一大批高土石坝,这些高坝都位于地震高烈度区,做好抗震设计非常重要。本文总结了地震荷载作用下土石坝常见的几种破坏形式,包括地震永久变形、滑坡失稳、液化、防渗体破坏、次生破坏;针对这些破坏形式,总结了地震高烈度区高土石坝的抗震措施,包括预留超高、坡脚压重、坝顶加固、抗液化措施、防渗体处理等;提出了现阶段高土石坝抗震的计算方法和抗震措施存在的缺点和不足,并对我国今后的高土石坝抗震稳定研究提出了建议。     

Anaerobic tapered fluidized bed reactor for starch wastewater treatment and modeling using multilayer perceptron neural network

Anaerobic treatability of synthetic sago wastewater was investigated in a laboratory anaerobic tapered fluidized bed reactor(ATFBR) with a mesoporous granular activated carbon(GAC)as a support material.The experimental protocol was defined to examine the effect of the maximum organic loading rate(OLR),hydraulic retention time(HRT),the efficiency of the reactor and to report on its steady- state performance.The reactor was subjected to a steady-state operation over a range of OLR up to 85.44 kg COD/(m~3.d).The COD removal efficiency was found to be 92% in the reactor while the biogas produced in the digester reached 25.38 m~3/(m~3·d) of the reactor. With the increase of OLR from 83.7 kg COD/(m~3.d),the COD removal efficiency decreased.Also an artificial neural network(ANN) model using multilayer perceptron(MLP)has been developed for a system of two input variable and five output dependent variables. For the training of the input-output data,the experimental values obtained have been used.The output parameters predicted have been found to be much closer to the corresponding experimental ones and the model was validated for 30% of the untrained data.The mean square error(MSE)was found to be only 0.0146.