粘弹性地基上钢筋混凝土方板在低速撞击下的动力响应分析

针对工程中所遇到的撞击问题,在事先仅知道初速度的情况下,研究分析了半无限线性粘弹性地基上的钢筋混凝土方板受低速刚体撞击时的动力响应问题。与高速冲击问题中板结构发生局部破坏的情况不同,低速撞击下板结构发生的是整体响应破坏,因此计算时主要考虑结构的整体响应,但仍须考虑撞击局部损伤影响。建立了局部变形和整体响应间的关系模型,根据该模型推导出钢筋混凝土方板在低速撞击下位移响应w(x,y,t)和撞击反力p(t)的表达式,并结合算例讨论了粘弹性地基对计算结果的影响。     

Recycling of an industrial sludge and marine clay as light-weight aggregates

The geographical limitations of Singapore, its restricted natural resources and voluminous municipal and industrial waste streams, make environmental management a major challenge for the island state. In an attempt to find ways to reduce importation of raw materials and the waste sent to landfill, light weight aggregates were produced from marine clay and a CaF(2)-rich semiconductor industry sludge. Aggregates were produced in a bench-scale rotary kiln with three clay/sludge loadings (90/10, 70/30 and 50/50%). All three mixtures showed good bloating behavior during firing and the ceramic pellets (1-1.5cm diameter) had densities well below that required for light-weight aggregates. In the initial tests, the pore sizes of the aggregates were in general too large resulting in high water absorption. Comparisons between the composition of the two waste products and the aggregates showed a significant loss of fluorine (40-60%) during processing; a problem which may require flue gas treatment. Leach testing showed that the formed aggregates would not pose a human or environmental hazard in terms of fluorine mobilization.     

生物质炭对Cd污染土壤团聚体酶活性的影响

为探究生物质炭对Cd污染土壤团聚体酶活性的影响,采用盆栽试验,向模拟Cd污染土壤中添加生物质炭并测定水稻根际土壤团聚体碳循环酶与氧化还原酶活性.结果表明:Cd污染土壤团聚体酶活性对添加量为2.5％的生物质炭响应明显,氧化还原酶活性指数值介于0.522～0.792之间.在2.5mg/kg的外源Cd条件下,2.5％的生物质...     

降雨过程中红壤团聚体粒径变化对溅蚀的影响

为揭示团聚体粒径动态变化对溅蚀的影响,通过室内人工模拟降雨试验,以第四纪粘土、泥质页岩发育红壤为研究对象,研究了酒精预湿润后的2~5 mm团聚体在降雨过程中粒径动态变化及溅蚀率的变化。试验结果表明：在60 mm/h雨强下,团聚体受雨滴机械打击破碎主要发生在降雨的最初阶段,团聚体＞0.25 mm百分含量（P＞0.25）及平均重量直径（M）均随降雨时间（T）增加呈幂函数减小,溅蚀率（Dr）随降雨时间（T）增加呈幂函数增加,而溅蚀率（Dr）随团聚体平均重量直径（M）减小呈幂函数增大。为揭示不同土样在降雨溅蚀过程中溅蚀率的变化规律,利用团聚体稳定性特征参数-机械破碎指数（R）及降雨时间（T）,建立了不同团聚体稳定性土样溅蚀率随降雨时间变化的经验方程,且方程可决系数较高（R2=0.82）,揭示出团聚体稳定性越好,其破碎过程越缓慢,溅蚀率越小。研究结果为红壤区土壤侵蚀的防治及侵蚀机理研究提供了新思路     

Production of lightweight aggregates from mining and industrial wastes

Washing aggregate sludge from a gravel pit, sewage sludge from a wastewater treatment plant (WWTP) and a clay-rich sediment have been physically, chemically and mineralogically characterized. They were mixed, milled and formed into pellets, pre-heated for 5 min and sintered in a rotary kiln at 1150 °C, 1175 °C, 1200 °C and 1225 °C for 10 and 15 min at each temperature. The effects of the raw material characteristics, heating temperatures and dwell times on the loss on ignition (LOI), bloating index (BI), bulk density (ρ_b), apparent and dry particle densities (ρ_a, ρ_d), voids (H), water absorption (WA_24h) and compressive strength (S) were determined. All the mixtures presented a bloating potential taking into consideration the gases released at high temperatures. The products obtained were lightweight aggregates (LWAs) in accordance with Standard UNE-EN-13055-1 (ρ_b ≤ 1.20 g/cm³ or particle density ≤ 2.00 g/cm³). LWAs manufactured with 50% washing aggregate sludge and 50% clay-rich sediment were expanded LWAs (BI > 0) and showed the lowest apparent particle density, the lowest water absorption and the highest compressive strength. It was possible to establish three groups of LWAs on the basis of their properties in comparison to Arlita G3, F3 and F5, commercially available lightweight aggregates manufactured in Spain. Our LWAs may have the same or similar applications as these commercial products, such as horticulture, prefabricated lightweight structures and building structures.     

Increasing exfiltration from pervious concrete and temperature monitoring

Pervious concrete typically has an infiltration rate far exceeding any expectation of precipitation rate. The limiting factor of a retention based pervious concrete system is often defined by how quickly the underlying soil subgrade will infiltrate the water temporarily stored within the concrete and/or aggregate base. This issue is of particular importance when placing a pervious concrete system on compacted fine textured soils. This research describes the exfiltration from twelve pervious concrete plots constructed on a compacted clay soil in eastern Tennessee, USA. Several types of treatments were applied to the clay soil prior to placement of the stone aggregate base and pervious concrete in an attempt to increase the exfiltration rate, including: 1) control – no treatment; 2) trenched – soil trenched and backfilled with stone aggregate; 3) ripped – soil ripped with a subsoiler; and 4) boreholes – placement of shallow boreholes backfilled with sand. The average exfiltration rates were 0.8 cm d⁻¹ (control), 4.6 cm d⁻¹ (borehole), 10.0 cm d⁻¹ (ripped), and 25.8 cm d⁻¹ (trenched). The trenched treatment exfiltrated fastest, followed by the ripped and then the borehole treatments, although the ripped and borehole treatments were not different from one another at the 5% level of significance. The internal temperature of the pervious concrete and aggregate base was monitored throughout the winter of 2006–2007. Although the temperature of the pervious concrete dropped below freezing 24 times, freezing concrete temperatures never coincided with free water being present in the large pervious concrete pores. The coldest recorded air temperature was −9.9 °C, and the corresponding coldest recorded pervious concrete temperature was −7.1 °C. The temperature of the pervious concrete lagged diurnal air temperature changes and was generally buffered in amplitude, particularly when free water was present since the addition of water increases the thermal capacity of the pervious concrete greatly. The temperature of the aggregate base was further buffered to diurnal changes, and no freezing temperatures were recorded.     

Experimental study of recycling lightweight concrete with aggregates containing expanded glass

The focus is on the issue of waste management when constructing and recycling lightweight concrete (LWC) with aggregates containing expanded glass. The paper analyses the recycling of concrete from lightweight aggregates, and on the important issue of environmental and waste management. The characteristics of recycling LWC such as density, compressive strength and thermal conductivity are investigated, and compared with normal existing concrete from lightweight aggregates. The results indicate that it is possible to recycle lightweight concrete construction waste. The described method shows great possibilities for increasing the use of construction waste materials from LWC containing expanded glass, in order to benefit from better use of the available capacity from existing construction waste. The characteristics of density, compressive strength and thermal conductivity from the new recycled material were compared with normal existing concrete from lightweight aggregates, such as changes in dependency on the type and parts of waste as well as its new binding components. Thus, a new recycled material has been created with new characteristics of density, compressive strength and thermal conductivity, which is conform to the compressive strength class and rules on heat protection and energy efficiency use in buildings (SI OJ RS No. 42/2002). Laboratory density, compressive strength, and thermal conductivity tests results showed that LWC can be produced by the use of waste LWC with aggregates containing expanded glass. However, the use of waste LWC with aggregates containing expanded glass seems to be necessary for the production of cheaper and environmentally friendly LWC.     

考虑人因差错影响的结构可靠度计算方法

通过对单个或任意多个人因差错影响下构件截面失效概率计算方法的分析讨论,推导出在理想已知条件下的数学解析求解公式;在考虑人因差错对结构参数影响程度的空间离散化后,得出了相应的简化计算方法;并以一个单筋梁的正截面为例进行了失效概率计算和人因差错影响程度分析.在目前人因差错的发生及其影响规律的研究不完善、缺乏必要的数学模型的现实条件下,该方法对人因差错影响下构件截面失效概率的分析计算有一定的实用价值.     

爆炸荷载作用下钢筋混凝土防爆墙动力响应研究

为了研究钢筋混凝土防爆墙的抗爆能力,采用有限元分析方法对不同纵向配筋率、不同高跨比、不同厚度的墙体在爆炸动态荷载作用下的动力响应进行研究,对各种不同设置的钢筋混凝土防爆墙的抗爆性能进行评估。结果表明:减小高跨比对提高钢筋混凝土防爆墙的抗爆能力最为重要,提高纵向配筋率,增加厚度都能增加防爆墙的抗爆能力。     

基于灰预测模型的大跨度预应力混凝土桥梁施工监测

运用灰色系统理论,建立大跨度预应力砼刚构-连续组合梁桥悬臂浇筑施工梁段立模标高预测的GM(1,1)模型,并用残差的GM(1,1)模型对其进行修正;同时把该预测模型应用于松原龙华松花江特大桥实际工程;其结果表明梁段立模标高预测精度较高,完全能够满足工程的需要,为同类桥梁的施工监测提供参考。