一种高柔结构的减震装置

介绍了国内外高柔结构减震装置的研究现状，提出了一种新的高柔结构减震装置，并对该装置进行了原理分析和计算。为了检验该高柔结构减震装置的减震效果，在大型结构振动台上进行了模型试验，实验结果表明，由于减震装置的约束作用，增加了系统的刚度，系统共振频率略有增大，该减震装置具有明显的减震效果。最后，对该减震装置在灾害救生方面上的应用前景进行了展望。     

常规兵器三综合环境试验技术研究

对温度-湿度-振动综合试验过程中的环境应力故障分析、试验标准剪裁、试验量值确定、试验设备及试验过程、试验结果评定等问题进行分析论述，分析结果对温度-湿度-振动综合试验设备选型和温度-湿度-振动综合试验具有参考价值。     

Intrinsic and Stimulated In Situ Biodegradation of Hexachlorocyclohexane (HCH)

The feasibility of the biodegradation of HCH and its intermediates has been investigated. A recent characterisation of two sites in The Netherlands has shown intrinsic biodegradation of HCH. At one site, breakdown products (monochlorobenzene, benzene and chlorophenol) were found in the core of the HCH-plume, whereas the HCH-concentration decreased over time and space. Characterisation of a second, industrial site indicated less intrinsic biodegradation and the need to stimulate biodegradation. In the laboratory, enhanced HCH degradation was tested with soil and groundwater material from both sites, and the required conversion to the intermediates benzene and monochlorobenzene was demonstrated. Furthermore, the biodegradation of these intermediates could be initiated by adding low amounts of oxygen (<5%). Adding nitrate enhanced this degradation. We hypothesise that this occurs through anaerobic nitrate reducing conversion of oxidised intermediates.At the non-industrial other site, intrinsic degradation took place, as shown in the laboratory experiments. Interpretation of the field data with computer codes Modflow and RT3D was performed. As a result of the modelling study, it has been proposed to monitor natural attenuation for several years before designing the final approach.At the industrial site, the results of the batch experiments are applied. Anaerobic HCH degradation to monochlorobenzene and benzene is stimulated via the addition of an electron donor.Infiltration facilities have been installed at the site to create an anaerobic infiltration zone in which HCH will be degraded, and these facilities are combined with the redevelopment of the site.     

沂沭断裂带上跨断层定点水准高值变化分析

2001年8月,沂沐断裂带上的冯家坊子和相公庄定点水准测量在更换了DiNill数字水准仪后同时出现高值变化。本文计算了冯家坊子、相公庄水准2000～2002年1～7月高差中数的偶然中误差,利用t检验、f检验对不同年相同时间段的均值、方差进行了统计检验,并结合地下水位、降雨、温度、环境等因素从定量和定性两个方面分析了水准观测值与它们之间的关系;讨论了引起水准观测值出现显著变化的原因。结果表明:冯家坊子、相公庄水准出现的高值变化与更换了数字水准仪有关,而冯家坊子水准出现的高值变化还与温度、地下水位变化有关,相公庄水准SN向出现的高值变化还与周围环境干扰有关。     

电动振动台台面加速度失真度的分析

通过对影响电动振动台失真度因素的定性分析，得出影响失真度的理论依据，提出降低电动振动台台面加速度失真度的措施，供设计电动振动台及使用电动振动台者参考。     

DEVELOPMENT OF A FRACTURED MEDIUM FLOW MODEL FOR A WASTE SITE1

ABSTRACT: A three‐dimensional fractured medium flow model was developed for the Bear Creek Valley (BCV) S‐3 site of the Oak Ridge Reservation (ORR) using SWIFT III. The numerical modeling for this site focused on a conceptual model established through the analysis of heterogeneous geologic units and matrix fracture properties of the subsurface in the BCV area. The SWIFT III modeling analysis was based on the previous modeling studies that used MODFLOW and MODPATH. A rigorous calibration was obtained first by comparing simulated results with the existing data on ground water levels and then by comparing pumping test results with the simulated ground water levels. A satisfactory agreement between observed and simulated results was obtained. The calibrated model was used to determine sustained yield from a ground water interceptor trench. Different withdrawal rates were used to simulate the performance of the trench for the sustained withdrawal of ground water.     

氢化物发生-原子荧光法测定一次性餐具中砷

建立了一次性餐具中砷的氢化物发生－原子荧光测定方法，在选定的试验条件下，荧光强度与砷质量浓度在0μg/L－180μg/L范围内呈线性关系，相关系数0．999 3，溶液检测限0．5μg/L，回收率96％－101％。     

汽车环境风洞地面区域流场数值仿真

目的 探究汽车环境风洞地面区域流场规律,获取风洞边界层抽吸装置的最佳抽吸率和底盘测功机对风洞地面区域边界层厚度、风速、总压和静压的影响规律,并比较MRF法和旋转壁面法对底盘测功机转毂转动模拟的精度。方法 运用计算流体动力学方法对汽车环境风洞流场进行数值仿真计算。结果 边界层抽吸装置对应于喷口风速120 km/h时的最佳抽吸率为0.048。底盘测功机区域总压呈现下降趋势。相比于存在底盘测功机,汽车环境风洞无底盘测功机时,底盘测功机区域内相同位置的边界层厚度会增加1.28～12.22 mm。在前转毂的前侧、上侧、后侧和后转毂的上侧和后侧会有一个高风速区域,区域内风速比设定风速高1%～4%,与无底盘测功机相比,区域内静压值低0.32～46.02 Pa。在前后转毂前侧和后侧与地面相连接的凹部会有一个低风速区域,区域内风速比设定风速低1%～5%,与无底盘测功机相比,区域内静压值高0.08～49.34 Pa。底盘测功机转毂的转动会使附近区域的地面边界层厚度变大。在前转毂前侧,采用旋转壁面法进行模拟比MRF法地面边界层厚度增加近8 mm,而在其他位置,2种模拟方法对边界层厚度的模拟差别在1.5 mm...     

雷达吸波复合材料外观失效机理分析及控制方法研究

目的 解决多层泡沫夹芯结构的雷达吸波复合材料在环境效应下产生外观失效的问题。方法 制备3种类型的雷达吸波复合材料,开展典型自然环境试验。观察试验样品外观状态,并检测变形量。通过观察泡沫的微观组织形貌,检测热膨胀量变化及泡沫与树脂间的粘黏强度,用气相色谱质谱联用仪GCMS检测复合材料裂解气体成分,分析复合材料外观失效成因,并提出解决技术途径。结果 6个月自然环境试验后,1#、2#样品外观失效,而3#样品无明显变化。复合材料100℃裂解气体成分为氮气、二氯一氟乙烷、甲基膦酸二甲脂。4种泡沫在22～85℃的最大热膨胀量分别为–0.18%、–0.37%、–0.30%、–0.45%。环氧树脂与4种泡沫的粘黏强度在41～52N,而聚氨酯树脂达到了54～81N。结论 雷达吸波复合材料泡孔内残留气体的释放,是导致外观失效的根本原因。通过热处理工艺,减少样品残留气体量,并提升胶黏剂与泡沫的粘黏复合强度,是提升复合材料环境适应性的有效技术途径。     

直升机尾部结构疲劳及缺陷容限试验装置研制及应用

目的 获得尾部结构的疲劳寿命和检查周期,满足民用直升机适航验证要求,保证飞机的飞行安全,开展复合材料尾部结构疲劳及缺陷容限试验技术研究。方法 介绍了尾部结构疲劳及缺陷容限试验专用试验台、气动冲击设备、柔性自动特征扫描成像无损检测系统等的设计及研制,采用研制的成套试验装置,实现尾部结构试验件连接约束和载荷边界的全面真实模拟、复杂载荷谱的精确控制、冲击损伤缺陷预制及缺陷自动识别与检测。结果 经试验验证,载荷误差小于2%,冲击能量误差小于2%,缺陷检测误差小于1 mm,各项指标都满足项目研究目标和技术指标要求。结论 研究成果在民用直升机研制中得到了成功应用,可为后续其他直升机尾部结构疲劳及缺陷容限疲劳试验提供良好的借鉴,具有重要的工程应用价值。