Evaluation and Optimization of Handle Design Parameters of a Grass Trimming Machine

The grass trimming machine is a widely used agricultural machine for cutting grass by the roadside and in other areas in Malaysia. Hand-arm vibration (HAV) syndrome is very common among workers operating power tools and performing similar work for extended periods. Grass trimming involves the use of a motorized cutter spinning at high speed, resulting in high levels of HAV among its operators. The existing D-shape handle causes HAV-related stress and operational load in operators. This research proposes a new design of a handle of the grass trimming machine. When this new design was compared with the old one, it was found that the new handle resulted in 18% lower HAV. To find the lowest HAV, 3 critical parameters of the new handle (length, angle and material of the cap of the handle) were optimized using the Taguchi quality tool. Appropriately selected parameters of the new handle significantly reduced the occurrence of HAV among grass trimmers.     

A Study on the Combined Effect of Noise and Vibration on Operators’ Performance of a Readability Task in a Mobile Driving Environment

This paper presents a study in which the main objective was to investigate the combined effect of noise and vibration on the performance of a readability task in a mobile driving environment. Subjects performed a readability task on a laptop computer in a sitting posture with their backs supported with a backrest under varying levels of noise and vibration. The data in terms of the mean number of characters read per minute were collected and statistically analyzed. Results showed that the individual effect of noise, vibration, and the operators’ gender as well as the interaction between gender and noise, and gender and vibration were statistically significant. However, the combined effect of noise and vibration was not found to be statistically significant. Results also indicated that gender was statistically significant at all levels of noise as well as vibration, and noise and vibration were statistically significant at both levels of gender.     

江苏省畜禽养殖污染减排措施与政策研究

为提高江苏省畜禽养殖污染治理水平,达到污染减排要求,完成污染减排任务,本文从分析江苏省畜禽养殖业污染产生量、排放量和污染特征入手,对污染治理措施和法律、法规及政策支撑等进行了归纳总结,深入分析了目前治理中存在的主要问题,提出了适合江苏畜禽养殖污染治理的技术模式,以及促进污染减排目标实现的管理机制和保障条件。     

天然气增压站噪声和振动治理效果分析

分析了天然气增压站噪声的主要来源,在阐述降噪原理的基础上,根据增压站所在地区实际情况,采用更换消声器、修建减振沟、修建降噪厂房、优化降噪厂房墙体等不同措施,结合治理前后噪声监测数据分析,对不同措施降噪减振的效果进行评价,同时综合了采取不同措施的合理性,为类似增压站噪声和振动治理提供借鉴。     

隧道掘进爆破载荷作用下埋地管道的振动峰值速度预测研究*

为研究隧道掘进爆破过程中地震效应对邻近埋地管道安全性的影响,建立平行于隧道的埋地管道数值模型,将管道视为薄壳圆柱体,定义管道在动载荷作用下的塑性破坏准则,并利用无量纲分析法构建管道表面质点的振动速度关于振动频率与爆破持续时间的数学模型,从而研究埋地管道受震特性。结果表明:隧道掘进爆破作业下成洞侧的管道应力峰值低于非成洞侧的管道应力峰值,爆炸载荷下邻近埋地管道表面最大振动速度位于爆源与管道表面最近点处,在该点两侧45度范围内为管道易受损位置。将预测公式计算所得振速峰值与数值模型提取的振速峰值进行比较,得出二者的平均误差约为17.7 %。     

在噪声治理中二次隔振的应用实例

在噪声治理工程中应用二次隔振降低固体传声,可以起到较理想的隔振效果。二次隔振系统固有频率低,可以隔绝低频振动。对制冷系统的压缩机组进行二次隔振,取得了满意的隔振效果。     

某型飞机进气道在噪声环境中的振动疲劳分析

某型飞机进气道常出现蒙皮裂纹、铆钉松动及掉铆钉头等故障,给飞行安全带来隐患.研究发现,此类故障是进气道在强噪声环境下,噪声脉动压力引起的结构振动疲劳损伤.应用阻尼层可降低强噪声对进气道蒙皮和铆钉的破坏.发动机地面试验结果表明,进气道阻尼层的应用显著降低了蒙皮壁板的振动量级.     

振动离心复合试验系统发展概述

以电动振动台和压电激振器与离心机复合发展为主线,系统总结了以离心机为主体的振动离心复合环境试验系统发展历程以及国内外发展现状,重点介绍了电动振动台与离心机复合的关键技术及难点。最后介绍了振动离心复合环境试验系统发展趋势及展望。     

水泵系统噪声与振动控制

从水泵系统振动噪声传播途径控制的角度,着重分析了水泵机座二次隔振系统、水泵接管隔振、隔振系统位移限制、管道支架减振、管道穿墙隔振、管道阻尼隔声包扎等水泵系统振动固体传递途径的控制,消除与建筑结构之间的刚性连接。分析了振动噪声空气传播的阻隔与吸收。     

空空导弹振动试验条件分析

振动环境是空空导弹所经历的最严酷的环境之一,振动试验量级将直接影响空空导弹的结构完整性和工作性能。通过对空空导弹寿命期内经历的振动环境进行分析,针对运输、挂机飞行以及自由飞行状态下振动产生的主要诱因,结合相关标准及国外相关测试数据,初步提出了针对空空导弹的试验条件与试验方法,为相关设计人员提供了参考。