The removal of lignin and phenol from paper mill effluents by electrocoagulation

This study aims to investigate the treatment of paper mill effluents using electrocoagulation. Removal of lignin, phenol, chemical oxygen demand (COD) and biological oxygen demand (BOD) from paper mill effluents was investigated at various current intensities by using different electrodes (Al and Fe) and at various electrolysis times (1.0, 2.5, 5.0 and 7.5min). It was observed that the experiments carried out at 12V, an electrolysis time of 2min and a current intensity of 77.13mA were sufficient for the removal of these pollutants with each electrode. The removal capacities of the process using an Al electrode were 80% of lignin, 98% of phenol, 70% of BOD, and 75% of COD after 7.5min. Using an Fe electrode the removal capacities were 92%, 93%, 80% and 55%, respectively. In addition, it was found that removal of lignin, phenol, BOD and COD increased with increasing current intensity. In the experiments carried out at different current intensities, higher removal can be explained through a decrease in intra-resistance of solution and consequently an increase at the transfer speed of organic species to electrodes. It was also found that Al electrode performs higher efficiency than Fe electrode except for COD removal. However, the time required for removal of BOD was more than that of COD. The results suggest that electrocoagulation could be considered as an effective alternative to paper mill effluents treatment.     

Grazing rates of organic matter and living fungal biomass of decaying Spartina alterniflora by three species of salt-marsh invertebrates

 The pathway for the flow of salt-marsh grass production into marsh food-webs is still not well defined. We compared the abilities of three marsh macroinvertebrates [salt marsh periwinkles, Littoraria irrorata (Say) (=Littorina irrorata), salt-marsh coffee-bean snails, Melampus bidentatus (Say); and a talitrid amphipod, Uhlorchestia spartinophila Bounsfield and Heard] to access standing-dead leaves of smooth cordgrass (Spartina alterniflora Loisel). The invertebrates were incubated with naturally-decaying leaves, and the rates of removal of organic matter and living fungal biomass (ergosterol) were measured. The impact of invertebrate activity upon fungal growth rates was measured as rates of fungal-membrane synthesis (incorporation of radioacetate into ergosterol). The removal rates of organic leaf biomass per mg individual biomass were highest for amphipods (700 μg mg⁻¹ d⁻¹) and lowest for periwinkles (90 μg mg⁻¹ d⁻¹), but the relatively large biomass of the snails made their removal rates per individual greater than those of amphipods. Net removal of ergosterol by all three invertebrates was >50% for yellow-brown (early-decay) leaf blades. For fully-brown (advanced-decay) blades, >50% removal of ergosterol was found only for periwinkles; exposure to coffee-bean snails and amphipods resulted in a net ergosterol reduction of ≤20%. The lower net reduction of living fungal biomass by coffee-bean snails and amphipods may have been due to fungal-growth stimulation (2.3-fold stimulation in coffee-bean snails and 1.5-fold stimulation in amphipods). Grazing by periwinkles did not stimulate fungal growth, possibly because of its high intensity. Grazing by these three salt-marsh shredders may affect marsh-grass shoot-decay in different ways. Periwinkles may abbreviate the period of fungal production, and incorporate the decaying material relatively quickly into snail biomass and fecal-pellet rain to the sediments. Coffee-bean snails and amphipods may enhance and prolong fungal production, along with the formation of fecal-pellet rain. All three invertebrates fed preferentially on leaf blades rather than leaf sheaths, and feeding rates of gastropods were higher during the night than during the day. Received: 25 November 1998 / Accepted: 4 November 1999     

Waterborne agrichemicals compromise the anti-predatory behavior of zebrafish

Environmental Science and Pollution Research - Due to human activities, there is an increasing presence of agrochemicals residues in water bodies, which could be attributed to an increased use of...     

Bioaerosol sampling by a personal rotating cup sampler CIP 10-M

High concentrations of bioaerosols containing bacterial, fungal and biotoxinic matter are encountered in many workplaces, e.g. solid waste treatment plants, waste water treatment plants and sewage networks. A personal bioaerosol sampler, the CIP 10-M (M-microbiologic), has been developed to measure worker exposure to airborne biological agents. This sampler is battery operated; it is light and easy to wear and offers full work shift autonomy. It can sample much higher concentrations than biological impactors and limits the mechanical stress on the microorganisms. Biological particles are collected in 2 ml of liquid medium inside a rotating cup fitted with radial vanes to maintain an air flow rate of 10 l min(-1) at a rotational speed of approximately 7,000 rpm. The rotating cup is made of sterilisable material. The sampled particles follow a helicoidal trajectory as they are pushed to the surface of the liquid by centrifugal force, which creates a thin vertical liquid layer. Sterile water or another collecting liquid can be used. Three particle size selectors allow health-related aerosol fractions to be sampled according to international conventions. The sampled microbiological particles can be easily recovered for counting, incubation or further biochemical analysis, e.g., for airborne endotoxins. Its physical sampling efficiency was laboratory tested and field trials were carried out in industrial waste management conditions. The results indicate satisfactory collection efficiency, whilst experimental application has demonstrated the usefulness of the CIP 10-M personal sampler for individual bioaerosol exposure monitoring.     

Aerosol formation yields from the reaction of catechol with ozone

The formation of secondary organic aerosol from the gas-phase reaction of catechol (1,2-dihydroxybenzene) with ozone has been studied in two smog chambers. Aerosol production was monitored using a scanning mobility particle sizer and loss of the precursor was determined by gas chromatography and infrared spectroscopy, whilst ozone concentrations were measured using a UV photometric analyzer. The overall organic aerosol yield (Y) was determined as the ratio of the suspended aerosol mass corrected for wall losses (M_o) to the total reacted catechol concentrations, assuming a particle density of 1.4 g cm^?3. Analysis of the data clearly shows that Y is a strong function of M_o and that secondary organic aerosol formation can be expressed by a one-product gas–particle partitioning absorption model. The aerosol formation is affected by the initial catechol concentration, which leads to aerosol yields ranging from 17% to 86%. The results of this work are compared to similar studies reported in the literature.     

Groundwater contamination mechanism in a geothermal field: a case study of Balcova, Turkey

The Balcova Geothermal Field (BGF) located in Izmir, Turkey is situated on an east-west directed graben plain within which the hot waters surface from a fault zone that cuts the Mesozoic aged Bornova Flysch. Due to the low permeability and porosity of the Bornova Flysch, the geothermal water cycles along the immediate vicinity of the Agamemnon fault and mixes with cold waters at different depths of this fractured zone. Within the scope of this study, the mixing patterns and the groundwater contamination mechanisms are analyzed by, hydrogeological and hydrogeochemical methods. Based on the results of this research, it has been found out that the hot geothermal water and the cold regional groundwater resources of the surficial aquifer mix within the fractured zone in Bornova Flysch and within the Quaternary alluvium aquifer due to natural and anthropogenic activities including (i) the natural upward movement of geothermal fluid along the fault line, (ii) the accelerated upward seepage of geothermal fluid from faulty constructed boreholes drilled in the area, (iii) the faulty reinjection applications; and, (iv) the uncontrolled discharge of waste geothermal fluid to the natural drainage network. As a result of these activities, the cold groundwater reserves of the alluvial aquifer are contaminated thermally and chemically in such a way that various toxic chemicals including arsenic, antimony and boron are introduced to the heavily used surficial aquifer waters hindering their use for human consumption and agricultural irrigation. Furthermore, the excessive pumping from the surficial aquifer as well as the reduced surface water inflow into BGF due to the dam constructed on Ilica Creek intensify the detrimental effects of this contamination. Based on the results of this study, it can be concluded that the groundwater pollution in BGF will expand and reach to the levels of no return unless a series of preventive measures is taken immediately.     

Feasibility of incorporating waste grass clippings (Lolium perenne L.) in particleboard composites

This study investigated some of the important physical (thickness swelling) and mechanical (modulus of rupture, modulus of elasticity and internal bond) properties of single-layer particleboard panels made from eucalyptus (Eucalyptus camaldulensis Dehn.), waste of grass clippings (Lolium perenne L.) and combinations of the two. The chemical properties (pH, holocelluse and alpha cellulose contents, and water, alcohol-benzene and 1% sodium hydroxide solubilities) of the raw materials were also determined. Panels with a 6:94 ratio of grass-to-eucalyptus particles had the required mechanical properties for interior fitments including furniture and general uses. Boards manufactured with 100% grass clippings exhibited the lowest quality. The overall panel properties improved with a lower percentage of grass clippings added. Based on initial results, it also appears that grass should compose no more than 13% to achieve acceptable panel properties for interior fitments and general uses.     

Cross-border response of mosses to heavy metal atmospheric deposition in Southeastern Bulgaria and European Turkey

First cross-border atmospheric pollution of 11 heavy metals and toxic elements assessed by Hypnum cupressiforme was reported for a part of Southeastern Europe (Southeastern Bulgaria and European Turkey). Moss monitoring technique followed the main requirements of European Moss Survey. Moss samples were collected in April 2006 both in Bulgaria and Turkey. Concentration of Al, As, Cd, Cr, Cu, Fe, Ni, Pb, Sb, V, and Zn were determined by ICP-AES. Interlaboratory parallel calibration (exchanged four moss samples from each country), standard reference moss materials (M2 and M3) results ensured the study. ANOVA showed no differences between measured results in both laboratories at the 99% confidence level. Principle Component Analyze proved two factors: F1 group of Al, As, Cd, Cr, Fe, Ni, and V and F2 of Cu, Pb, and Zn as main atmospheric pollutants. Results obtained showed approximately Cu and Pb high concentrations around Istanbul and Burgas and Zn pollution in Istanbul district. Arsenic cross-border atmospheric pollution in the study area of Southeastern Europe was found.     

Evaluation of a fast wastewater odour characterisation procedure using a chemical sensor array

Sewage treatment works are one of the major sources that cause atmospheric odour pollution. The increase in the number of complaints about odour nuisance is due to the increase in environmental concerns. Unfortunately, the legislation on odour nuisance from sewage treatment works is very limited. In order to determine suitable thresholds on which to base legal standards, reliable and efficient odour measurement methods need to be defined. A chemical sensor array was developed for the purpose of measuring wastewater odour. This paper describes the development of the chemical sensor system which is specifically tuned to odours of wastewater origin and which can give an electronic measure of the wastewater odours. Odour emissions from a wastewater treatment facility were detected by using a quartz crystal microbalance (QCM) sensor array. The array consists of nine sensor elements, which were coated with different materials. In this paper, the usage of these novel instruments in the water industry was shown.