The sensitivity of surface waters of Great Britain to acidification predicted from catchment characteristics

Using a combination of soil, land use and geological information, a map of Great Britain has been derived which indicates the sensitivity of surface waters to acidification. For the geological information, a slightly modified version of an available map was used which indicated the sensitivity of groundwaters to acidification. For soils, 1-km databases of soil information for England and Wales and for Scotland were employed to map the soil sensitivity as determined by buffering capacity. The derived soils map was modified to take account of agricultural liming in arable and managed grassland areas using the ITE Land Classification. The final map of surface water sensitivity was obtained by using a geographic information system overlay procedure which enabled each combination of soil and geology sensitivity to be uniquely defined. The final sensitivity classification was based upon expert knowledge and the experience of a similar sensitivity mapping exercise for Wales.     

Major and trace elements of selected pedons in the USA

Few studies of soil geochemistry over large geographic areas exist, especially studies encompassing data from major pedogenic horizons that evaluate both native concentrations of elements and anthropogenically contaminated soils. In this study, pedons (n = 486) were analyzed for trace (Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, Zn) and major (Al, Ca, Fe, K, Mg, Na, P, Si, Ti, Zr) elements, as well as other soil properties. The objectives were to (i) determine the concentration range of selected elements in a variety of U.S. soils with and without known anthropogenic additions, (ii) illustrate the association of elemental source and content by assessing trace elemental content for several selected pedons, and (iii) evaluate relationships among and between elements and other soil properties. Trace element concentrations in the non-anthropogenic dataset (NAD) were in the order Mn > (Zn, Cr, Ni, Cu) > (Pb, Co) > (Cd, Hg), with greatest mean total concentrations for the Andisol order. Geometric means by horizon indicate that trace elements are concentrated in surface and/or B horizons over C horizons. Median values for trace elements are significantly higher in surface horizons of the anthropogenic dataset (AD) over the NAD. Total Al, Fe, cation exchange capacity (CEC), organic C, pH, and clay exhibit significant correlations (0.56, 0.74, 0.50, 0.31, 0.16, and 0.30, respectively) with total trace element concentrations of all horizons of the NAD. Manganese shows the best inter-element correlation (0.33) with these associated total concentrations. Total Fe has one of the strongest relationships, explaining 55 and 30% of the variation in total trace element concentrations for all horizons in the NAD and AD, respectively.     

19th century London dust-yards: A case study in closed-loop resource efficiency

The material recovery methods used by dust-yards in early 19th century London, England and the conditions that led to their development, success and decline are reported. The overall system developed in response to the market value of constituents of municipal waste, and particularly the high coal ash content of household ‘dust’. The emergence of lucrative markets for ‘soil’ and ‘breeze’ products encouraged dust-contractors to recover effectively 100% of the residual wastes remaining after readily saleable items and materials had been removed by the thriving informal sector. Contracting dust collection to the private sector allowed parishes to keep the streets relatively clean, without the need to develop institutional capacity, and for a period this also generated useful income. The dust-yard system is, therefore, an early example of organised, municipal-wide solid waste management, and also of public–private sector participation. The dust-yard system had been working successfully for more than 50 years before the Public Health Acts of 1848 and 1875, and was thus important in facilitating a relatively smooth transition to an institutionalised, municipally-run solid waste management system in England. The dust-yards can be seen as early precursors of modern materials recycling facilities (MRFs) and mechanical–biological treatment (MBT) plants; however, it must be emphasised that dust-yards operated without any of the environmental and occupational health considerations that are indispensable today. In addition, there are analogies between dust-yards and informal sector recycling systems currently operating in many developing countries.     

Photochemical Reactivities of Paraffinic Hydrocarbon-Nitrogen Oxide Mixtures Upon Addition of Propylene or Toluene

Effects associated with photochemical air pollution were measured during irradiation of n-butane-nitrogen oxide or n-butane-ethane-nitrogen oxide mixtures, with small amounts of propylene or toluene added. The effects measured including nitrogen dioxide and oxidant dosages, yields of formaldehyde and peroxy-acetyl nitrate, and eye irritation response. The results obtained clearly show that beneficial effects result from selective changes in hydrocarbon composition as well as from reduction of total hydrocarbon concenfration. Exclusion of olefins and alkylbenzenes was highly effective in reducing oxidant dosage, formaldehyde and peroxyacetyl nitrate concentrations, and eye irritation response. The only penalty was a modest increase in nitrogen dioxide dosage. A large reduction in nitrogen oxide concentration reduced nitrogen dioxide dosage and eye irritation response, but with the penalty of a large increase in oxidant dosage. The desirability of preferentially reducing olefins and alkylbenzenes rather than paraffinic hydrocarbons, acetylene, and benzene is strongly supported by this study. Research and development efforts should be directed toward preferential hydrocarbon control by mechanical or catalytic control     

The recycling cycle of materials as a design project tool

Currently, a large number of companies consider recycling of materials as an opportunity to maximize profits and to reduce the environmental impact generated by these materials after they are disposed. However, there is also a strong constraint on the use of recycled materials mainly due to the lack of technical/scientific information, which would relate their physical properties to their recycling cycle. This information should be used in the initial phase of the product design to serve as reference for the simulation of a project to point out the physical properties obtained from recycling the Projected material (Pm). Thus, it would be possible to foresee some recycling strategy to keep the good characteristics of recycled materials by encouraging their use, regardless of the product to be designed.Therefore, the Recycling Cycle of Materials (RCM) is a tool that provides scientific/technical support in the selection of materials. It uses the information related to the physical properties of the Pm as a parameter for product design after five recycling cycles. For the case study, this tool has been applied to obtain the basic material of ABS/PC blend. Subsequently, this blend was evaluated using DSC, FTIR, traction and impact methods to obtain delimiting data for the definition of the mechanical properties resulting from the application of RCM.     

The Removal of Particulate Matter from Fluid Bed Catalytic Cracking Unit Stack Gases

The application of a high-efficiency centrifugal type of separator to fluid bed catalytic cracking units is described in which most of the catalyst particles often lost to the atmosphere are concentrated into a small part of the stack gas (2%). A further separation can then be made on this small stream by an auxiliary separator which further concentrates the catalyst particle into 0.1% of the initia stream. Performance of the main and auxiliary separators are such as to reduce the loss of catalyst particles in the stack gas from 800 ppm to less than 60 ppm in a typical unit. Large amounts of power can be recovered by application of expander turbines to catalytic cracking plants employing this system of separation.     

Effect of Refractory on the Thermal Stability of SF6

The thermal decomposition of SF₆ is known to be oxygen-independent. Nevertheless, because of its high stability, the use of SF6 as a "conservative" surrogate in incinerator performance evaluation has been advocated and researched. This paper shows that refractory decreases markedly the stability of SF₆. The resulting increase in SF₆ decomposition was from 0 percent to 95 percent at 900°C, and the temperatures at which 90-99 percent decomposition occurred were lowered by 300-150°C. Refractory also decreased the stability of CCl₄ and C₂Cl₄, but to a lesser extent. The difference between the decompositions of C₂Cl₄ and SF₆ was reduced from several orders of magnitude to a factor of 2-4. Such a drastic and adverse change in relative stability could render SF₆ unsuitable as a "conservative" surrogate. The requirements for a "conservative" surrogate and the need for caution in its use are discussed, and further research areas are indicated.