Dry aerial fallout of organochlorine insecticide residues in Delhi, India

Monitoring of airborne dust in Delhi during May to July 1985 revealed residues of DDT varying from 1.3 to 7.14 ng mg(-1) (4.06-22.31 ng m(-2) day(-1)) with an average of 3.32 ng mg(-1) (10.38 ng m(-2) day(-1)), and HCH which ranged from 0.46 to 2.35 ng mg(-1) (1.44-7.34 ng m(-2) day(-1)) with a mean of 1.16 ng mg(-1) (3.63 ng m(-2) day(-1)). The concentration of total DDT was almost 3 times greater than that of HCH.     

Adsorptive removal of Cd2+ ions using dolochar at an industrial-scale process optimization by response surface methodology

Environmental Science and Pollution Research - In this work, performance of laboratory-synthesized dolochar has been investigated for adsorption of Cd2+ ions in a large-scale process with the...     

Assessing Respiratory Morbidity Through Pollution Status and Meteorological Conditions for Delhi

The study focuses on assessing the status of respiratory morbidity in Delhi over a four years period from 2000–2003. An attempt was made to investigate the role of important pollutants (SO₂, NO₂, SPM and RSPM) and various meteorological factors (temperature minimum & maximum, relative humidity at 0830 and 1730 hrs. and wind speed) in being responsible for respiratory admissions on account of COPD, asthma and emphysema. The study showed that winter months had greater exposure risk as pollutants often get trapped in the lower layers of atmosphere resulting in high concentrations. Statistical analysis revealed that two pollutants have significant positive correlation with the number of COPD cases viz., SPM (r = 0.474; p < 0.01) and RSPM (r = 0.353; p < 0.05), while a meteorological factor temperature (minimum) has a significant negative correlation (r = −0.318; p < 0.05) with COPD. Stepwise multiple regression analysis was performed for COPD as dependent variable and R² value of 0.33 was obtained indicating that SPM and RH(1730) were able to explain 33 percent variability in COPD. The partial correlation of SPM and RH(1730) on COPD was higher than any other combination and therefore they can be regarded as important contributing variables on COPD.     

PAHs Contamination in Bank Sediment of the Yamuna River, Delhi, India

This study was performed to elucidate the distribution, concentration trend and possible sources of PAHs in bank sediment of river Yamuna in Delhi, India. The levels of 16 priority polycyclic aromatic hydrocarbons (PAHs) were analyzed during pre-monsoon, monsoon and post-monsoon seasons in the sediment fraction < 53 μm. Reference standards and internal standards were used for identification and quantification of PAHs by HPLC. The sum of 16 PAH compounds ranged from 4.50 to 23.53 μg/g with a mean concentration of 10.15 ± 4.32 μg/g (dry wt.). Among 5 sites studied, the site, Income Tax Office (ITO) was found to be the hotspot attaining highest concentration. Predominance of 2–4 ring PAHs suggests a relatively recent local sources of PAHs in the study area. Moreover, molecular indices based source apportionment also illustrates pyrogenic source fingerprint of PAHs. No significant temporal trend was observed.     

Preliminary studies on potential remediation of acid mine drainage‐impacted soils by amendment with drinking‐water treatment residuals

Mining operations result in a wide range of environmental impacts: acid mine drainage (AMD) and acid sulfate soils being among the most common. Due to their acidic pH and high soluble metal concentrations, both AMD and acid sulfate soils can severely damage the local ecosystems. Proper post‐mining management practices are necessary to control AMD‐related environmental issues. Current AMD‐impacted soil treatment technologies are rather expensive and typically not environmentally sustainable. We conducted a 60‐day bench‐scale study to evaluate the potential of a cost‐effective and environment‐friendly technology in treating AMD‐impacted soils. The metal binding and acid‐neutralizing capacity of an industrial by‐product, drinking water treatment residuals (WTRs) were used for AMD remediation. Two types of locally generated WTRs, an aluminum‐based WTR (Al‐WTR) and a lime‐based WTR (Ca‐WTR) were used. Highly acidic AMD‐impacted soil containing very high concentrations of metals and metalloids, such as iron, nickel, and arsenic, was collected from the Tab‐Simco coal mine in Carbondale, Illinois. Soil amendment using a 1:1 Al‐ and Ca‐WTR mix, applied at 5 and 10 percent rates significantly lowered the soluble and exchangeable fractions of metals in the AMD‐impacted soil, thus lowering potential metal toxicity. Soil pH increased from an extremely acidic 2.69 to a near‐neutral 6.86 standard units over the 60‐day study period. Results from this preliminary study suggest the possibility of a successful scale‐up of this innovative, cost‐effective, and environmentally sustainable technology for remediating AMD‐impacted acid sulfate soils.     

Recycling polymeric waste from electronic and automotive sectors into value added products

The environmentally sustainable disposal and recycling of ever increasing volumes of electronic waste has become a global waste management issue. The addition of up to 25% polymeric waste PCBs (printed circuit boards) as fillers in polypropylene (PP) composites was partially successful: while the tensile modulus, flexural strength and flexural modulus of composites were enhanced, the tensile and impact strengths were found to decrease. As a lowering of impact strength can significantly limit the application of PP based composites, it is necessary to incorporate impact modifying polymers such as rubbery particles in the mix. We report on a novel investigation on the simultaneous utilization of electronic and automotive rubber waste as fillers in PP composites. These composites were prepared by using 25 wt.% polymeric PCB powder, up to 9% of ethylene propylene rubber (EPR), and PP: balance. The influence of EPR on the structural, thermal, mechanical and rheological properties of PP/PCB/ EPR composites was investigated. While the addition of EPR caused the nucleation of the β crystalline phase of PP, the onset temperature for thermal degradation was found to decrease by 8%. The tensile modulus and strength decreased by 16% and 19%, respectively; and the elongation at break increased by ~71%. The impact strength showed a maximum increase of ~18% at 7 wt.%–9 wt.% EPR content. Various rheological properties were found to be well within the range of processing limits. This novel eco-friendly approach could help utilize significant amounts of polymeric electronic and automotive waste for fabricating valuable polymer composites.

Open image in new window

     

Effect of UV radiation and temperature on mineralization and volatilization of coumaphos in water

This study was undertaken to determine the dissipation and degradation of coumaphos [O-(3-chloro-4-methyl-2-oxo-2H-1-benzopyran-7-yl) O,O-diethyl phosphorothioate] under different sunlight conditions and at different temperatures. The effect of the ultra violet (UV) component of solar radiation was also studied using quartz tubes in addition to other radiation in the visible range using glass tubes and the results were compared with those obtained under the dark light conditions. Water suspensions of coumaphos were incubated at three temperatures viz. 22°C, 37°C and 53°C in closed systems to study the effect of temperature. Volatilization, mineralization and degradation of coumaphos increased with an increase in temperature and exposure to solar radiation, particularly under the UV component of the solar radiation. Major loss of the pesticide occurred through volatilization. The optimum temperature for the degradation of coumaphos was found to be at 37°C. The data obtained from the mineralization and degradation studies indicated that 53°C crosses the biological range for suitable growth of microorganism. UV radiation exposure along with maintaining temperature at 37°C may prove useful in the dissipation and/or degradation of coumaphos prior to its disposal as waste from cattle dipping vats.     

Chromium removal from water by activated carbon developed from waste rubber tires

Because of the continuous production of large amount of waste tires, the disposal of waste tires represents a major environmental issue throughout the world. This paper reports the utilization of waste tires (hard-to-dispose waste) as a precursor in the production of activated carbons (pollution-cleaning adsorbent). In the preparation of activated carbon (AC), waste rubber tire (WRT) was thermally treated and activated. The tire-derived activated carbon was characterized by means of scanning electron microscope, energy-dispersive X-ray spectroscopy, FTIR spectrophotometer, and X-ray diffraction. In the IR spectrum, a number of bands centred at about 3409, 2350, 1710, 1650, and 1300–1000 cm^?1 prove the present of hydroxyl and carboxyl groups on the surface of AC in addition to C═C double bonds. The developed AC was tested and evaluated as potential adsorbent removal of chromium (III). Experimental parameters, such as contact time, initial concentration, adsorbent dosage and pH were optimized. A rapid uptake of chromium ions was observed and the equilibrium is achieved in 1 h. It was also found that the adsorption process is pH dependent. This work adds to the global discussion of the cost-effective utilization of waste rubber tires for waste water treatment.     

Persistence,degradation and leaching of coumaphos in soil

Abstract

Dissipation, degradation and leaching of fresh ¹⁴C coumaphos, alkylated ¹⁴C coumaphos and aged residues of ¹⁴C coumaphos from vats were studied in alkaline sandy loam soil in soil columns in the field under subtropical conditions in Delhi for a year. Dissipation, degradation and bound residue formation was more in case of alkali treated coumaphos than fresh coumaphos. After 365 days total residues of fresh coumaphos accounted for 33.25% while that of alkali treated coumaphos was 19.12%. Bound residue formation was almost double in case of alkali treated coumaphos (18.95%) than fresh coumaphos (9.53%) after 150 days followed by release of bound residue in both the cases. The proportion of metabolites 4 ‐ methylumbelliferone, chlorferon and potasan collectively was 86.05% in fresh coumaphos extractable residues while the same was 91.74% in alkali treated coumaphos after 365 days. Aged residues from vats containing copper sulphate and buffer were found to be more persistent in soil as total residues remained were 95.58% in comparison with 83.09% total residues of aged residues from vats containing only buffer after 150 days of treatment. Copper sulphate seems to inhibit the degradatiion of coumaphos in soil by microorganisms. Chlorferon was the major metabolite in generally all the samples. Coumaphos did not leach below 10 cm in all the cases.