Tourism: economic development without increasing CO2 emissions in Pakistan

Environment, Development and Sustainability - Globally, the national and cultural resources of a country are major sources of attraction for tourism. Pakistan is gifted with abundant natural and...     

焚烧飞灰重金属含量及浸出长期变化规律研究

通过对24个飞灰样品的重金属全量消解和高精度X射线荧光光谱法（HDXRF）快速检测结果进行线性回归分析,发现HDXRF法可较准确测定飞灰中Cu、Pb、Zn、Ni和Cd含量（线性回归决定系数R²³0.90）.采用HDXRF法对某焚烧厂飞灰重金属含量6个月快速检测及浸出毒性测定数据统计分析发现：飞灰重金属月均含量较稳定（变异系数CV<0.14）但日均含量波动较大（CV>2.54）;飞灰中Pb、Cu和Zn含量呈正相关（相关系数r>0.78）;金属浸出浓度受浸出液终点pH值影响显著,超标频率依次为Pb（68.9%）、Cd（66.1%）、Ni（24.0%）、Cu（14.2%）和Zn（1.6%）.短期飞灰金属含量和浸出毒性数据受焚烧工况,烟气处理工况和垃圾组分等多种因素共同影响,不具有代表性.为评估垃圾分类源头削减重金属效果,建议采用快速检测方法对焚烧飞灰重金属含量进行长期监测.     

Green innovation efficiency across China’s 30 provinces: estimate,comparison, and convergence

Mitigation and Adaptation Strategies for Global Change - Considering government and market failure of environmental regulation to combat increasing GHG (greenhouse gas) emissions, green innovation...     

专家笔谈：资源环境热点问题

重大的资源开发利用工程建设设想或实施往往容易引起社会各界的广泛关注。如何正确认识和科学评价各种资源环境热点问题是大家讨论的重点。文章认为任何重大资源开发工程必须遵循自然规律、生态规律、资源规律和经济规律,必须结合国家战略需求和地缘政治关系,开展前期深入的系统性综合调查,进行生态安全与资源工程安全评价和交叉学科论证,并对其科学价值、社会价值和经济价值等做出正确的判断。建议：未来的资源环境工程建设要谨防“大跃进”,要科学认识自然资源系统规律,守护好美丽的地球家园;要切实履行资源科学家的社会责任,提倡基于科学研究和科学态度的学术争鸣,科学问题最好还是由科学家去讨论;一些争议大的科研课题慎用公益性研发经费来支持。     

近10年中国三大经济区太阳总辐射特征及其与O3、PM2.5的关系

采用中国地面气象观测站网2007~2016年的辐射日值数据集和中国空气质量在线监测平台2014~2016年逐日观测数据,分析了京津冀、长三角和珠三角近10a太阳总辐射年际和季节变化,近3a臭氧日最大8h平均（O_{3_8h_max}）和细颗粒物（PM_2.5）的污染过程频次变化,通过不同因子及其不同强度等级的分型统计,探讨PM_2.5、O_{3_8h_max}与太阳总辐射的关系.结果表明：京津冀近10a太阳总辐射显著上升,京津冀春季和珠三角夏季太阳总辐射显著上升.三大经济区PM_2.5污染过程年频次均呈现逐年递减,且从北到南递减;O₃污染过程年频次时间上呈现先减后增,空间上京津冀多于长三角和珠三角.三大经济区O_{3_8h_max}与太阳总辐射相关系数均在0.71以上,有较强的正相关;而PM_2.5与太阳总辐射的相关性具有区域差异性.三大经济区不同季节不同太阳总辐射下O_{3_8h_max}与PM_2.5的相关关系差异显著,其中京津冀春夏秋三季O_{3_8h_max}与PM_2.5在强太阳总辐射下有较好的正相关,冬季则存在一定的负相关;长三角四季两者相关性均较弱;珠三角夏季两者正相关最为显著;不同PM_2.5浓度下O_{3_8h_max}与太阳总辐射的线性拟合效果较好,体现出较强的正相关关系,各经济区拟合曲线的倾向率均随PM_2.5升高而增大.PM_2.5>75μg/m³时拟合优度均达到最大.     

某型飞机外翼5—8肋损伤原因分析及修复探讨

目的 分析某型飞机外翼5—8肋油箱区结构不同程度损伤的原因,制定修复方案。方法采用受载分析、有限元仿真计算、静力试验数据分析等强度计算方法分析损伤产生的原因,采用扫描电子显微镜和光学显微镜对磨痕形貌进行观测等失效分析,对损伤结构件开展失效模式分析,根据损伤原因及失效模式制定科学简便的修复方案,同时对损伤长桁采取的修补措施进行强度校核。结果 通过对外翼油箱充压破坏理论分析、有限元仿真计算、静力试验数据反推,并结合飞机实际损伤情况,得出油箱破坏理论分析危险薄弱部位与真实破坏情况一致的结论。有限元仿真计算最危险结构部位与实际结构首先发生破坏部位吻合,可作为深入制定修复方案及推测实际加载压力的依据。通过静力试验数据反推、结构实际损伤及有限元仿真计算结论得出,外翼5—8肋结构出现损伤时油箱施加压力约0.5 MPa,针对损伤制定了更换外翼油箱内部第5—8肋损伤结构和贴补加强损伤长桁的修理方案,经结构强度校核,满足设计要求。结论 分析认为外翼5—8肋油箱区结构损伤原因为油箱压力超过设计值导致结构过载断裂,采用贴补加强修理损伤长桁和更换第5—8肋损伤结构的修复方案能够满足强度设计要求,可指导同类飞机类似结构损伤故障的原因分析和修理,提醒同类飞机维修人员在飞机维护时应关注外翼油箱压力超压问题。     

Suggested protocol for collecting, handling and preparing peat cores and peat samples for physical, chemical, mineralogical and isotopic analyses

For detailed reconstructions of atmospheric metal deposition using peat cores from bogs, a comprehensive protocol for working with peat cores is proposed. The first step is to locate and determine suitable sampling sites in accordance with the principal goal of the study, the period of time of interest and the precision required. Using the state of the art procedures and field equipment, peat cores are collected in such a way as to provide high quality records for paleoenvironmental study. Pertinent field observations gathered during the fieldwork are recorded in a field report. Cores are kept frozen at -18 degree C until they can be prepared in the laboratory. Frozen peat cores are precisely cut into 1 cm slices using a stainless steel band saw with stainless steel blades. The outside edges of each slice are removed using a titanium knife to avoid any possible contamination which might have occurred during the sampling and handling stage. Each slice is split, with one-half kept frozen for future studies (archived), and the other half further subdivided for physical, chemical, and mineralogical analyses. Physical parameters such as ash and water contents, the bulk density and the degree of decomposition of the peat are determined using established methods. A subsample is dried overnight at 105 degree C in a drying oven and milled in a centrifugal mill with titanium sieve. Prior to any expensive and time consuming chemical procedures and analyses, the resulting powdered samples, after manual homogenisation, are measured for more than twenty-two major and trace elements using non-destructive X-Ray fluorescence (XRF) methods. This approach provides lots of valuable geochemical data which documents the natural geochemical processes which occur in the peat profiles and their possible effect on the trace metal profiles. The development, evaluation and use of peat cores from bogs as archives of high-resolution records of atmospheric deposition of mineral dust and trace elements have led to the development of many analytical procedures which now permit the measurement of a wide range of elements in peat samples such as lead and lead isotope ratios, mercury, arsenic, antimony, silver, molybdenum, thorium, uranium, rare earth elements. Radiometric methods (the carbon bomb pulse of (14)C, (210)Pb and conventional (14)C dating) are combined to allow reliable age-depth models to be reconstructed for each peat profile.     

乌鲁木齐市餐饮业油烟污染的调查及防治初探

通过对乌鲁木齐市20家餐饮业油烟污染的调查分析，结果表明，乌鲁木齐市餐饮业油烟污染严重，并提出了防治措施。     

合成洗涤剂对小鼠诱变性研究

连续５天腹腔注射同一剂量（１／５ＬＤ５０）的合成洗涤剂，取小鼠骨髓细胞测定嗜多染色红细胞的微核率，研究表明，３种合成洗涤剂（加大香洗衣粉，洁牌餐具洗涤剂，恩威高级餐具洗洁精）使小鼠微核率有所增高，但恩威，洁牌餐具洗涤剂与对照无显著性差异。     

SI-traceable certification of Cu, Cr, Cd and Pb in sediment and fly ash candidate reference materials

Many fields in environmental analytical chemistry deal with very low limits and thresholds as set by governmental legislations or transnational regulations. The need for the accuracy, comparability and traceability of analytical measurements in environmental analytical chemistry has significantly increased and total uncertainties are even asked for by accreditation bodies of environmental laboratories. This paper addresses achieving these goals to guarantee accuracy, quality control, quality assurance or validation of a method by means of certified reference materials. The assessment of analytical results in certified reference materials must be as accurate as possible and every single step has to be fully evaluated. This paper presents the SI-traceable certification of Cu, Cr, Cd and Pb contents in geological and environmentally relevant matrices (three sediments and one fly ash sample). Certification was achieved using isotope dilution (ID) ICPMS as a primary method of measurement. In order to reduce significantly the number of analytical steps and intermediate samples a multiple spiking approach was developed. The full methodology is documented and total uncertainty budgets are calculated for all certified values. A non-element specific sample digestion process was optimised. All wet chemical digestion methods examined resulted in a more or less pronounced amount of precipitate. It is demonstrated that these precipitates originate mainly from secondary formation of fluorides (essentially CaF2) and that their formation takes place after isotopic equilibration. The contribution to the total uncertainty of the final values resulting from the formation of such precipitates was in general < 0.1% for all investigated elements. Other sources of uncertainty scrutinised included the moisture content determination, procedural blank determination, cross-contamination from the different spike materials, correction for spectral interferences, instrumental background and deadtime effects, as well as the use of either certified values or IUPAC data in the IDMS equation. The average elemental content in the sediment samples was 30-130 micrograms g-1 for Pb, 0.5-3 micrograms g-1 for Cd and 50-70 micrograms g-1 for Cu. Cr was measured in one sample and was about 60 micrograms g-1. The concentrations in the fly ash sample were up to 2 orders of magnitude higher. Expanded uncertainty for the investigated elements was about 3% (coverae factor k = 2) except for Cr, (measured by high resolution ICPMS), for which the expanded uncertainty was about 7% (k = 2).