Nitrogen evolution during the co-combustion of hydrothermally treated municipal solid waste and coal in a bubbling fluidized bed

Nitrogen evolution was studied during the co-combustion of hydrothermally treated municipal solid wastes (HT MSW) and coal in a bubbling fluidized bed (BFB). HT MSW blending ratios as 10%, 20% and 30% (wt.%) were selected and tested at 700, 800, 900 °C. Emissions of NO and N₂O from blends were measured and compared with the results of mono-combustion trials. Moreover, concentrations of precursors like NH₃ and HCN were also quantified. The results are summarized as follows: NO emissions were predominant in all the cases, which rose with increasing temperature. The blending of HT MSW contributed to the NO reduction. N₂O emissions decreased with temperature rising and the blending of HT MSW also presented positive effects. At 30% HT MSW addition, both NO and N₂O emissions showed the lowest values (391.85 ppm and 55.33 ppm, respectively at 900 °C). For the precursors, more HCN was detected than NH₃ and both played important roles on the gas side nitrogen evolution.     

海岸带含水层咸淡水界面随潮汐波动的数值模拟

在分析、研究了滨海地带含水层和不透水层的水文地质特性及含水层内的咸淡水渗流运动特征的基础上,运用数学推理的手法,建立了一种较为简单适用的模拟海岸带含水层咸淡水界面和天然地下水面变动规律的二维数学模型,通过该模型的计算值与实验值的比较,证明该模型的计算结果与实验结果有着非常好的拟合度,即该模型能较客观地揭示海水入侵引起的咸淡水界面的变化规律.其后,运用该模型系统的探讨了含水层以下为非平坦的不透水层的滨海地带天然地下水面、咸淡水界面伴随着潮汐的波动而变化的规律.即伴随着潮汐的波动,一方面天然地下水面和咸淡水界面与潮汐具有相似的振动波形,波动的幅度随离海岸距离的增加而减小.在海岸附近咸淡水界面的振幅大于天然地下水面的振幅,而在离开海岸一定距离后天然地下水面的振幅超过咸淡水界面的振幅.总体上天然地下水面的振幅呈负指数衰减,而咸淡水界面的振幅几乎呈直线衰减(其衰减直线的倾角在135～150 °之间变动),且潮汐波动对天然地下水面影响的范围远大于其对咸淡水界面的影响;另一方面天然地下水面和咸淡水界面波动的振幅及它们之间的相位差的大小还与天然地下水面的水力坡度、含水层的渗透系数、有效孔隙率、不透水层形状及其变动的幅度有关,但它们之间的相位差的大小与潮汐波动的幅度无关,其振幅与潮汐的振幅成比例增减.当不透水层的形状一定时,不论天然地下水面的水力坡度、含水层的渗透系数、有效孔隙率及潮汐波动的幅度怎么变动,天然地下水面、咸淡水界面振动的相位差的变化趋势及其峰值出现的位置几乎不变,即不透水层的形状决定着天然地下水面、咸淡水界面振动的相位差的变化趋势,而其大小与含水层的水文地质参数(水力坡度、渗透系数及有效孔隙率)密切相关.此外,当天然地下水面和咸淡水界面的振动存在相位和振幅的较大差异时,可以断定含水层以下存在非平坦的不透水层,且这种差异越大,不透水层凸凹不平的程度越高.     

Glycosylation of bisphenol A by freshwater microalgae

The endocrine disruptor bisphenol A (BPA, 4,4'-isopropylidenediphenol) is used to manufacture polycarbonate plastic and epoxy resin linings of food and beverage cans, and the residues from these products are then sometimes discharged into rivers and lakes in waste leachates. However, the fate of BPA in the environment has not yet been thoroughly elucidated. Considering the effect of BPA on aquatic organisms, it is important that we estimate the concentration of BPA and its metabolites in the aquatic environment, but there are few data on the metabolites of BPA. Here, we focused on freshwater microalgae as organisms that contribute to the biodegradation or biotransformation of BPA in aquatic environments. When we added BPA to cultures of eight species of freshwater microalgae, a reduction in the concentration of BPA in the culture medium was observed in all cultures. BPA was metabolized to BPA glycosides by Pseudokirchneriella subcapitata, Scenedesmus acutus, Scenedesmus quadricauda, and Coelastrum reticulatum, and these metabolites were then released into the culture medium. The metabolite from P. subcapitata, S. acutus, and C. reticulatum was identified by FAB-MS and (1)H-NMR as bisphenol A-mono-O-beta-d-glucopyranoside (BPAGlc), and another metabolite, from S. quadricauda, was identified as bisphenol A-mono-O-beta-d-galactopyranoside (BPAGal). These results demonstrate that freshwater microalgae that inhabit universal environments can metabolize BPA to its glycosides. Because BPA glycosides accumulate in plants and algae, and may be digested to BPA by beta-glycosidase in animal intestines, more attention should be given to levels of BPA glycosides in the environment to estimate the ecological impact of discharged BPA.     

Photodegradation of gaseous acetaldehyde and methylene blue in aqueous solution with titanium dioxide-loaded activated carbon fiber polymer materials and aquatic plant ecotoxicity tests

TiO₂-supported activated carbon felts (TiO₂–ACFTs) were prepared by dip coating of felts composed of activated carbon fibers (ACFs) with either polyester fibers (PS-A20) and/or a polyethylene pulp (PE-W15) in a TiO₂ aqueous suspension followed by calcination at 250 °C for 1 h. The as-prepared TiO₂–ACFTs with 29–35 wt.% TiO₂ were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and N₂ adsorption. The TiO₂–ACFT(PS-A20) samples with 0 and 29 wt.% TiO₂ were microporous with specific surface areas (S _BET) of 996 and 738 m²/g, respectively, whereas the TiO₂–ACFT(PE-W15) samples with 0 and 35 wt.% TiO₂ were mesoporous with S _BET of 826 and 586 m²/g, respectively. Adsorption and photocatalytic activity of the as-prepared samples were evaluated by measuring adsorption in the dark and photodegradation of gaseous acetaldehyde (AcH) and methylene blue (MB) in aqueous solution under UV light. The TiO₂ loading caused a considerable decrease in the S _BET and MB adsorption capacity along with an increase in MB photodegradation and AcH mineralization. Lemna minor was chosen as a representative aquatic plant for ecotoxicity tests measuring detoxification of water obtained from the MB photodegradation reaction with the TiO₂–ACFT samples under UV light.     

A level change in mutagenicity of Japanese tap water over the past 12 yr

A relative comparison study of mutagenicity in Japanese tap water was conducted for 1993 and 2005 surveys. It intended to assess the effects of advanced water treatment installations to water works, improvement of raw water quality and improvement of residual HOCl concentration controlling. Sampling points (taps) were the same in both surveys. The results of 245 samples obtained by the Ames Salmonella mutagenicity test (Ames test) were analyzed. The Ames tests were conducted by using Salmonella typhimurium TA98 and TA100 strains with and without exogenous activation (S9). With the exception of TA100-S9, the other conditions needed no discussion as a factor in the mutagenicity level change. The average mutagenicity in 1993 and 2005 under the conditions of TA100-S9 were 2600 and 1100 net revertant L⁻¹, respectively. This indicated that the mutagenicity level of Japanese tap water decreased during the 12-yr period. Particularly a remarkable decrease in mutagenicity was observed in the water works where the advanced water treatments were installed during the 12-yr period. The advanced water treatments were effective in decreasing the mutagenicity of tap water. Mutagenicity also decreased in the water works with conventional water treatments; the improvement of residual HOCl concentration controlling was also considered to be effective in decreasing the mutagenicity of tap water.     

The sorption of heavy metal species by sediments in soakaways receiving urban road runoff

Infiltration facilities are designed for both the retention of non-point pollutants and the replenishment of groundwater in urban areas. In this study, sorption tests were conducted to evaluate the speciation of heavy metals and their behaviour in infiltration facilities receiving urban road runoff containing high DOC concentrations and stable heavy metal organic complexes. Road dust and three soakaway sediments were collected from heavy traffic areas and a residential area with an infiltration-type sewerage system in Tokyo, Japan. Sequential multiple batch tests were conducted by adding prepared road dust leachate (artificial road runoff) or deionised water to soakaway sediment to obtain soakaway sediment leachate (artificial percolating water from soakaway sediment), which mimicked the sorption by sediments in soakaways receiving urban road runoff. Heavy metal speciation was assessed by means of a combination of anion-exchange resin measurements and MINTEQA2 model calculations, and further validated by chelating resin measurements. In road dust leachates and soakaway sediment leachates, Cu predominantly existed as organic complexes and carbonates, whereas most Mn, Zn and Cd were found to exist in the form of free ions and carbonate complexes. Stable organic complexes of Cu in road dust leachates were strongly adsorbed by soakaway sediments despite the limited adsorption of DOC. On the other hand, desorption of free Mn, Zn and Cd ions from the sediment receiving road dust leachates was observed, indicating that heavy metals such as Mn, Zn and Cd may ultimately reach groundwater as free ions.     

Investigation of 1,4-dioxane originating from incineration residues produced by incineration of municipal solid waste

As a groundwater contaminant, 1,4-dioxane is of considerable concern because of its toxicity, refractory nature to degradation, and rapid migration within an aquifer. Although landfill leachate has been reported to contain significant levels of 1,4-dioxane, the origin of 1,4-dioxane in leachate has not been clarified until now. In this study, the origins of 1,4-dioxane in landfill leachate were investigated at 38 landfill sites and three incineration plants in Japan. Extremely high levels of 1,4-dioxane 89 and 340 microg l(-1), were detected in leachate from two of the landfill sites sampled. Assessments of leachate and measurement of 1,4-dioxane in incineration residues revealed the most likely source of 1,4-dioxane in the leachate to be the fly ash produced by municipal solid waste incinerators. Effective removal of 1,4-dioxane in leachate from fly ash was achieved using heating dechlorination systems. Rapid leaching of 1,4-dioxane observed from fly ash in a sequential batch extraction indicated that the incorporation of a waste washing process could also be effective for the removal of 1,4-dioxane in fly ash.     

Laboratory longitudinal diffusion tests: 2. Parameter estimation by inverse analysis

This study focuses on the verification of test interpretations for different state analyses of diffusion experiments. Part 1 of this study identified that steady, quasi-steady and equilibrium state analyses for the through- and in-diffusion tests with solution reservoirs are generally feasible where the tracer is not highly sorptive. In Part 2 we investigate parameter identifiability in transient-state analysis of reservoir concentration variation using a numerical approach. For increased generality, the analytical models, objective functions and Jacobian matrix necessary for inverse analysis of transient-state data are reformulated using unified dimensionless parameters. In these dimensionless forms, the number of unknown parameters is reduced and a single dimensionless parameter represents the sorption property. The dimensionless objective functions are evaluated for individual test methods and parameter identifiability is discussed in relation to the sorption property. The effects of multiple minima and measurement error on parameter identifiability are also investigated. The main findings are that inverse problems for inlet and outlet reservoir concentration analyses are generally unstable and well-posed, respectively. Where the tracer is sorptive, the inverse problem for the inlet reservoir concentration analysis may have multiple minima. When insufficient measurement data is collected, multiple solutions may result and this should be taken into consideration when inversely analyzing data including that of inlet reservoir concentration. Verification of test interpretation by cross-checking different state analyses is feasible where the tracer is not highly sorptive. In an actual experiment, test interpretation validity is demonstrated through consistency between theory and practice for different state analyses.     

Trace metal speciation during dry and wet weather flows in the Tama River, Japan, by using diffusive gradients in thin films (DGT)

The labile species of Ni, Cu, Zn, Cd, and Pb in the Tama River, an urban river in Tokyo, Japan, were measured using diffusive gradients in thin films (DGT) method under dry and wet weather conditions, and the results were compared with total dissolved concentrations in hourly samples collected in parallel. A total of 10 DGT deployments were made and 251 hourly samples were collected during 2 rounds of sampling, conducted between August and October, 2006. Two types of diffusive gradients in thin films (DGT) devices-DGT-RG for labile inorganic and DGT-APA for total (inorganic and organic) labile species-were applied throughout the samplings. The proportions of metals measured by DGT, compared with the dissolved metal concentrations (filtered using a membrane of 0.5 microm pore size), were 38 +/- 5% (RG) and 45 +/- 8% (APA) for Ni and 45 +/- 22% (RG) and 53 +/- 23% (APA) for Zn. No labile Cu was detected throughout the sampling; Cu was assumed to be in stable complexed forms. Labile Pb was detected in 3 out of 10 deployments only; the rest were lower than the detection limit. Dissolved and labile Cd concentrations were below the detection limits. Three rain events encountered during the sampling periods were evaluated. Rains brought considerably higher loads of metals in dissolved form, and DGT measurements indicated that labile metal loads also increased. Selected DGT measurements were compared with the WHAM 6 speciation model and found to be similar to the model-computed results.