Chemical states of arsenic contained in sewage sludge incineration ash and insolubilized material

Journal of Material Cycles and Waste Management - The chemical states of arsenic contained in 4 kinds of sewage sludge incineration ash and insolubilized materials are analyzed using a leaching...     

Evaluation of a recycling process for printed circuit board by physical separation and heat treatment

Printed circuit boards (PCBs) from discarded personal computer (PC) and hard disk drive were crushed by explosion in water or mechanical comminution in order to disintegrate the attached parts. More parts were stripped from PCB of PC, composed of epoxy resin; than from PCB of household appliance, composed of phenol resin.In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 873–1073 K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment.As one of the mounted parts, the multi-layered ceramic capacitors (MLCCs), which contain nickel, were carbonized at 873 K. The magnetic separation is carried out at a lower magnetic field strength of 0.1 T and then at 0.8 T. In the +0.5 mm size fraction the nickel grade in magnetic product was increased from 0.16% to 6.7% and the nickel recovery is 74%.The other useful mounted parts are tantalum capacitors. The tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723–773 K in air atmosphere and screening of 0.5 mm. Silica was removed and 70% of tantalum grade was obtained after more than 823 K heating and separation.Next, the evaluation of Cu recycling in PCB is estimated. Energy consumption of new process increased and the treatment cost becomes 3 times higher comparing the conventional process, while the environmental burden of new process decreased comparing conventional process.The nickel recovery process in fine ground particles increased energy and energy cost comparing those of the conventional process. However, the environmental burden decreased than the conventional one.The process for recovering tantalum used more heat for the treatment and therefore the energy consumption increased by 50%, when comparing with conventional process. However, the market price for tantalum is very large; the profit for tantalum recovery is added. Also the environmental burden decreased by the recycling of tantalum recovery. Therefore, the tantalum recovery is very important step in the PCB recycling. If there is no tantalum, the consumed energy and treatment cost increase in the new process, though the environmental burden decreases.     

Where will large amounts of materials accumulated within the economy go? – A material flow analysis of construction minerals for Japan

For all countries analyzed so far, Material Flow Analysis/Accounting (MFA) studies indicate that the overall stock of materials within the economy is growing. Most are construction minerals such as asphalt, cement, sand and gravel, crushed stone, and other aggregates. In the analyses described in this paper, flows and stocks of construction minerals were estimated for Japan from the past to the future to elucidate: (1) the mechanisms by which construction minerals become waste, and (2) the future supply of and demand for recycled crushed stone. The following conclusions were drawn: (1) The amounts of waste construction minerals generated have been and will be at much lower levels than the domestic demand for construction minerals. These differences might indicate consistent growth of the stock of construction minerals, which will become waste in the future. However, certain amounts of materials that we account for as stock can be interpreted already in the environment as dead stock or dissipated waste; such materials can be called "missing stock" or "dissipated stock". Capturing that missing or dissipated stock is very important because it provides information that clarifies the environmental impacts and loss of resources that these materials cause; it allows estimation of appropriate future waste generation. (2) The amount of construction minerals that are recognized as waste was estimated to increase in the future. An imbalance in the supply of and demand for recycled crushed stone will likely occur in the near future if an expected decline in future road construction is considered.     

Inorganic iodine incorporation into soil organic matter: evidence from iodine K-edge X-ray absorption near-edge structure

The transformation of inorganic iodine (I⁻ and IO₃⁻) incubated in soils with varying amounts of organic matter (Andosols from the surface layer of an upland field and forest, as well as Acrisols from surface and subsurface layers of an upland field) was investigated by using the iodine K-edge X-ray absorption near-edge structure (XANES). After 60 d of reaction, both I⁻ and IO₃⁻ were transformed into organoiodine in surface soils containing sufficient amounts of organic matter, whereas IO₃⁻ remained unchanged in the subsurface soil of Acrisols with low organic matter contents. Transformation of IO₃⁻ into organoiodine was not retarded when the microbial activity in soil was reduced by γ-ray irradiation, suggesting that microbial activity was not essential for the transformation of inorganic iodine into organoiodine. Soil organic matter has the ability to transform inorganic iodine into organoiodine.     

Plutonium isotopes concentration in seawater and bottom sediment off the Pacific coast of Aomori sea area during 1991-2005

A radioactivity survey was launched in 1991 to determine the background levels of ^239+240Pu in the marine environment off a commercial spent nuclear fuel reprocessing plant before full operation of the facility. Particular attention was focused on the ²⁴⁰Pu/²³⁹Pu atom ratio in seawater and bottom sediment to identify the origins of Pu isotopes. The concentration of ^239+240Pu was almost uniform in surface water, decreasing slowly over time. Conversely, the ^239+240Pu concentration varied markedly in the bottom water and was dependent upon the sampling point, with higher concentrations of ^239+240Pu observed in the bottom water sample at sampling points having greater depth. The ²⁴⁰Pu/²³⁹Pu atom ratio in the seawater and sediment samples was higher than that of global fallout Pu, and comparable with the data in the other sea area around Japan which has likely been affected by close-in fallout Pu originating from the Pacific Proving Grounds. The ²⁴⁰Pu/²³⁹Pu atom ratio in bottom sediment samples decreased with sea depth. The land-originated Pu is not considered as the reason of the increasing ^239+240Pu concentration and also decreasing the ²⁴⁰Pu/²³⁹Pu atom ratio with sea depth, and further study is required to clarify it.     

Framework for estimating potential wastes and secondary resources accumulated within an economy – A case study of construction minerals in Japan

Material stocks in economic society are considered to represent a reserve for wastes and secondary resources. From the viewpoints of proper disposal and reutilization of stocked materials, accurate estimation of the amount of materials that will emerge as wastes or secondary resources in the future is important. We defined materials that have a high probability of emerging as wastes or secondary resources as “potential wastes and secondary resources” and estimated that amount for construction minerals in Japan as a case study. The following conclusions were drawn. (1) We classified materials that are input into economic society into four categories: potential wastes and secondary resources, potential dissipated materials, dissipatively used materials, and permanent structures. By clarifying the latter three non-potential wastes and secondary resources, we performed a more accurate assessment of the wastes and secondary resources that will emerge in the future. (2) The share of potential wastes and secondary resources was estimated to be about 30% of all construction minerals that have been input into and accumulated in Japanese economic society. (3) Information related to potential dissipated materials and dissipatively used materials will provide fundamental knowledge to support analyses of the environmental impacts and resource losses which these materials might generate.     

Determination and potential importance of diterpene (kaur-16-ene) emitted from dominant coniferous trees in Japan

Reactive volatile organic compounds (VOCs) are known to affect atmospheric chemistry. Biogenic VOCs (BVOCs) have a significant impact on regional air quality due to their large emission rates and high reactivities. Diterpenes (most particularly, kaur-16-ene) were detected in all of the 205 enclosure air samples collected over multiple seasons at two different sites from Cryptomeria japonica and Chamaecyparis obtusa trees, the dominant coniferous trees in Japan,. The emission rate of kaur-16-ene, was determined to be from 0.01 to 7.1 μg dwg⁻¹ h⁻¹ (average: 0.61 μg dwg⁻¹ h⁻¹) employing branch enclosure measurements using adsorbent sampling followed by solid phase-liquid extraction techniques. The emission rate was comparable to that of monoterpenes, which is known major BVOC emissions, collected from the same branches. In addition, total emission of kaur-16-ene at 30 °C was estimated to exceed that of total anthropogenic VOC emissions.     

Crystallization Behavior and Dynamic Mechanical Properties of Poly(l-Lactic Acid) with Poly(Ethylene Glycol) Terminated by Benzoate

Effect of the addition of poly(ethylene glycol) terminated by benzoate (PEG-BA) on the crystallization behavior and dynamic mechanical properties of poly(l-lactic acid) PLLA is studied as compared with poly(ethylene glycol) (PEG-OH). It is found that PEG-BA is miscible with PLLA and shows good plasticizing effect. Because PEG-OH having the same degree of polymerization is immiscible with PLLA, the end group in PEG-BA, i.e., benzoate, plays an important role in the miscibility. Furthermore, PEG-BA does not induce the PLLA degradation at melt-processing, whereas PEG-OH leads to the hydrolysis degradation. Finally, the addition of PEG-BA pronounces the crystallization rate of PLLA at low crystallization temperatures and thus enhances the degree of crystallinity at conventional processing. Consequently, the temperature dependence of dynamic mechanical properties are similar to that for isotactic polypropylene.