Proposing of new building scheme and composite towards global warming mitigation for Malaysia

The building sector has been regarded as a potential sector where there is large capacity to reduce the climate change effect. This study has proposed solutions to mitigate environmental impacts and achieve low CO₂ emission from residential sector. Therefore, full life cycle assessment (LCA) has been run to assess the CO₂ emission and its effect on the atmosphere and climate change. Based on the result, timber scheme is the best choice due to releasing less CO₂ emissions to the atmosphere. However, house builders in Malaysia have almost completely neglected timber as a building material, with timber use as building components reduced to 5%. In this study, LCA Software was used to assess CO₂ emissions from different wall construction. The alternative building scheme has been made by reinforce steel stud, wooden beam and timber wall (S8) to improve the scheme deficiency while releasing less CO₂ emissions compared to other schemes. Therefore, S8 has a decreased CO₂ effect by 85% less than precast concrete frame and 90% less than brick over their lifetime. (S8) increased the load bearing compared to conventional timber beam. Thus, new scheme S8 could be replaced by current scheme and promote more adjustable scheme for Malaysian housing.     

Sisal/Carbon Fibre Reinforced Hybrid Composites: Tensile, Flexural and Chemical Resistance Properties

The variation of mechanical properties such as tensile and flexural properties of randomly oriented unsaturated polyester based sisal/carbon fibre reinforced hybrid composites with different fibre weight ratios have been studied. The chemical resistance test of these hybrid composites to various solvents, acids and alkalies were studied. The effect of NaOH treatment of sisal fibres on the tensile, flexural and chemical resistance properties of these sisal/carbon hybrid composites has also been studied. The hybrid composites showed an increase in tensile and flexural properties with increase in the carbon fibre loading. The tensile properties and flexural properties of these hybrid composites have been found to be higher than that of the matrix. Significant improvement in tensile properties and flexural properties of the sisal/carbon hybrid composites has been observed by alkali treatment. The chemical resistance test results showed that these untreated and alkali treated hybrid composites are résistance to all chemicals except carbon tetra chloride. Hand lay-up technique was used for making the composites and tests are carried out by using ASTM methods.     

Invasive plants as biosorbents for environmental remediation: a review

Environmental Chemistry Letters - Water contamination is an environmental burden for the next generations, calling for advanced methods such as adsorption to remove pollutants. For instance,...     

Hybrid Composites Made from Oil Palm Empty Fruit Bunches/Jute Fibres: Water Absorption,Thickness Swelling and Density Behaviours

In this research, hybrid composite materials were prepared from combination of oil palm Empty fruit bunches (EFB) fibre and jute fibre as reinforcement, epoxy as polymer matrix. This study intended to investigate the effect of jute fiber hybridization and different layering pattern on the physical properties of oil palm EFB-Epoxy composites. Water absorption and thickness swelling test reveal that hybrid composite shows a moderate water absorption which is 11.20% for hybrid EFB/Jute/EFB composite and 6.08% for hybrid Jute/EFB/Jute composite. The thickness swelling and water absorption of the hybrid composites slightly increased as the layering pattern of hybrid composites changed. Hybrid composites are more water resistance and dimensional stable compare to the pure EFB composites. This is attributed to the more hydrophilic nature of EFB composites. Hybridization of oil palm EFB composites with jute fibres can improve the dimensional stability and density of pure EFB and Jute fibre reinforced composites has higher density of 1.2 g/cm³ compared to all other composites.     

Heavy metals distribution and risk assessment in soils affected by tannery effluents

Effluents collected from tanneries in Sialkot showed considerably higher levels of heavy metals. Sodium (12 660.91 mg/L) among macronutrients and Cr (592.20 mg/L) among heavy metals were found in the highest concentrations. Effluent parameters, i.e. biological oxygen demand (BOD; 12.40), chemical oxygen demand (COD; 16.53), Cd (5.90), Cr (592.20) and Fe (18.59) were the respective times higher than Pakistan National Environmental Quality Standards and their continuous unchecked discharge into agricultural soils poses a potential risk. Mean concentrations (mg/L) of Cr (592.20), Ni (2.66), Mn (1.16), Fe (37.17), Zn (0.90), Cd (0.59) and Pb (1.18) in this study exceeded levels recorded to date from different tanning hubs in Pakistan. Factor analysis/principal components analysis (FA/PCA) for the effluent parameters resulted in six varimax factors, i.e. VF1 (salinity, electrical conductivity, total dissolved solids, chloride, phosphate, BOD and COD; including characteristic tannery effluent features), VF2 (pH, Cr and alkalinity; tanning operations), VF3 (Cd and Pb; dyeing processes), VF4 (Mn and Fe; finishing operations), VF5 (Ni; retaining processes) and VF6 (hardness, Ca and Cu; bating processes). Cluster analysis performed on metal data resulted in three clusters confirming metal–metal relations obtained either from FA/PCA or a correlation matrix. The results of this study are useful for heavy metal source apportionment, assessment of risk to peripheral soils and the future management of environments around tanneries.     

Performance of photocatalytic reactors using immobilized TiO2 film for the degradation of phenol and methylene blue dye present in water stream

TiO2 thin film photocatalyst was successfully synthesized and immobilized on glass reactor tube using sol-gel method. The synthesized TiO2 coating was transparent, which enabled the penetration of ultra-violet (UV) light to the catalyst surface. Two photocatalytic reactors with different operating modes were tested: (a) tubular photocatalytic reactor with re-circulation mode and (b) batch photocatalytic reactor. A new proposed TiO2 synthesized film formulation of 1 titanium isopropoxide: 8 isopropanol: 3 acetyl acetone: 1.1 H2O: 0.05 acetic acid (in molar ratio) gave excellent photocatalytic activity for degradation of phenol and methylene blue dye present in the water. The half-life time, t1/2 of photocatalytic degradation of phenol was 56 min at the initial phenol concentration of 1000 microM in the batch reactor. In the tubular photocatalytic reactor, 5 re-circulation passes with residence time of 2.2 min (single pass) degraded 50% of 40-microM methylene blue dye. Initial phenol concentration, presence of hydrogen peroxide, presence of air bubbling and stirring speed as the process variables were studied in the batch reactor. Initial methylene blue concentration, pH value, light intensity and reaction temperature were studied as the process variables in the tubular reactor. The synthesized TiO2 thin film was characterized using SEM, XRD and EDX analysis. A comparative performance between the synthesized TiO2 thin film and commercial TiO2 particles (99% anatase) was evaluated under the same experimental conditions. The TiO2 film was equally active as the TiO2 powder catalyst.     

Influence of polymethyl acrylate additive on the formation of particulate matter and NOX emission of a biodiesel–diesel-fueled engine

Environmental Science and Pollution Research - The aim of this study is to investigate the effect of the polymethyl acrylate (PMA) additive on the formation of particulate matter (PM) and nitrogen...     

High dechlorination of PCBs catalysed by carbon under mild conditions

This article reports high dechlorination of toxic polychlorinated biphenyls (PCBs) under mild conditions. PCBs are priority pollutants acting as endocrine disruptors, human carcinogens and environmental estrogens. Previous remediation methods involving high temperature and pressure have drawbacks such as high cost, de novo dioxins synthesis and difficult recovery of vaporized PCBs. On the other hand, dechlorination methods using mild conditions show the problem of catalyst deactivation. Here, activated carbon was used for the first time as catalyst to dechlorinate 2,4,5 trichlorobiphenyl. High dechlorination, of 87%, was achieved under mild conditions. 2,4,5 trichlorobiphenyl was treated at 40–150°C with calcium hydroxide, sodium hydroxide and sulfur in mixed water and organic solvents. Dechlorination products were biphenyl, orthohydroxy biphenyls, 2,4 dihydroxy biphenyls and biphenyl-2-thiol. Dichlorobiphenyl and orthochlorobiphenyls were found in trace quantities. We found that carbon particles catalysed dechlorination by substitution reactions and suppressed further chlorination. Dechlorination at biphenyl ortho position was preceded by substitution reaction by hydroxyl and thiol ions. Moreover, in the absence of carbon, dechlorination was lower and substituted products were not observed. These findings may be applied at industrial scale to remediate PCB-contaminated waste.