Effectiveness of UV/SO32− advanced reduction process for degradation and mineralization of trichlorfon pesticide in water: identification of intermediates and toxicity assessment

Environmental Science and Pollution Research - This study aimed to investigate the degradability, mineralization, proposed decomposition pathway, intermediate products, and toxicity of effluent...     

Upper trapezius fatigue in carpet weaving: the impact of a repetitive task cycle

Introduction. Shoulder disorders are one of the most prevalent musculoskeletal disorders among carpet weavers. The most important cause of these disorders is muscle fatigue. The aim of the present study is to investigate the effect of carpet weaving characteristics on upper trapezius (UTr) muscle fatigue during a task cycle. Method. In this cross-sectional study, 9 women and 3 men participated. During an 80-min cycle of carpet weaving, a times-series model was applied to assess electromyography amplitude and frequency changes. Result. According to the joint analysis of electromyogram spectrum and amplitude method, the participants experienced 0% force decrease, 0.9% recovery, 18% force increase and 72% fatigue in the left UTr. Furthermore, the rates of force decrease, recovery, force increase and fatigue in the right UTr were 18%, 18%, 18% and 45%, respectively. Fatigue in the right and the left UTr was reported to be the dominant state during one carpet weaving task cycle. Conclusion. Task cycle appears to have a significant impact on UTr fatigue in participants, and UTr fatigue can be considered a serious risk factor in shoulder musculoskeletal disorders. Hence, further studies should focus on better workstations and work–rest periods during various subtasks.     

Density assessment and mapping of microorganisms around a biocomposting plant in Sanandaj,Iran

Exposure to microorganisms can cause various diseases or exacerbate the excitatory responses, inflammation, dry cough and shortness of breath, reduced lung function, chronic obstructive pulmonary disease, and allergic response or allergic immune. The aim of the present study was to investigate the density of microorganisms around the air of processing facilities of a biocomposting plant. Each experiment was carried out according to ASTM E884-82 (2001) method. The samples were collected from inhaled air in four locations of the plant, which had a high traffic of workers and employees, including screen, conveyor belt, aerated compost pile, and static compost pile. The sampling was repeated five times for each location selected. The wind speed and its direction were measured using an anemometer. Temperature and humidity were also recorded at the time of sampling. The multistage impactor used for sampling was equipped with a solidified medium (agar) and a pump (with a flow rate of 28.3 l/m) for passing air through the media. It was found that the mean density of total bacteria was >1.7 × 10³ cfu/m³ in the study area. Moreover, the mean densities of fungi, intestinal bacteria (Klebsiella), and Staphylococcus aureus were 5.9 × 10³, 3.3 × 10³, and 4.1 × 10³ cfu/m³, respectively. In conclusion, according to the findings, the density of bacteria and fungi per cubic meter of air in the samples collected around the processing facilities of the biocomposting plant in Sanandaj City was higher than the microbial standard for inhaled air.     

Treatment of Olefin plant spent caustic by combination of Fenton-like and foam fractionation methods in a bench scale

Environmental Science and Pollution Research - Spent Merox caustic (SMC) is a hazardous waste that is produced during the Merox desulfurization process in the petroleum refinery industry and should...     

Photoelectrochemical treatment of ammonium using seawater as a natural supporting electrolyte

In the present study, a photoelectrochemical process containing seawater as a natural low-cost supporting electrolyte was used to remove ammonium from wastewater in a continuous flow mode. Based on central composite design (CCD), response surface methodology (RSM) was employed to evaluate the performance of the process in ammonia removal. The effect of four main independent parameters, including initial ammonium concentration, hydraulic retention time (HRT), current intensity and initial pH on the removal of ammonia was evaluated by the model. The optimal initial ammonium concentration, HRT, current intensity and initial pH were 917 mg NH ₄? N;·L ^?1, 108 min, 1.8 A and 8.4, respectively. The high coefficients (R ²=0.97 and adjusted R ²=0.94) obtained by the analysis of variance (ANOVA) demonstrated close correlation between predicted and experimental values. Also, treating the reject water from the sludge dewatering unit as an ammonium-rich wastewater showed the effectiveness of the process for treating real wastewaters (86% ammonium removal). The results revealed that the present process can be an efficient method for ammonium removal from polluted effluents in coastal areas based on the availability of seawater as a cost-efficient supporting electrolyte.     

Evaluation of bio-aerosols type,density, and modeling of dispersion in inside and outside of different wards of educational hospital

Environmental Science and Pollution Research - Exposure to bioaerosols in the air of hospitals is associated with a wide range of adverse health effects due to the presence of airborne...     

Determining the most suitable areas for artificial groundwater recharge via an integrated PROMETHEE II-AHP method in GIS environment (case study: Garabaygan Basin, Iran)

Flood spreading is a suitable strategy for controlling and benefiting from floods. Selecting suitable areas for flood spreading and directing the floodwater into permeable formations are amongst the most effective strategies in flood spreading projects. Having combined geographic information systems (GIS) and multi-criteria decision analysis approaches, the present study sought to locate the most suitable areas for flood spreading operation in the Garabaygan Basin of Iran. To this end, the data layers relating to the eight effective factors were prepared in GIS environment. This stage was followed by elimination of the exclusionary areas for flood spreading while determining the potentially suitable ones. Having closely examined the potentially suitable areas using the Preference Ranking Organization Method for Enrichment Evaluations (PROMETHEE) II and analytic hierarchy process (AHP) methods, the land suitability map for flood spreading was produced. The PROMETHEE II and AHP were used for ranking all the alternatives and weighting the criteria involved, respectively. The results of the study showed that most suitable areas for the artificial groundwater recharge are located in Quaternary Q_g and Q^gsc geologic units and in geomorphological units of pediment and Alluvial fans with slopes not exceeding 3 %. Furthermore, significant correspondence between the produced map and the control areas, where the flood spreading projects were successfully performed, provided further evidence for the acceptable efficiency of the integrated PROMETHEE II-AHP method in locating suitable flood spreading areas.