Root penetration through sealing layers at mine deposit sites.

To prevent acid mine drainage arising from oxygen and water penetration of sulphide-rich mine tailings, the tailings are covered with layers of dry sealing material. Plant roots have a great ability to penetrate dense materials, and if the roots are able to penetrate the sealing layer of a tailings deposit, its oxygen-shielding properties could be reduced. The objective of this study was to evaluate whether plant roots are able to penetrate sealing layers covering mine tailings deposits. Root penetration into layers of various sealing materials, such as clayey moraine (clay, 8-10%; silt, 22-37%; sand, 37-55%; gravel, 15-18%), moraine (unspecified), 6-mm bentonite (kaolin clay) fabric, lime and clay, Cefyll (mixture of pulverized coal fly ash, cement and water) and a mixture containing biosludge (30-35%) and bioashes (65-70%), was investigated. In the field, roots were studied by digging trenches alongside vegetation growing in 3- and 10-year-old mine sites. In the greenhouse root growth of Betula pendula, Pinus sylvestris, Poa pratensis and Salix viminalis were studied in compartments where the plants had been growing for 22 months. The results from the field experiment indicated that roots are able to penetrate both deep down in the cover layer (1.7 m) and also into the sealing layers of various materials, and even to penetrate hard Cefyll. The addition of nutrients in the top cover reduced deep root growth and thereby also penetration through the sealing layer. Low hydraulic conductivity of the sealing layer or a thick cover layer had less effect on root penetration. In the greenhouse experiment roots did not penetrate the thin bentonite fabric, due to low pH (2.1-2.7) that was created from the underlying weathered mine tailings. The clayey moraine was penetrated by all species used in the greenhouse experiment; Pinus sylvestris had the greatest ability to penetrate. To prevent root penetration of the other sealing layer, a suitable condition for the plants should be created in the upper part of the cover layer, namely a sufficient amount of plant nutrients. However, to define such a condition is difficult since different plant species have different requirements.     

Fetal cardiac anomalies and genetic syndromes

Cardiac anomalies may occur in isolation or can be part of a genetic syndrome. In this article, we describe some of the genetic syndromes commonly associated with cardiac anomalies where there are other sonographic features that may aid accurate prenatal diagnosis. Copyright © 2004 John Wiley & Sons, Ltd.     

Effects of calcium hydroxide and calcium chloride addition to bentonite in iron ore pelletization.

Pyrite ash is created as waste from the roasting of pyrite ores during the production of sulphuric acid. These processes generate great amounts of pyrite ash waste that is generally land filled. This creates serious environmental pollution due to the release of acids and toxic substances. Pyrite ash waste can be utilized in the iron production industry as a blast furnace feed to process this waste and prevent environmental pollution. The essential parameters affecting the pelletization process of pyrite ash were studied using bentonite as a binder. Experiments were then carried out using bentonite and a mixture of bentonite with calcium hydroxide and calcium chloride in order to make the bentonite more effective. The metallurgical properties of pyrite ash, bentonite, calcium hydroxide, calcium chloride, a mixture of these and sintered pellets were studied using X-ray analysis. The crushing strength tests were carried out to investigate the strength of pyrite ash waste pellets. The results of these analyses showed that pyrite ash can be agglomerated to pellets and used in the iron production industry as a blast furnace feed. The crushing strength of the pellets containing calcium hydroxide and calcium chloride in addition to bentonite was better than the strength of pellets prepared using only bentonite binder.     

Working backwards to move forwards: Graph-based connectivity metrics for reserve network selection

In this paper we apply graph theory in a reserve selection exercise to explore the tradeoffs between maintaining connectivity and minimizing the total area of a protected area network. Rather than focus on a single organism, we used a multi-species approach and looked at the tradeoff curves for organisms with varying dispersal abilities. We first generated the tradeoff curves using a graph-based metric to determine the importance of individual patches for maintaining connectivity. We then performed an analogous set of analyses using patch size as a surrogate measure of importance.     

A modular approach to Integrated Assessment modeling

In this paper, we present a new approach to model coupling that probably forms the methodological basis of a new generation of Integrated Assessment models. This approach respects the knowledge and expertise that is embodied in existing models and encourages their gradual evolution. Modularity is the guiding principle. Our approach is distinguished by the way modules are coupled which is based on an interplay of a job control module, a numerical coupling module, and a couple of stand-alone functional modules. The numerical coupling module - the core component - serves to treat the feedbacks between the functional modules. A first implemented example that couples an economic and a climate module by means of a two-phase meta-optimization is presented here. The algorithm and mathematical structure behind are discussed as well as important features such as convergence behavior and reliability.     

Factor analysis of trace-element data from tree-bark samples in The Netherlands

Monte Carlo-assisted factor analysis has been applied to a data set of 20 trace-element concentrations in tree-bark samples obtained from 123 locations in The Netherlands, with the aim to investigate the suitability of bark as a biomonitor for air pollution. A Monte Carlo approach was used to give more insight to the uncertainties and significance levels of the factor analysis results. Notwith-standing a rather strong influence of soil material on the concentration levels, factor analysis enabled the identification of five significant pollution source types, all of which corresponded with source types found in an earlier biomonitoring study in The Netherlands using epiphytic lichens. A more detailed comparison with the lichen results showed a remarkable difference in lead concentrations between bark and lichen. It was concluded that bark can be successfully employed as a biomonitor for air pollution. The power of factor analysis to adequately determine the soil contribution may render extensive sample washing procedures superfluous.     

Optimizing the removal of small fish passage barriers

Removing small artificial barriers that hinder upstream migrations of fish is a major problem in riparian habitat restoration. Because of budgetary limitations, it is necessary to prioritize barrier removal and repair decisions. These have usually been based on scoring and ranking procedures, which, although simple to use, can be very inefficient in terms of increasing the amount of accessible instream habitat. We develop a novel decision-making approach, based on integer programming techniques, which optimizes repair and removal decisions. Results show based on real datasets of barrier culverts located in Washington State that scoring and ranking is over 25% below the optimum on average and a full 100% below in the worst case, producing no net habitat gain whatsoever. This is compared to a dynamic programming method that was able to find optimal solutions in less than a second, even for problems with up to several hundred variables, and a heuristic method, which found solutions with less than a 1% average optimality gap in even less time.     

Ecoprofit-Styria-prepare Thirteen pollution prevention case studies in the Styrian industry

The paper focuses upon the organization of a federal state-funded pollution prevention project in the Styrian industry. The project includes 13 companies from the textile, pulp and paper, machine building, wood working and printed circuit board manufacturing industries, covering most of the sectors and sizes in the Styrian industry. It started in January 1994 and will last for one year. It will demonstrate the possibilities of pollution prevention and the need for further research work. This project will make use of the methods and tools that were refined in the Austrian Prepare project. As a first step, a systematic balance of all the inputs and outputs of a company is made, after which the weak points and inefficiencies of material and energy use are identified and the options for improvements, both economical and ecological, are defined. Consequently, modifications in products and production lead to a situation with less waste and emissions. The preliminary lessons from these projects are presented: as a rule, the utilities (consumption of process materials and water, cleaning, energy, preparatory and finishing steps) are treated as black boxes and usually represent a considerable optimization potential. In these areas especially there is usually a lack of information and coordination as well as a need for a systematic and comprehensive approach. Leadership in the company and creative consultants are needed for starting lasting successful pollution prevention projects.