The COVID-19 pandemic: prediction study based on machine learning models

Environmental Science and Pollution Research - COVID-19 was first discovered in Wuhan, China in December 2019. It is one of the worst pandemics in human history. Recent studies reported that...     

Pd-MnO2 nanoparticles/TiO2 nanotube arrays (NTAs) photo-electrodes photo-catalytic properties and their ability of degrading Rhodamine B under visible light

Pd-MnO_2/TiO_2 nanotube arrays(NTAs) photo-electrodes were successfully fabricated via anodization and electro deposition subsequently; the obtained Pd-MnO_2/TiO_2 NTAs photo electrodes were analyzed by scanning electron microscopy(SEM), X-ray diffraction(XRD) and characterized accordingly. Moreover, the light harvesting and absorption properties were investigated via ultraviolet–visible diffuse reflectance spectrum(DRS); photo degradation efficiency was investigated via analyzing the photo catalytic degradation of Rhodamine B under visible illumination(xenon light). The performed analyses illustrated that Pd-MnO_2 codoped particles were successfully deposited onto the surface of the TiO_2 nanotube arrays;DRS results showed significant improvement in visible light absorption which was between400 and 700 nm. Finally, the photo catalytic degradation efficiency results of the designated organic pollutant(Rhodamine B) illustrated a superior photocatalytic(PC) efficiency of approximately 95% compared to the bare TiO_2 NTAs, which only exhibited a photo catalytic degradation efficiency of approximately 61%, thus it indicated the significant enhancement of the light absorption properties of fabricated photo electrodes and their yield of UOH radicals.     

Performance of Cow Dung Reinforced Biodegradable Poly(Lactic Acid) Biocomposites for Structural Applications

In this work, performance of cow dung (CD) reinforced poly(lactic acid) (PLA) biocomposites was investigated for the potential use in load bearing application. CD of average 4 mm size was blended with PLA at different CD ratios (0–50 wt%) and their effects on the biocomposite properties were studied. The results showed an improvement in the flexural properties, while the tensile and impact strength dropped by 20 and 28% with the addition of 50% CD. The decline in the tensile and impact strength was due to micro-cracking and voids formation at higher CD content. Also, the incorporation of CD slightly decreased the thermal stability of the biocomposite. However, dynamic mechanical properties of the biocomposites generally improved. SEM analysis of tensile and impact fractured surfaces indicated that the CD had a reasonable adhesion with matrix. Moreover, the SEM micrographs of soil burial studies showed an accelerated degradation of higher CD wt% biocomposites.     

Molecular,functional, and cellular alterations of oocytes and cumulus cells induced by heat stress and shock in animals

Environmental Science and Pollution Research - Global warming is considered as the main environmental stress affecting ecosystems as well as physiological and biochemical characteristics, and...     

Protective effects of thymoquinone against acrylamide-induced liver,kidney and brain oxidative damage in rats

Environmental Science and Pollution Research - Acrylamide (AA), an industrial monomer, may cause multi-organ toxicity through induction of oxidative stress and inflammation. The antioxidant...     

Value addition in the services sector and its heterogeneous impacts on CO2 emissions: revisiting the EKC hypothesis for the OPEC using panel spatial estimation techniques

Environmental Science and Pollution Research - This study examines the Environmental Kuznets Curve (EKC) hypothesis in the context of 12 members of the OPEC by utilizing data on both the aggregate...     

Chlorination Byproducts in Drinking Water Produced from Thermal Desalination in United Arab Emirates

Oil activities in the Arabian Gulf can potentially affect the quality of the intake water available for coastal desalination plants. This paper addresses such situation by investigating the quality of intake water and desalinated water produced by a desalination plant located near a coastal industrial complex in United Arab Emirates (UAE). Analyses of the organic compounds on the intake seawater reported non-detected levels in most samples for the three tested organic groups; namely Polyaromatic Hydrocarbons (PAHs), Phenols, and Polychlorinated Biphenyls (PCBs). Trihalomethanes (THMs) and Haloacetic Acids (HAAs) were also tracked in the intake sea water, throughout the desalination processes, and in the final produced drinking water, to evaluate the undertaken pre- and post chlorination practices. The levels of considered Chlorination Byproducts (CBPs) were mostly found below the permissible international limits with few exceptions showing tangible levels of bromoform in the intake seawater and in the final produced drinking water as well. Lab-controlled experiments on the final produced distillate showed little contribution of its blending with small percentage of seawater upon the formation of trihalomethane and in particular, bromoform. Such results indicate that the organic precursors originated in the seawater are responsible for bromoform formation in the final distillate.     

Influence of preparation method on structural,optical, magnetic,and adsorption properties of nano-NiFe2O4

Nickel ferrite (NiFe₂O₄) nanoparticles are prepared through different routes (microwave, co-precipitation, and pyrolysis) and tested for water purification applications through adsorption removal of an acid red dye B as a model organic pollutant. The characterizations of the prepared samples were done using XRD, FT-IR, SEM, TEM, BET, UV-Vis absorbance, Raman spectrum, and vibrating sample magnetometer (VSM). All samples showed an inverse spinel crystal structure. The obtained results pointed out to the effect of the synthetic route on the morphology, particle size, optical, and magnetic properties of the prepared ferrites. Magnetic measurements showed super-paramagnetic behavior for all samples. The magnetic saturation (M_s) of the sample prepared by pyrolysis, was found to possess the highest saturation value, 34.8 emu/g. Adsorption experiments were performed under the change in several parameters, such as pH, adsorbent dosage, and initial dye concentration. A dye removal percentage of 99% was reached under the optimum state. The isothermal adsorption of the acid red dye was investigated using several models, in which the experimental data could be best described by the Freundlich model. Several kinetic and equilibrium models were inspected by linear regression analysis and showed best fitting for the adsorption data through pseudo-second-order model. The calculated thermodynamic parameters indicated that the adsorption of acid red dye onto all the ferrite samples is a spontaneous and endothermic physical adsorption process.

     

Minimization of the formation of disinfection by-products

The drinking water industry is required to minimize DBPs levels while ensuring adequate disinfection. In this study, efficient and appropriate treatment scheme for the reduction of disinfection by-product (DBPs) formation in drinking water containing natural organic matter has been established. This was carried out by the investigation of different treatment schemes consisting of enhanced coagulation, sedimentation, disinfection by using chlorine dioxide/ozone, filtration by sand filter, or granular activated carbon (GAC). Bench scale treatment schemes were applied on actual samples from different selected sites to identify the best conditions for the treatment of water. Samples were collected from effluent of each step in the treatment train in order to analyze pH, UV absorbance at 254 nm (UVA₂₅₄), specific UV absorbance at 254 nm (SUVA₂₅₄), dissolved organic carbon (DOC), haloacetic acids (HAAs) and trihalomethanes (THMs). The obtained results indicated that using pre-ozonation/enhanced coagulation/activated carbon filtration treatment train appears to be the most effective method for reducing DBPs precursors in drinking water treatment.     

Heterogeneous photocatalytic degradation of pesticides using decatungstate intercalated macroporous layered double hydroxides

Decatungstate W₁₀O₃₂ ^4? was efficiently intercalated between the layers of three-dimensionally ordered macroporous Mg₂Al-layered double hydroxide. The structural and textural properties of as-prepared intercalated compound were characterized using different solid-state characterization techniques such as X-ray powder diffraction, FTIR and Raman spectroscopies and electronic microscopy. The photocatalytic properties of immobilized W₁₀O₃₂ ^4? within Mg₂Al structure were investigated using 2-(1-naphthyl) acetamide (NAD) as a model of pesticide. The influence of different parameters such as amount of catalyst, pH and oxygen concentration were investigated. An optimal NAD degradation was obtained for a photocatalyst concentration of 60 mg l^?1. Under our experimental conditions, this heterogeneous photocatalyst induces photodegradation of 60 % of NAD after 17 h of irradiation at 365 nm and at pH 6.6. Interestingly, pesticide photodegradation leads to the mineralization of substrates to H₂O and CO₂ and the photocatalyst can be recycled and reused without any loss of activity over four cycles.