Prenatal diagnosis using deletion studies in Duchenne muscular dystrophy

Accurate carrier testing and prenatal diagnosis in Duchenne muscular dystrophy (DMD) families is facilitated when an Xp21 deletion is found to be segregating within a family. We discuss the results of the DNA testing in two families, one in which DNA from affected males was available for study and the other in which no DNA from an affected male was available. Factors complicating the counselling of DMD deletion families are outlined.     

Sludge-grown algae for culturing aquatic organisms: Part II. Sludge-grown algae as feeds for aquatic organisms

This project investigated the feasibility of using sewage sludge to culture microalgae (Chlorella-HKBU) and their subsequent usage as feeds for rearing different organisms. Part II of the project evaluated the results of applying the sludge-grown algae to feedOreochromis mossambicus (fish),Macrobrachium hainenese (shrimp), andMoina macrocopa (cladocera). In general, the yields of the cultivated organisms were unsatisfactory when they were fed the sludge-grown algae directly. The body weights ofO. mossambicus andM. macrocopa dropped 21% and 37%, respectively, although there was a slight increase (4.4%) inM. hainenese. However, when feeding the algal-fed cladocerans to fish and shrimp, the body weights of the fish and shrimp were increased 7% and 11% accordingly. Protein contents of the cultivated organisms were comparable to the control diet, although they contained a rather high amount of heavy metals. When comparing absolute heavy metal contents in the cultivated organisms, the following order was observed: alga > cladocera > shrimp, fish > sludge extracts. Bioelimination of heavy metals may account for the decreasing heavy metal concentrations in higher trophic organisms.     

Facile Preparation of Chitosan Films for High Performance Removal of Reactive Blue 19 Dye from Aqueous Solution

This study aimed at finding effective strategies for high-performance removal of reactive blue 19 (RB19) dye from aqueous solution. Chitosan (CS) films had been prepared by using solvent casting with mild drying for this purpose. The CS films were characterized by X-ray diffraction, field-emission scanning electron microscopy, and Fourier transform infrared (FTIR) spectroscopy. The performance of RB19 removal using CS were evaluated by varying contact time, solution pH, initial dye concentration, and adsorbent dosage. Adsorption isotherms, kinetics, and desorption were investigated by batch experiments. Results showed that CS films exhibited the optimal adsorption performance for RB19 removal and high maximum adsorption capacities of RB19, which were 799 and 822.4 mg g^?1 at 20 and 40 °C, respectively. Adsorption kinetic data were well described by the pseudo-second-order kinetic model. FTIR analyses further indicated that interactions between RB19 and the CS film occurred during adsorption. The CS films also exhibited satisfactory desorption of RB19 at about 80 % after 30 min of desorption at pH 11. Our study demonstrated that the CS films can be easily prepared and applied for effective removal of RB19 in treatment of wastewater.     

Sorbent-based devices for the removal of spilled oil from water: a review

Environmental Science and Pollution Research - Always, oil spills do cause serious and dire consequences for the environment, nature, and society that it consumes much time and socio-economic...     

铁阳极电解脱色直接黄11染料模拟废水

研究采用铁为阳极电化学法处理直接黄11染料模拟废水脱色性能的影响进行研究。影响因素包括:电流密度、pH值、染料浓度和电解质浓度。研究结果表明,电流密度大有利于染料废水脱色,但能耗消耗大;初始溶液在中性条件下不仅取得很好的处理效果,而且脱色能耗较低;随着染料初始浓度增加脱色率和脱色能耗降低的趋势;随着电解质浓度升高染料脱色率下降的趋势,脱色能耗先减少,然后缓慢增大。在染料初始浓度50 mg/L、pH值为7.11、电流密度2.083 mA/cm2、电解质Na2SO4浓度0.01 mol/L、温度20℃、搅拌速度600 r/min、电解时间60min条件下,脱色率达到92.2%,脱色能耗1.709 kW.h/kg染料。     

A systemic health risk assessment for the chromium cycle in Taiwan

Health risk assessment (HRA) has been recognized as a useful tool for identifying health risks of human activities. In particular, this method has been well applied to spatially defined units, such as a production plant, a treatment facility, and a contaminated site. However, the management strategies based on the risk information will be more efficient if the comprehensive picture of total risks from all kinds of sources is depicted. In principle, the total risks can be obtained when all risk sources are assessed individually. Apparently, this approach demands huge amount of efforts. This study develops a methodology that combines substance flow and risk estimation to facilitate examination of risk in a systemic way and provide comprehensive understanding of risk generation and distribution corresponding to flows of substances in the anthroposphere and the environment. Substance flow analysis (SFA) and HRA method is integrated to produce a systemic risk assessment method, from which substance management schemes can be derived. In this study, the chromium cycle in Taiwan is used as an example to demonstrate the method, by which the associated substance flow in the economy and the risk caused by the substance in the environmental system is determined. The concentrations of pollutants in the environmental media, the resultant risks and hazard quotients are calculated with the widely-used CalTOX multimedia model.     

Surface functional characteristics (C, O, S) of waste tire-derived carbon black before and after steam activation

The effects of steam activation on the surface functional characteristics of waste tire-derived carbon black were investigated. Two carbon-based materials, powdered carbon black (PCB) and PCB-derived powdered activated carbon (PCB-PAC), were selected for this study. A stainless steel tubular oven was used to activate the PCB at an activation temperature of 900 degrees C and 1 atm using steam as an activating reagent. X-ray photoelectron spectroscopy (XPS) was adopted to measure the surface composition and chemical structure of carbon surface. Various elemental spectra (C, O, and S) of each carbon sample were further deconvoluted by peak synthesis. Results showed that the surfaces of PCB and PCB-PAC consisted mainly of C-C and C-O. The PCB-PAC surface had a higher percentage of oxygenated functional groups (C=O and O-C=O) than PCB. The O1s spectra show that the oxygen detected on the PCB surface was mainly bonded to carbon (C-O), whereas the oxygen on the PCB-PAC surface could be bonded to hydrogen (O-H) and carbon (C-O). Sulfur on the surface of PCB consisted of 58.9 wt% zinc sulfide (ZnS) and 41.1 wt% S=C=S, whereas that on the surfaces of PCB-PAC consisted mainly of S=C=S. Furthermore, the increase of oxygen content from 9.6% (PCB) to 11.9% (PCB-PAC) resulted in the increase of the pH values of PCB-PAC after steam activation.