Bioaccumulation of lead and the influence of chelating agents in Catla catla fingerlings

Lead is a widespread element and one of the persistent and cumulative pollutants of the environment. The present study deals with the bioaccumulation of lead and the influence of chelating agents, meso 2,3-dimercaptosuccinic acid (DMSA), D-Penicillamine and CaNa₂EDTA in reducing the concentration of lead on the selected organs of Catla catla fingerlings for both acute and chronic exposures by using ICP-AES. It is inferred from the present findings that there was a correlation between environmental conditions and the heavy metal contents of the fish. The highest concentration of lead is found in kidney tissues and the lowest in muscle tissues. The accumulation pattern of lead in the selected organs of Catla catla is: kidney > liver > gill > brain > muscle. Also, it has been found that the treatment of chelating agents, DMSA, D-Penicillamine and CaNa₂EDTA reduces the concentration of lead significantly for both acute and chronic exposures. The results also show that DMSA is the most effective chelator of lead in reducing the body burden of C. catla fingerlings. The observed data further indicate that C. catla could be suitable for monitoring organisms to study the bioavailability of water-bound metals in freshwater habitats.     

Determination of growth rate and yield of nitrifying bacteria by measuring carbon dioxide uptake rate.

Nitrifier growth parameters--the maximum growth rate (microAmax) and yield (YA)--were estimated by measuring the rate of carbon dioxide uptake and additional rates of oxygen uptake and ammonia (or nitrite) use. Batch tests in a combined titrimetric and offgas analyzer with enriched Nitrobacter and Nitrosomonas cultures and an activated sludge sample were performed. The measured microAmax values for the Nitrobacter and Nitrosomonas cultures were 0.67 +/- 0.03 day(-1) and 0.54 +/- 0.09 day(-1), while the YA values were 0.072 +/- 0.01 g volatile suspended solids (VSS) x g nitrogen (N)(-1) and 0.14 +/- 0.02 gVSS x gN(-1), respectively. For the activated sludge sample, microAmax was observed to increase with pH (microAmax = 0.72 x 3.3(pH-7.1)) over the range 6.8 to 7.1. All microAmax and YA values determined by this method were similar to those previously reported. Compared with other microAmax and YA estimation methods, this method allows for unique microAmax and YA estimations for given conditions from a single experiment.     

Nitrite pre-treatment of dewatered sludge for microbial fuel cell application

The effect of pre-treatment of dewatered sludge using different nitrite concentrations and pH for microbial fuel cell (MFC) application was investigated. The results show that the addition of nitrite was feasible to increase the solubilization rate of the sludge and may reduce mass transfer limitation at the anode. This helped the MFC to reach higher voltage and to generate more power. The higher free nitrous acid (FNA) concentration under the acidic condition helped to increase sludge solubilization. However, under an alkaline condition, during which the FNA concentration was relatively low, the solubilization of the sludge was higher. The highest voltage and power density produced was 390?mV and 153?mW/m², respectively, with the addition of nitrite at 100?mg-N/L and pH?9. Furthermore, it was found that elevated levels of FNA could inhibit electrogenic bacteria thus reducing power generation.     

Experimental and Modeling Studies for the Removal of Crystal Violet Dye from Aqueous Solutions using Eco-friendly <Emphasis Type="Italic">Gracilaria corticata</Emphasis> Seaweed Activated Carbon/Zn/Alginate Polymeric Composite Beads

This research article describes, an eco-friendly activated carbon prepared from the Gracilaria corticata seaweeds which was employed for the preparation of biodegradable polymeric beads for the efficient removal of crystal violet dye in an aqueous solution. The presence of chemical functional groups in the adsorbent material was detected using FTIR spectroscopy. The morphology and physical phases of the adsorbent materials were analyzed using SEM and XRD studies respectively. Batch mode dye adsorption behavior of the activated carbon/Zn/alginate polymeric beads was investigated as a function of dosage, solution pH, contact time, initial dye concentration and temperature. Maximum dye removal was observed at a pH of 5.0, 1 g of adsorbent dosage with 60 mg/L dye concentration, 50 min of contact time and at 30 °C. The equilibrium modeling studies were analyzed with Freundlich and Langmuir adsorption isotherms and the adsorption dynamics was predicted with Lagergren’s pseudo-first order, pseudo-second order equations and intra particle diffusion models. The process of dye removal followed a pseudo second-order kinetics rather than pseudo first order. The thermodynamic parameters like standard Gibbs free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) were determined and the results imply that the adsorption process was spontaneous, endothermic and increases the randomness between the adsorbent and adsorbate. The results from the experimental and correlation data reveal that the Gracilaria corticata activated carbon/Zn/alginate polymeric beads have proved to be an excellent adsorbent material for the removal of CV dye.     

Self-flocculation of enriched mixed microalgae culture in a sequencing batch reactor

Environmental Science and Pollution Research - Microalgae-based biodiesel has gained widespread interest as an alternative energy source. Low-cost microalgae harvesting technologies are important...