Biodiesel production from vegetable oil and waste animal fats in a pilot plant

In this study, corn oil as vegetable oil, chicken fat and fleshing oil as animal fats were used to produce methyl ester in a biodiesel pilot plant. The FFA level of the corn oil was below 1% while those of animal fats were too high to produce biodiesel via base catalyst. Therefore, it was needed to perform pretreatment reaction for the animal fats. For this aim, sulfuric acid was used as catalyst and methanol was used as alcohol in the pretreatment reactions. After reducing the FFA level of the animal fats to less than 1%, the transesterification reaction was completed with alkaline catalyst. Due to low FFA content of corn oil, it was directly subjected to transesterification. Potassium hydroxide was used as catalyst and methanol was used as alcohol for transesterification reactions. The fuel properties of methyl esters produced in the biodiesel pilot plant were characterized and compared to EN 14214 and ASTM D6751 biodiesel standards. According to the results, ester yield values of animal fat methyl esters were slightly lower than that of the corn oil methyl ester (COME). The production cost of COME was higher than those of animal fat methyl esters due to being high cost biodiesel feedstock. The fuel properties of produced methyl esters were close to each other. Especially, the sulfur content and cold flow properties of the COME were lower than those of animal fat methyl esters. The measured fuel properties of all produced methyl esters met ASTM D6751 (S500) biodiesel fuel standards.     

Mineral contents and proximate composition of Pistacia vera kernels

The mineral contents of Pistacia vera kernels were determined by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). The minimum and maximum values of K, P, Ca, Mg, and S elements ranged from 6,333 to 8,064 mg/kg, 3,630 to 5,228 mg/kg, 1,614 to 3,226 mg/kg, 1,716 to 2,402 mg/kg, and 1,417 to 1,825 mg/kg, respectively. In addition, the mean values of Fe, Zn, Cu, Mn, B, Mo, Cr and Ni elements were determined as 42.48, 20.52, 12.81, 7.48, 11.31, 0.106, 0.511 and 1.67 mg/kg, respectively. Ash levels of kernels were found between 2.28 % (Urfa) and 2.79 % (Halebi). In addition, crude oil and protein contents were determined between 48.8 % (Halebi) to 55.3 % (Siirt) and 23.33 % (Uzun) to 27.16 % (Halebi), respectively.     

Determination of Impact of Urbanization on Agricultural Land and Wetland Land Use in Balçovas’ Delta by Remote Sensing and GIS Technique

Because of their intense vegetation and the fact that they include areas of coastline, deltas situated in the vicinity of big cities are areas of greet attraction for people who wish to get away from in a crowded city. However, deltas, with their fertile soil and unique flora and fauna, need to be protected. In order for the use of such areas to be planned in a sustainable way by local authorities, there is a need for detailed data about these regions. In this study, the changes in land use of the Balçova Delta, which is to the immediate west of Turkey’s third largest city Izmir, from 1957 up to the present day, were investigated. In the study, using aerial photographs taken in 1957, 1976 and 1995 and an IKONOS satellite image from the year 2005, the natural and cultural characteristics of the region and changes in the coastline were determined spatially. Through this study, which aimed to reveal the characteristics of the areas of land already lost as well as the types of land use in the Balçova delta and to determine geographically the remaining areas in need of protection, local authorities were provided with the required data support. Balçova consists of flat and fertile wetland with mainly citrus-fruit orchards and flower-producing green houses. The marsh and lagoon system situated in the coastal areas of the delta provides a habitat for wild life, in particular birds. In the Balçova Delta, which provides feeding and resting for migratory birds, freshwater sources are of vital importance for fauna and flora. The settlement area, which in 1957 was 182 ha, increased 11-fold up to the year 2005 when it reached 2,141 ha. On the other hand, great losses were determined in farming land, olive groves, forest and in the marsh and lagoon system. This unsystematic and rapid urbanization occurring in the study region is not only causing the loss of important agricultural land and wetland, but also lasting water and soil pollution.     

Heavy Metal Contents of the Karasu Creek Sediments, Nigde, Turkey

Heavy metal contamination in sediments of the Karasu spring was investigated in the presented study. In this respect, sediment samples were collected from contaminant sites along the spring starting from the spring water manifestation site, base of the Akkaya dam to the dam exit site. Heavy metal concentrations were determined by X-ray Fluorescence Spectrometer. Cobalt, copper, arsenic, tin, nickel, zinc, cadmium, lead, aluminum, iron, titan, chromium and manganese contents of the Karasu creek sediments are found as 18.30–69.00, 12.40–595.0 5.50–345.3, 5.80–15.1, 10.9–64.1, 28.90–103,300, 4.1–356.2, 7.70–37,840, 13,460–109,400, 11,740–62,900, 22.18–59.04, 41.70–369 and 12.09–3,480 mg/kg, respectively. Results indicate the presence of a contamination in the Karasu creek. All the metal concentrations were found to be exceeding their acceptable limit values. Eutrophication is developed in the Karasu creek and the Akkaya dam. It is thought that heavy metal accumulation in the creek is originated from discharge from mine quarries, industrial and domestic wastes. Protection zones should be defined and all necessary measures must be taken along the Karasu creek.     

The role of endogenous nitric oxide in melatonin-improved tolerance to lead toxicity in maize plants

Melatonin (MT) and nitric oxide (NO) are known as scavengers of free radicals and an antioxidant against biotic and abiotic stresses in plant defense systems. However, whether NO interplays role in MT-induced antioxidant defense remains to be determined in the plants exposed to lead (Pb) toxicity. So, two experiments were designed to evaluate the role of NO in MT-mediated tolerance of maize plants to Pb stress. In the initial experiment, prior to starting different treatments, a solution of 0.05- or 0.10-mM MT was sprayed every other day for a period of 10 days to the leaves of maize plants exposed to Pb stress (0.1-mM PbCl₂). Pb toxicity significantly caused reduction in plant biomass (both fresh and dry), PSII maximum efficiency (F_v/F_m), total chlorophyll, leaf potassium (K), calcium (Ca), and leaf water potential, but it resulted in increased levels of proline, hydrogen peroxide (H₂O₂), malondialdehyde (MDA), electron leakage (EL), leaf Pb, and endogenous NO. An addition experiment was set up to further understand whether NO played role in mitigation of Pb toxicity in maize plants by MT using scavengers of NO and cPTIO combined with the MT treatments. MT-induced tolerance to Pb toxicity was totally eliminated by cPTIO by reversing endogenous NO. The present results clearly indicated that MT mediated the endogenous NO to improve tolerance of maize plants to Pb toxicity. This evidence was also supported by the increases of H₂O₂ and MDA and reduces some antioxidant enzyme activities tested as well as the plant growth inhibition and increased leaf Pb content by application of MT combined with cPTIO.

     

Feasibility of incorporating waste grass clippings (Lolium perenne L.) in particleboard composites

This study investigated some of the important physical (thickness swelling) and mechanical (modulus of rupture, modulus of elasticity and internal bond) properties of single-layer particleboard panels made from eucalyptus (Eucalyptus camaldulensis Dehn.), waste of grass clippings (Lolium perenne L.) and combinations of the two. The chemical properties (pH, holocelluse and alpha cellulose contents, and water, alcohol-benzene and 1% sodium hydroxide solubilities) of the raw materials were also determined. Panels with a 6:94 ratio of grass-to-eucalyptus particles had the required mechanical properties for interior fitments including furniture and general uses. Boards manufactured with 100% grass clippings exhibited the lowest quality. The overall panel properties improved with a lower percentage of grass clippings added. Based on initial results, it also appears that grass should compose no more than 13% to achieve acceptable panel properties for interior fitments and general uses.     

EXPOSURE ASSESSMENT OF POPULATIONS USING ENVIRONMENTAL MODELING,DEMOGRAPHIC ANALYSIS,AND GIS1

ABSTRACT: Simulation of ground-water flow and fate of contaminants in the subsurface environment constitutes a major phase of most environmental assessment and site remediation studies. These simulation studies yield information on spatial and temporal distributions of contaminants in the subsurface media. An important use of this information is to conduct exposure assessment studies. Spatial and temporal distributions of both chemical concentrations and exposed populations render this integrated exposure analysis task rather difficult. Geographic Information Systems (GIS), on the other hand, provide a platform in which layered, spatially distributed databases can be manipulated with ease, thereby simplifying exposure analysis tasks significantly. In this paper, we describe procedures that combine the simulation models and demographic databases under a GIS platform to automate the exposure assessment phase of a typical health assessment study. Procedures developed herein significantly simplify the post-processing phase of the analysis, and render the overall task more ‘user friendly.’ A site-specific application is included as a demonstration of the proposed process.     

Bleaching of chemithermomechanical pulp (CTMP) using environmentally friendly chemicals

Increasing environmental restrictions require a reduction in the use of chlorine-containing bleaching agents mainly chlorine gas. There are several approaches to this goal, including changes in the cooking process and the influent treatment. The aim of this study is to improve the physical and optical properties of chemithermomechanical pulp (CTMP) which has low brightness and strong tendency towards aging in chlorine-free bleaching sequences. For this reason, initially 7 different sets of single stage hydrogen peroxide bleaching operations were performed. After the analysis of the data obtained, the optimum bleaching conditions were as: H2O2 ratio on oven dry (o.d) raw material: 2%, NaOH ratio (on o.d raw material): 1.5%, MgSO4 ratio (on o.d raw material) : 0.5%, Na2SiO3 ratio (on o.d raw material) : 3%, EDTA ratio (on o.d raw material) : 0.5%, reaction time: 60 minutes, reaction temperature: 70 degrees C and concentration: 16%. Then, 11 different sets of two and multistage H2O2 (P), NaBH4 (B), and Na2S2O4 (S) bleaching operations were carried out. Optimum bleaching conditions were found in bleaching of BPSP with 4 stage sequences. As a result, CTMP brightness was observed to increase from 47% to 81.37% elrepho while yellowness of bleached pulps decreased from 321 per thousand to 164.01 per thousand elrepho.