Aminobenzenesulfonamide functionalized SBA-15 nanoporous molecular sieve: A new and promising adsorbent for preconcentration of lead and copper ions

A rapid method for the extraction and monitoring of nanogram level of Pb²⁺ and Cu²⁺ ions using uniform silanized mesopor (SBA-15) functionalized with aminobenzenesulfonamide groups and flame atomic absorption spectrometry (FAAS) is presented. Aminobenzenesulfonamide functionalized SBA-15 was synthesized according to procedure in the literature and the presence of organic groups in the silica framework was demonstrated by FT-IR spectra. The functionalized product showed the BET surface area 110 m²/g and pore diameter 5.1 nm, based on adsorption-desorption of N₂ at 77 K. The effect of several variables such as (amount of adsorbent, stirring time, pH and presence of other ions in the medium) has been studied. Lead and copper were completely extracted at pH greater than 3 after stirring for 10 min. The maximum capacity of the adsorbent was found to be 191.3 ± 1.4 and 155.0 ± 1.0 μg of lead and copper ions/mg functionalized SBA-15, respectively. The preconcentration factor of the method was found to be 200. The detection limit of the technique was 3.4 and 0.4 ng/mL for Pb²⁺ and Cu²⁺, respectively. The applications of this methodology for real samples were examined by various water type, black tea and pepper samples.     

Heavy metals and their source identification in particulate matter (PM2.5) in Isfahan City, Iran

The presence of heavy metals(HMs) in particulate matters(PMs) particularly fine particles such as PM_(2.5) poses potential risk to the health of human being. The purpose of this study was to analyze the contents of HMs in PM_(2.5) in the atmospheric monitoring stations in Isfahan city,Iran, in different seasons between March 2014 and March 2015 and their source identification using principle component analysis(PCA). The samples of PM_(2.5) were taken using a high volume sampler in 7 monitoring stations located throughout the city and industrial zones since March 2014 to March 2015. The HMs content of the samples was measured using ICP-MS.The results showed that the concentrations of As, Cd and Ni were in a range of 23–36, 1–12,and 5–76 ng/m~3 at all the stations which exceeded the US-EPA standards. Furthermore,the concentrations of Cr and Cu reached to 153 and 167 ng/m~3 in some stations which were also higher than the standard levels. Depending on the potential sources of HMs, their concentration in PM_(2.5) through the various seasons was different. PCA illustrated that the different potential sources of HMs in the atmosphere, showing that the most important sources of HMs originated from fossil fuel combustion, abrasion of vehicle tires, industrial activities(e.g., iron and steel industries) and dust storms. Management and control of air pollution of industrial plants and vehicles are suggested for decreasing the risk of the HMs in the region.     

Biodegradation of low-density polyethylene (LDPE) by isolated fungi in solid waste medium

In this study, biodegradation of low-density polyethylene (LDPE) by isolated landfill-source fungi was evaluated in a controlled solid waste medium. The fungi, including Aspergillus fumigatus, Aspergillus terreus and Fusarium solani, were isolated from samples taken from an aerobic aged municipal landfill in Tehran. These fungi could degrade LDPE via the formation of a biofilm in a submerged medium. In the sterilized solid waste medium, LPDE films were buried for 100 days in a 1-L flask containing 400 g sterile solid waste raw materials at 28 °C. Each fungus was added to a separate flask. The moisture content and pH of the media were maintained at the optimal levels for each fungus. Photo-oxidation (25 days under UV-irradiation) was used as a pretreatment of the LDPE samples. The progress of the process was monitored by measurement of total organic carbon (TOC), pH, temperature and moisture. The results obtained from monitoring the process using isolated fungi under sterile conditions indicate that these fungi are able to grow in solid waste medium. The results of FT-IR and SEM analyses show that A. terreus and A. fumigatus, despite the availability of other organic carbon of materials, could utilize LDPE as carbon source. While there has been much research in the field of LDPE biodegradation under solid conditions, this is the first report of degradation of LDPE by A. fumigatus.     

Elimination of Cs+ from aquatic systems by an adsorbent prepared by immobilization of potassium copper hexacyanoferrate on the SBA-15 surface: kinetic,thermodynamic, and isotherm studies

Environmental Science and Pollution Research - For elimination of cesium from aqueous solutions, mesoporous SBA-15 was synthesized and employed as the support for immobilization of potassium copper...     

Objective approach for analysis of noise source characteristics and acoustic conditions in noisy computerized embroidery workrooms

It is highly important to analyze the acoustic properties of workrooms in order to identify best noise control measures from the standpoint of noise exposure limits. Due to the fact that sound pressure is dependent upon environments, it cannot be a suitable parameter for determining the share of workroom acoustic characteristics in producing noise pollution. This paper aims to empirically analyze noise source characteristics and acoustic properties of noisy embroidery workrooms based on special parameters. In this regard, reverberation time as the special room acoustic parameter in 30 workrooms was measured based on ISO 3382-2. Sound power quantity of embroidery machines was also determined based on ISO 9614-3. Multiple linear regression was employed for predicting reverberation time based on acoustic features of the workrooms using MATLAB software. The results showed that the measured reverberation times in most of the workrooms were approximately within the ranges recommended by ISO 11690-1. Similarity between reverberation time values calculated by the Sabine formula and measured values was relatively poor (R ²?=?0.39). This can be due to the inaccurate estimation of the acoustic influence of furniture and formula preconditions. Therefore, this value cannot be considered representative of an actual acoustic room. However, the prediction performance of the regression method with root mean square error (RMSE)?=?0.23 s and R ²?=?0.69 is relatively acceptable. Because the sound power of the embroidery machines was relatively high, these sources get the highest priority when it comes to applying noise controls. Finally, an objective approach for the determination of the share of workroom acoustic characteristics in producing noise could facilitate the identification of cost-effective noise controls.     

Prevalence of Norovirus Infection in Children and Adults with Acute Gastroenteritis,Tehran, Iran, 2008–2009

Noroviruses are one of important agents that cause acute viral gastroenteritis worldwide. These viruses are belonging to Caliciviridae family and are genetically diverse. To date, there is no valuable data about prevalence of norovirus infection and the dominant genogroup/genotype among Iranian population. The objective of this study was to determine the frequency of norovirus infection in Iranian patients with gastroenteritis referred to three hospitals of Tehran and to specify the dominant genogroup/genotype of this virus among our study population. A total of 293 patients with acute gastroenteritis were included in the study. Detection of norovirus was performed using RT-PCR method and confirmed by direct sequencing with specific designed primers for capsid region of norovirus genome. Phylogenetic analysis was performed using the neighbor-joining method. Norovirus strains identified in our study were subsequently categorized according to previously defined genogroup/genotypes. Of these, norovirus GII was dominant genogroup. Sixty-five percent (17 of 26) of positive samples were determined as GII and 35% (9 of 26) were determined as GI, respectively, in 2008–2009. And among 8 sequenced strains of genogroup II the most frequent genotype was GII.3. The results of this study indicated that norovirus must be considered as one of the infectious causes of acute gastroenteritis among Iranian population. We also found that GII.3 is more prevalent in our study population. To the best of our knowledge there is limited data about the role of noroviruses in children and adults’ acute gastroenteritis among Iranian patients and this prevalence and genotyping report of norovirus infection could be remarkable for further studies.     

Relationship between musculoskeletal disorders and anthropometric indices among bus drivers in Zahedan city

Introduction. Most work-related musculoskeletal disorders (MSDs) are associated with improper postures and poorly designed workstations. This study is an attempt to examine the prevalence and severity of MSDs as well as anthropometric dimensions among city bus drivers. Methodology. This cross-sectional study was carried out on 60 male bus drivers. A body discomfort chart was used to evaluate MSDs. Spearman correlation was employed to examine the relationship between body size and the severity of discomfort. Results. Data analysis showed that discomfort reported in the lower back (33.3%), upper back (18.3%) and knee (15%) was severe and there was a direct and significant correlation between the body mass index and the severity of discomfort in the shoulder, arm and hip (p?p?Conclusion. The results of the study can be used to address ergonomic risk factors and reduce their associated disorders. The findings of the study can be used in training programs to educate drivers how to decrease the risk associated with work-related MSDs by adopting appropriate behavior strategies.     

Preparation and Properties of Starch/Nanosilicate Layer/Polycaprolactone Composites

Starch nanocomposites have been prepared using mineral clay. Montmorillonite, kaolin and a surface-modified montmorillonite by dimethyl (hydrogenated tallow alkyl) ammonium cation were used. Starch-g-PCL nanocomposites have been prepared with graft polymerization through in situ ring-opening polymerization of ε-caprolactone in the presence of starch, Sn(Oct)₂ (Tin(II) 2-ethyl hexanoate) as an initiator/catalyst and silicate layers. In fact, the related composites were prepared in solution method, bulk polymerization and in situ polymerization methods with introducing the mineral clay. The effect of kind of clay on d-spacing of silicate layers was investigated and the obtained nanocomposites were analyzed using X-ray diffraction. The obtained compounds were characterized by Fourier transform infrared (FT-IR). Morphology of the prepared nanocomposites was investigated using scanning electron microscopy and DSC enhanced the study of thermal behaviour of the prepared composite compounds.