Drivers for innovation in waste-to-energy technology.

This paper summarizes developments made in the field of waste-to-energy technology between the 1980s and the present. In the USA, many waste-to-energy systems were developed in the 1980s and early 1990s. These plants generated power relatively efficiently (typically 23%) in 60 bar/ 443 degrees C boilers. Unfortunately, the development came to a stop when the US Supreme Court rejected the practice of waste flow control in 1994. Consequently, waste was directed to mega-landfills, associated with very negative environmental impacts. However, given landfill taxes and increased fuel prices, new waste-to-energy projects have recently been developed. Attractive premiums for renewable power production from municipal waste have been introduced in several European countries. This triggered important innovations in the field of improved energy recovery. Examples of modern waste-to-energy plants are Brescia and Amsterdam with net efficiencies of 24 and 30%, respectively. Incineration is traditionally preferred in Japan due to space constraints. New legislation promoted ash melting or gasification to obtain improved ash quality. However, these processes reduce the efficiency in terms of energy, cost and availability. A new oxygen-enriched waste-to-energy system is under development in order to better achieve the required inert ash quality.     

Ternäre Verbindungen von Cadmiumhalogeniden mit Arsen und Antimon

The Science of Nature -     

Renatal diagnosis of mosaic tetrasomy 12p/trisomy 12p by fluorescent in situ hybridization in amniotic fluid cells: A case report of pallister–killian syndrome

A prenatally detected case of a rare mosaic tetrasomy 12p/trisomy 12p is reported, presenting as the well-known accessory isochromosome 12p and a supernumerary single 12p marker in 17/24 and 6/24 clones of cultured amniotic fluid cells, respectively. The chromosomal nature of both marker chromosomes was investigated in cultured amniotic fluid cells by fluorescent in situ hybridization with various probes: the 12-centromeric probes pa12H8 and D12Z3, a whole chromosome 12 paint, and the chromosome 12p-specific paint M28. DNA analysis revealed a maternal origin of the extra 12p material. After counselling, the parents requested termination of pregnancy. Inspection and autopsy of the fetus revealed many of the dysmorphisms and internal structural abnormalities of the Pallister–Killian syndrome.     

Wetland loss and substitution by the Section 404 permit program in southern California,USA

To test the effectiveness of the 404 permit program in preventing a net loss of wetland resources, 75 Section 404 projects permitted in the years 1987–1989 and located in a portion of southern California were evaluated. From this group of projects, 80.47 ha of wetlands were affected by Section 404 permits and the Army Corps of Engineers required 111.62 ha of wetland mitigation. To verify the successful completion of each mitigation project, all 75 project sites were visited and evaluated based on the amount of dead vegetation, growth and coverage, and the number of invasive species. Based on the field verification results, the actual amount of completed mitigation area was 77.33 ha, resulting in a net loss of 3.14 ha of wetland resources in the years 1987–1989. By comparing the types of wetlands lost to the types of wetlands mitigated, it is apparent that, in particular, freshwater wetlands are experiencing a disproportionately greater loss of area and that riparian woodland wetlands are most often used in mitigation efforts. The net result of these accumulated actions is an overall substitution of wetland types throughout the region. Results also indicate that, typically, large-scale mitigation projects are more successful compared to smaller projects and that successful compliance efforts are not evenly distributed throughout the region. We recommend that better monitoring, mitigation in-kind, mitigation banking, and planning on a regional or watershed scale could greatly improve the effectiveness of the Section 404 permitting program.     

Synthesis of poly(hydroxyalkanoate) from hydrolyzed linseed oil

Pseudomonas putida was grown on a mixture of long-chain fatty acids obtained by hydrolysis of linseed oil. A poly(3-hydroxyalkanoate) containing 51.2% of unsaturated monomers was obtained. A considerable percentage (13.6%) was constituted by C₁₄ and C₁₆ monomers containing three double-bonds in the side chains. The polymer showed a high tendency to crosslink when it was kept in presence of air. In the crosslinked polymer no polyunsaturated monomers could be detected.     

Impact of mineral components and selected trace metals on ambient PM10 concentrations

PM10 levels of the mineral components Si, Al, Fe, Ca, Mg and some trace metals were measured at three different sites in the urban area of Vienna (Austria). Observed trace metal concentrations varied between less than 0.1 ng m^?3 (Cd) and approximately 200 ng m^?3 (Zn), mineral components showed enhanced concentrations ranging from 0.01 μg m^?3 (Ca) to 16.3 μg m^?3 (Si). The contribution of the respective mineral oxides to PM10 mass concentrations accounted on average for 26.4 ± 16% (n = 1090) of the PM10 mass, with enhanced rates in spring and autumn (monthly averages of up to 40%) and decreased contributions in the cold season (monthly averages below 10%). The atmospheric occurrence of Al, Ti and Sr could be assigned to crustal sources, whereas for the elements Ba, Ca, Fe, Mg, Mn and V an increased contribution of non-crustal origin was observed. PM10 levels of As, Cd, Co, Cr, Cu, Ni, Pb, Sb, Sn and Zn were predominantly derived from man-made emissions. Intersite comparison indicated that urban PM10 mass concentrations and PM10 levels of As, Pb and Zn were predominantly influenced from the transport of aerosols from outside into the city, whereas for the elements Ba, Mg, Ca, Cu and Fe a distinctly increased impact of local emissions was observed. The contribution of these urban emissions to total PM10 concentrations was estimated by calculating the so-called “urban impact”, which was found to be 32.7 ± 18% (n = 392) in the case of PM10 mass concentrations. The investigated elements accounted on average for 31.3 ± 19% (n = 392) of the observed PM10 mass increase. The mean values for the “urban impacts” of individual elements varied between 25.5% (As) and 77.0% (Ba).     

Monitoring Australian Rangeland Sites Using Landscape Function Indicators and Ground- and Remote-Based Techniques

If the goal for managing rangelands is to achieve a balance between production and conservation, then monitoring is essential to detect change and apply corrective action. In some range-land areas of northern Australia, monitoring has detected a tilt in the production-conservation balance towards excessive production. How big is this imbalance? Can it shift back? Robust monitoring is needed to answer these questions. The aim is to know what to monitor, and where. For example, to detect changes caused by livestock on rangeland forage production and soil erosion, indicators linking grazing disturbances to landscape function are needed, that is, indicators that signal how well landscapes are capturing, concentrating, and utilizing scarce water, nutrient, and organic resources. Studies in Australia and the USA document that simple vegetation and soil patch attributes can be measured as indicators of the 'state of health' of landscape function. For example, field and remote sensing-based grazing studies in Australia document that landscapes with a high cover of perennial plant patches function effectively to capture runoff water and nutrients in sediments, whereas landscapes with a low cover of these patches do not — they are dysfunctional — as indicated by large patches of bare soil. Aerial videography is proving to be a robust technique for measuring indicators of landscape function such as small patches of vegetation and the extent of bare soil. These indicators typically have a sigmoidal response to grazing impacts. We illustrate that if these indicators are measured on monitoring sites established near the sigmoidal 'point of inflection’ then small changes in these indicators can be detected.