Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

Emissions of VOCs at Urban Petrol Retail Distribution Centres in India (Delhi and Mumbai)

Air pollution has assumed gigantic proportion killing almost half a million Asians every year. Urban pollution mainly comprises of emissions from buses, trucks, motorcycle other forms of motorized transport and its supporting activities. As Asia's cities continue to expand the number of vehicles have risen resulting in greater pollution. Fugitive emissions from retail distribution center in urban area constitute a major source. Petrol vapours escape during refueling adding pollutants like benzene, toluene, ethylbenzene and xylene to ambient air. This paper discusses a study on fugitive emissions of Volatile Organic Compounds (VOC) at some refueling station in two metropolitan cities of India, i.e., Mumbai and Delhi. Concentration of VOCs in ambient air at petrol retail distribution center is estimated by using TO-17 method. Concentration of benzene in ambient air in Delhi clearly shows the effect of intervention in use of petroleum and diesel fuel and shift to CNG. Chemical Mass Balance (CMB) model is used to estimate source contributions. At Delhi besides diesel combustion engines, refueling emissions are also major sources. At Mumbai evaporative emissions are found to contribute maximum to Total VOC (TVOC) concentration in ambient air.     

Design parameters for fixed bed reactors of activated carbon developed from fertilizer waste for the removal of some heavy metal ions

Activated carbon, developed from fertilizer waste, has been used for the removal of Hg²⁺, Cr⁶⁺, Pb²⁺, and Cu²⁺. Mass transfer kinetic approach has been successfully applied for the determination of various parameters necessary for designing a fixed-bed absorber. Parameters selected are the length of the (PAZ) primary adsorption zone (δ), total time involved for the establishment of primary adsorption zone (t_x), mass rate of flow to the absorber (F_m), time for primary adsorption zone to move down its length (t_δ), amount of adsorbate adsorbed in PAZ from breakpoint to exhaustion (M_s), fractional capacity (f), time of initial formation of PAZ (t_f) and per cent saturation of column at break point. Chemical regeneration has been achieved with 1 M HNO₃.     

Characterization of carbonaceous aerosols over Delhi in Ganga basin: seasonal variability and possible sources

The mass concentration of carbonaceous species, organic carbon (OC), and elemental carbon (EC) using a semicontinuous thermo-optical EC-OC analyzer, and black carbon (BC) using an Aethalometer were measured simultaneously at an urban mega city Delhi in Ganga basin from January 2011 to May 2012. The concentrations of OC, EC, and BC exhibit seasonal variability, and their concentrations were ～2 times higher during winter (OC 38.1?±?17.9 μg m^?3, EC 15.8?±?7.3 μg m^?3, and BC 10.1?±?5.3 μg m^?3) compared to those in summer (OC 14.1?±?4.3 μg m^?3, EC 7.5?±?1.5 μg m^?3, and BC 4.9?±?1.5 μg m^?3). A significant correlation between OC and EC (R?=?0.95, n?=?232) indicate their common emission sources with relatively lower OC/EC ratio (range 1.0–3.6, mean 2.2?±?0.5) suggests fossil fuel emission as a major source of carbonaceous aerosols over the station. On average, mass concentration of EC was found to be ～38 % higher than BC during the study period. The measured absorption coefficient (b_abs) was significantly correlated with EC, suggesting EC as a major absorbing species in ambient aerosols at Delhi. Furthermore, the estimated mass absorption efficiency (σ_abs) values are similar during winter (5.0?±?1.5 m² g^?1) and summer (4.8?±?2.8 m² g^?1). Significantly high aerosol loading of carbonaceous species emphasize an urgent need to focus on air quality management and proper impact assessment on health perspective in these regions.     

Effects of distillery waste on the performance of Cicer arietinum L

The impact of distillery effluent in various concentrations (1, 2.5, 5, 10, 25, 50, 75 and 100%) on the seed germination, Speed of Germination Index, growth behaviour, leaf area, biomass, net primary productivity, pigment content, reproductive capacity, seed output, seed weight, seed density and the seed protein content of Cicer arietinum L. plants was investigated. The percentage and speed of germination of seeds were increasingly retarded with increase in effluent concentration and at 100% concentration there was no germination. The seedlings exhibited maximum shoot length at 5% concentration and maximum root length at 2.5% concentration. The values of root and shoot lengths, leaf area, biomass, net primary productivity, pigment content, reproductive capacity, seed output, seed weight, seed density and seed protein content in pot plants exhibited a gradual increase from the control up to 5% concentration and decreases at higher concentrations. The very high BOD load and the presence of excessive concentrations of soluble salts could be responsible for the toxicity of the effluent. The effluent at up to 5% concentration was, however, beneficial for the overall growth parameters studied and can thus be used as a liquid fertilizer.     

Sorption of the veterinary antimicrobials sulfadimethoxine and ormetoprim in soil

Currently, limited research on the fate of antimicrobials in the environment exists, once they are discharged in human and animal wastes. Sorption of two antimicrobials, sulfadimethoxine (SDM) and ormetoprim (OMP), was investigated in two soils and sand using a series of batch experiments. Because OMP and SDM are often administered in combination, their sorption was also investigated in combination as co-solutes. The rate of SDM and OMP sorption was rapid over the first few hours of the experiments, which then slowed considerably after 16 to 68 h. OMP sorption was enhanced at high concentrations when in combination with SDM, with linear sorption coefficients ranging from 1.3 to 58.3 L.kg(-1) in the single solute experiments and 4.96 to 89.7 L.kg(-1) in the co-solute experiments. Sorption of OMP as a single solute seems to provide a better fit with the Freundlich equation, which became more linear (n approached 1) when SDM was present. Overall, SDM sorbed less than OMP in the two soils and sand. SDM linear sorption coefficients ranged from 0.4 to 25.8 L.kg(-1) as a single solute and 2.5 to 22.1 L.kg(-1) as a co-solute. Sorption of SDM becomes more nonlinear (n < 1) when SDM is present in combination with OMP. Overall, sorption of both antimicrobials increased in the selected soils and sand as the organic matter, clay content, and cation exchange capacity increased. These experiments indicate relatively low sorption of SDM and OMP in natural soils, making them a potential threat to surface and ground water.     

Role of blue green algae biofertilizer in ameliorating the nitrogen demand and fly-ash stress to the growth and yield of rice (Oryza sativa L.) plants

Rice is a major food crop throughout the world; however, accumulation of toxic metals and metalloids in grains in contaminated environments is a matter of growing concern. Field experiments were conducted to analyze the growth performance, elemental composition (Fe, Si, Zn, Mn, Cu, Ni, Cd and As) and yield of the rice plants (Oryza sativa L. cv. Saryu-52) grown under different doses of fly-ash (FA; applied @ 10 and 100 tha(-1) denoted as FA(10) and FA(100), respectively) mixed with garden soil (GS) in combination with nitrogen fertilizer (NF; applied @ 90 and 120 kg ha(-1) denoted as NF(90) and NF(120), respectively) and blue green algae biofertilizer (BGA; applied @ 12.5 kg ha(-1) denoted as BGA(12.5)). Significant enhancement of growth was observed in the plants growing on amended soils as compared to GS and best response was obtained in amendment of FA(10)+NF(90)+BGA(12.5). Accumulation of Si, Fe, Zn and Mn was higher than Cu, Cd, Ni and As. Arsenic accumulation was detected only in FA(100) and its amendments. Inoculation of BGA(12.5) caused slight reduction in Cd, Ni and As content of plants as compared to NF(120) amendment. The high levels of stress inducible non-protein thiols (NP-SH) and cysteine in FA(100) were decreased by application of NF and BGA indicating stress amelioration. Study suggests integrated use of FA, BGA and NF for improved growth, yield and mineral composition of the rice plants besides reducing the high demand of nitrogen fertilizers.     

Indoor Air Quality of Public Places in Mumbai, India in Terms of Volatile Organic Compounds

Indoor air quality at nine locations viz. food courts, restaurant, bar, conference room, office and theater, which can be classified as public places have been monitored for Volatile Organic Compounds (VOCs) content. Forty VOCs have been identified and one fourth of these are classified as Hazardous Air Pollutants. Levels of most VOCs are observed to be below the guideline values for public places and offices, as adopted by Hong Kong. Consumer goods are found to be predominant source of chlorinated VOCs in indoor air. Levels of benzene and carbon tetrachlorides were observed to be above the guideline values at all the locations. Effect of ozonisation on Total VOC concentrations have also been studied.     

Design and evaluation of an atomization-based cutting fluid spray system in turning of titanium alloy

Tool life has been a vital issue in machining titanium alloys. Recently, an atomization-based cutting fluid (ACF) application has been found to be an effective approach for cooling and lubrication in micromachining operations. In this study, an ACF spray system is developed for macro-scale turning of Ti–6Al–4V. The spray system is designed to minimize interaction between the fluid droplets, and the gas nozzle to control the divergence of the fluid droplets. Experiments are conducted to study the effect of five specific ACF spray parameters including fluid flow rate, spray distance, impingement angle, and type and pressure level of the droplet carrier gas on cutting forces, tool life, and chip characteristics. It has been observed that the combination of lower pressure (150 psi) air-mixed CO₂ with a higher flow rate (20 ml/min) and a larger spray distance (35 mm) produces a significantly longer tool life and broken chips. The results also reveal that the ACF spray system can extend tool life up to 40–50% over flood cooling.