Chemical states of arsenic contained in sewage sludge incineration ash and insolubilized material

Journal of Material Cycles and Waste Management - The chemical states of arsenic contained in 4 kinds of sewage sludge incineration ash and insolubilized materials are analyzed using a leaching...     

The effectiveness of the e-money incentive mechanism in promoting separation of recyclables at source in Malaysia

Journal of Material Cycles and Waste Management - A new concept of a reward system by two e-money-incentive systems aimed at improving separation at source toward reducing residual waste generation...     

Evaluation of a recycling process for printed circuit board by physical separation and heat treatment

Printed circuit boards (PCBs) from discarded personal computer (PC) and hard disk drive were crushed by explosion in water or mechanical comminution in order to disintegrate the attached parts. More parts were stripped from PCB of PC, composed of epoxy resin; than from PCB of household appliance, composed of phenol resin.In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 873–1073 K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment.As one of the mounted parts, the multi-layered ceramic capacitors (MLCCs), which contain nickel, were carbonized at 873 K. The magnetic separation is carried out at a lower magnetic field strength of 0.1 T and then at 0.8 T. In the +0.5 mm size fraction the nickel grade in magnetic product was increased from 0.16% to 6.7% and the nickel recovery is 74%.The other useful mounted parts are tantalum capacitors. The tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723–773 K in air atmosphere and screening of 0.5 mm. Silica was removed and 70% of tantalum grade was obtained after more than 823 K heating and separation.Next, the evaluation of Cu recycling in PCB is estimated. Energy consumption of new process increased and the treatment cost becomes 3 times higher comparing the conventional process, while the environmental burden of new process decreased comparing conventional process.The nickel recovery process in fine ground particles increased energy and energy cost comparing those of the conventional process. However, the environmental burden decreased than the conventional one.The process for recovering tantalum used more heat for the treatment and therefore the energy consumption increased by 50%, when comparing with conventional process. However, the market price for tantalum is very large; the profit for tantalum recovery is added. Also the environmental burden decreased by the recycling of tantalum recovery. Therefore, the tantalum recovery is very important step in the PCB recycling. If there is no tantalum, the consumed energy and treatment cost increase in the new process, though the environmental burden decreases.     

Capability development of local communities for project sustainability in afforestation/reforestation clean development mechanism

It has been recognized that the involvement of local community is essential to ensure the sustainability of A/R CDM (afforestation/reforestation clean development mechanism) project. This study verifies if the risks of non-permanence and leakage are addressed in a registered small scale A/R CDM project in Vietnam. Workshops, interviews, and a questionnaire survey of local villagers revealed that the project has caused a shortage of land for conventional activities such as grazing, fuel wood collection and shifting cultivation, and consequently posed the risks of project non-permanence and leakage. It is suggested that participation of all stakeholders in the community to the A/R CDM project beyond existing land tenure and adequate carbon benefit sharing according to the level of contribution to the project are required to reduce the risk of non permanence. To ensure the participation, the community should have capability such as consensus building and collective action. Leakage would be minimized if the community has alternative measures to the conventional activities before starting the project. We argue that it is necessary to first develop a community’s capabilities in the readiness phase of any A/R CDM project in order to reduce the risks for the project sustainability, and that new sources of funding are needed for this purpose.     

Ecological impacts of umbrella effects of radiation on the individual members

In order to study the interactions in a model aquatic microcosm, an individual-based computer simulation model was developed. The microcosm consists of Euglena gracilis as an autotroph algae, Tetrahymena thermophila as a heterotroph protozoa and Escherichia coli as a saprotroph bacteria. There exists a strong interaction between Tetrahymena and E. coli as the first is the predator of the second. Ecological toxicity tests were conducted to test the population level impacts of the biological effects of radiation and toxicants on the lethality and mobility factors that influence directly or indirectly growth and reproduction. Radiological effects on lethality of E. coli individuals were translated to the reduction of the equilibrium population of Tetrahymena. A synergistic effect at the community level was also observed by the simulation of a combined exposure of radiation and a toxicant which reduced the feeding efficiency of Tetrahymena.     

Impact of gamma irradiation on the transformation efficiency for extracellular plasmid DNA

Extracellular DNA is omnipresent in aquatic environments and is thought to be a genetic material for horizontal gene transformation between microorganisms. We studied the impact of gamma irradiation on the transformation efficiency (transformants number per ng of DNA per ml) of extracellular DNA. Plasmid pEGFP as a model extracellular DNA was irradiated by gamma rays. The transformation efficiency decreased with the increase in radiation dose. A total dose of 10Gy is normally not lethal for microorganisms but certainly affects the transformation efficiency of extracellular DNA. The decrease in the efficiency would be induced by strand breaks of extracellular DNA because the yield of both single-strand breaks (SSBs) and double-strand breaks (DSBs) increased with the increase in radiation dose. The relative transformation efficiency of SSBs and DSBs to that of covalently closed circles (CCCs) was 30.3% and 0.2%, respectively. This impact on natural transformation suggests an inability of microorganisms to acquire new characteristics which should be normally acquired.     

Challenging the current strategy of radiological protection of the environment: arguments for an ecosystem approach

The system of radiological protection of the environment that is currently under development is one contribution to the general need to adequately protect the environment against stress. Dominated by operational goals, it emphasizes conceptual and methodological approaches that are readily accessible today: reference organisms supported by individual-based traditional ecotoxicological data. Whilst there are immediate advantages to this approach (pragmatism, consistency with other approaches in use for man and biota), there are also clear limitations, especially in a longer run perspective, that need to be acknowledged and further considered. One can mention a few: uncertainties generated by the need for various extrapolations (from lower to higher levels of biological organisation, …), various features missed such as potential ecological impact through impairment of ecosystem processes, trans-generational impacts as mediated through genomic instability, indirect effects mediated through trophic interactions or disruption of ecological balances,… Such limitations have already been faced in other fields of environmental protection against other stressors, pushing a number of environment professionals to assign stronger emphasis on more systemic approaches. This review discusses the advantages and limitations of the current approach designed for the radiological protection of non-human biota in the broader context of environment protection as a whole, with especial reference to upcoming trends and evolutions. This leads in particular to advocating the need to boost scientific and methodological approaches featuring the ecosystem concept as a mean to access a unified goal of protection: preserving life sustainability through protection of ecosystem structure and functioning.     

Environmental and economic life cycle assessment for sewage sludge treatment processes in Japan

Life cycle assessment for sewage sludge treatment was carried out by estimating the environmental and economic impacts of the six alternative scenarios most often used in Japan: dewatering, composting, drying, incineration, incinerated ash melting and dewatered sludge melting, each with or without digestion. Three end-of-life treatments were also studied: landfilling, agricultural application and building material application. The results demonstrate that sewage sludge digestion can reduce the environmental load and cost through reduced dry matter volume. The global warming potential (GWP) generated from incineration and melting processes can be significantly reduced through the reuse of waste heat for electricity and/or heat generation. Equipment production in scenarios except dewatering has an important effect on GWP, whereas the contribution of construction is negligible. In addition, the results show that the dewatering scenario has the highest impact on land use and cost, the drying scenario has the highest impact on GWP and acidification, and the incinerated ash melting scenario has the highest impact on human toxicity due to re-emissions of heavy metals from incinerated ash in the melting unit process. On the contrary, the dewatering, composting and incineration scenarios generate the lowest impact on human toxicity, land use and acidification, respectively, and the incinerated ash melting scenario has the lowest impact on GWP and cost. Heavy metals released from atmospheric effluents generated the highest human toxicity impact, with the effect of dioxin emissions being significantly lower. This study proved that the dewatered sludge melting scenario is an environmentally optimal and economically affordable method.