金属加工过程中应力状态的分析方法

分析简单地拉伸、压缩和扭转的情况时,应力状态能容易地被确定.但是,实际上在金属加工过程中材料是承受复杂的应力状态,在模具——工件接触面上增加有摩擦力.而且,这些应力和摩擦力一般地沿着接触面变化.准确的计算或预测载荷、力、应力和温度,不但对设计适宜的设备是重要的,而且对研究工艺期间材料的变化过程也是重要的.本文将讨论材料变形过程中所运用的主要分析方法及其优缺点.     

2018年春节期间京津冀地区污染过程分析

为了解2018年春节期间京津冀地区空气污染情况,利用近地面污染物浓度数据、激光雷达组网观测数据,结合WRF气象要素、颗粒物输送通量和HYSPLIT气团轨迹综合分析污染过程.结果表明,春节期间出现3次污染过程.春节前一次污染过程,各站点PM_2.5浓度均未超过200μg/m³;除夕夜,廊坊站点PM_2.5峰值浓度达到504μg/m³,是清洁天气的26倍;年初二~初五,各站点PM_2.5始终高于120μg/m³,且污染主要聚集在500m高度以下,北京地区存在高空传输,800m处最大输送通量达939μg/（m³·s）,此次重污染过程为一次典型的区域累积和传输过程.京津冀地区处于严格管控状态时,燃放烟花爆竹期间PM_2.5峰值浓度可达无燃放时PM_2.5峰值的3.2倍.为防止春节期间重污染现象的发生,需对静稳天气下燃放烟花炮竹采取预防对策.     

A study on the interactions among several plant secondary compounds and aphids

The research, focused on the specific interactions among seven plant secondary compounds and aphids, was carried out and the preliminary results showed: (1) "T-typed tube method" was regarded as the best method compared with others designed to observe the interactions. (2) Cabbage aphid was able to be attracted by laurolene while it was not susceptible to α-pinene, β-pinene and diamylene. (3) Gossypol, a major secondary substance in cotton, was able to be implicated as feeding attractant to cotton aphid. (4) Rutin might be implicated repellent to cotton aphid.     

红壤中结合态磷在酸化条件下的变化及其相互关系

以浙江沿海地区的红壤为研究对象，通过浸滤过程，研究了在酸化条件下，红壤中可溶笥结合态磷的变化和它们之间的相关关系，结果显示，红壤中可溶性Fe-P比Ca－P、Al－P对酸度的变化更为敏感；当红壤中可溶性磷的原始含量较高时，随酸度的增强从固相中释出的趋势更明显；在酸化过程中、红壤中不同可溶性结合态磷之间呈现出不同的相关关系，这归因子它们对酸化敏感性的差异。     

Occurrence and congeners specific of poiychlorinated biphenyls in agricultural soils from Southern Jiangsu, China

A total of 198 agricultural soil samples were collected from Zhangjiagang and Changshu in Southern Jiangsu for analysis of 13 polychlorinated biphenyls (PCBs) in order to assess the levels of pollution, sources, area distribution, and potential risk for the environment. All methods were rigorously tested and an adequate quality control was ensured. Only one site had no PCBs residues, and the highest total PCBs concentration in the surface soils was 32.83 ng/g. The average concentration in all the soil samples was 4.13 ng/g, signaling low-level pollution. Tetra-, penta-, and hexa-chlorinated biphenyls were dominant species in soil samples, accounting for more than 75% ofΣPCBs in the soil samples. PCB118 was the most abundant congener in all the samples. The PCB118 was about 20% ofΣPCBs. The soil organic matter content showed only a weak correlation with the levels of all PCB congeners, in which a better correlation was noted for the more volatile lighter PCB congeners than for the heavier homologues. To a certain extent, the sources and land use seemed to influence the levels of PCBs.     

ASM1中废水和污泥组分浓度的测定方法研究

对呼吸计量法应用于校准ASM1作了简明的阐述。在呼吸速率与模型组分关系的基础上,介绍了ASM1中废水与污泥各组分浓度的测定方法,并指出模型组分细化的意义。     

楔横轧轴肩的成形曲面的设计

此文分析在二辊楔横轧中轧制各类轴肩的过程。在假想工件轴端固定的图上确定楔侧面截面轮廓形状,再通过叠加轴向刚性移动量确定各截面实际位置,比较直观简便地设计出轧制轴肩的辊面上的成形曲面。最后归纳了设计步骤。     

数值模拟的可视化及其实现技术

此文介绍了一个用于数值模拟过程的二维图形界面,它由两大部分组成:“MANU”实现计算结果的手工操作显示及编辑,“AUTO”用于数值计算过程的自动跟踪.文中详细介绍了系统的设计方法、结构、工作原理和主要功能.     

梯齿形桥梁伸缩缝U形弯曲件的成形技术

此文介绍一种新型桥梁伸缩缝关键零件U形弯曲件的成形技术.通过对该零件的变形分析和采用合理的工艺措施,使得这一成形难度较大的弯曲件一次压制获得成功.     

45钢工件在易裂尺寸范围内的超细化热处理

此文主要研究了易裂尺寸范围内的45钢工件的超细化热处理。结果表明:45钢工件在易裂尺寸(5mm～11mm)范围内进行循环淬火时,淬火介质直接影响45钢工件的超细化热处理质量,易裂尺寸范围内的45钢工件,采用肥皂水在830℃循环淬火四次加680℃反复回火后,其超细化热处理效果最佳。