论我国磷业发展战略

我国磷矿资源丰富,但长期以来缺乏磷业发展战略部署,磷矿山建设缓慢,磷肥供应不足,造成氮、磷、钾施肥比例失调,全国有2/3的耕地缺磷,其中半数严重缺磷,农业上出现了“报酬递减”现象。本文在分析我国磷业发展概况的基础上进行了磷矿与磷肥需求预测,根据我国农业及磷矿资源分布与有关开发建设条件等,提出了我国磷业发展战略与宏观生产布局,论证了发展磷业应立足国内、以国民经济总体部署为准则、建立4个大型综合性磷业基地、以资源型布点为主,辅以混合型、临海型和消费型布点等磷业发展战略中的重大问题,并提出了发展我国TS形双结构磷业网络的思想。     

XAFS study of starch-stabilized magnetite nanoparticles and surface speciation of arsenate

It has been shown that starch can effectively stabilize nanoscale magnetite particles, and starch-stabilized magnetite nanoparticles (SMNP) are promising for in situ remediation of arsenic-contaminated soils. However, a molecular level understanding has been lacking. Here, we carried out XAFS studies to bridge this knowledge gap. Fe K-edge XAFS spectra indicated that the Fe-O and Fe-Fe coordination numbers of SMNP were lower than those for bare magnetite particles, and these coordination numbers decreased with increasing starch concentration. The decrease in the average coordination number at elevated stabilizer concentration was attributed to the increase in the surface-to-volume ratio. Arsenic K-edge XAFS spectra indicated that adsorbed arsenate on SMNP consisted primarily of binuclear bidentate (BB) complexes and monodentate mononuclear (MM) complexes. More BB complexes (energetically more favorable) were observed at higher starch concentrations, indicating that SMNP not only offered greater adsorption surface area, but also stronger adsorption affinity toward arsenate.     

运行参数对水蚯蚓生物吸持六价铬性能影响研究

水蚯蚓能通过摄食剩余污泥而使污泥减量,但剩余污泥中常含有各种重金属污染物.本文以颤蚓科蠕虫(Tubificidae)为研究对象,以六价铬为典型重金属污染物,考察运行工艺参数:初始铬浓度、p H、水蚯蚓投加量和温度对水蚯蚓吸持六价铬的影响.实验结果表明,在研究浓度范围内(0.1~8.0 mg·L-1),水蚯蚓对六价铬的吸持速率随铬浓度的增大而加快,单位质量吸持量从14.4 mg·kg-1(以干重计,下同)增加到312.7 mg·kg-1,但六价铬的吸持率却随Cr6+初始浓度的增加而降低;p H从6.0增加到8.0,水蚯蚓对六价铬的吸持速率随p H的上升而提高,吸持率和单位质量吸持量先明显增强,p H达到7.5后逐渐趋于平衡,即吸持最佳p H为7.5;水蚯蚓投加量从1.0 g(以湿重计,下同)增加到5.0 g时,吸持速率及吸持率均上升,但单位质量吸持量却随着水蚯蚓投加量的增加而减少;当温度在10~20℃范围内时,水蚯蚓对六价铬的吸持速率相对较慢,到25℃时,吸持速率明显加快,吸持率和单位质量水蚯蚓的吸持量的变化趋势与吸持速率的变化相一致,但当温度达到30℃,水蚯蚓会大量死亡,综合考虑,处理系统最佳温度宜控制在25℃.     

Methyl Tertiary Hexyl Ether and Methyl Tertiary Octyl Ether as Gasoline Oxygenates: Assessing Risks from Atmospheric Dispersion and Deposition

Abstract

Methyl tertiary hexyl ether (MtHxE) and methyl tertiary octyl ether (MtOcE) are currently being developed as replacement oxygenates for methyl tertiary butyl ether (MtBE) in gasoline. As was the case with MtBE, the introduction of these ethers into fuel supplies guarantees their introduction into the environment as well. In this study, a screening-level risk assessment was performed by comparing predicted environmental concentrations (PEC) of these ethers to concentrations that might cause adverse effects to humans or ecosystems. A simple box model that has successfully estimated urban air concentrations of MtBE was adapted to predict atmospheric concentrations of MtHxE and MtOcE. Expected atmospheric concentrations of these ethers were also estimated using the European Union System for the Evaluation of Substances (EUSES) multimedia fate model, which simultaneously calculates PECs in the various environmental compartments of air, water, soil, and sediment. Because little or no data are available on the physicochemical, environmental, and toxicological properties of MtHxE and MtOcE, estimation methods were used in conjunction with EUSES to predict both the PECs and the concentrations at which these ethers might pose a threat. The results suggest that these ethers would contaminate the air of a moderately sized U.S. city (Boston, MA) at levels similar to those found previously for MtBE. The risk assessment module in EUSES predicted risk characterization ratios of 10^?3 and 10^?2 for MtHxE and MtOcE, respectively, in Boston, and 10^?2 and 10^?1 in very large urban centers, suggesting that these ethers pose only a minimal threat to ecosystems at the anticipated environmental concentrations. The assessment also indicates that these compounds are possible human carcinogens and that they may be present in urban air at concentrations that pose an unacceptable cancer risk. Therefore, testing of the toxicological properties of these compounds is recommended before they replace MtBE in gasoline.     

Catalytic activity of noble metal nanoparticles toward hydrodechlorination: influence of catalyst electronic structure and nature of adsorption

In this study, stabilized Pd, Pt and Au nanoparticles were successfully prepared in aqueous phase using sodium carboxymethyl cellulose (CMC) as a capping agent. These metal nanoparticles were then tested for catalytic hydrodechlorination toward two classes of organochlorinated compounds (vinyl polychlorides including trichloroethylene (TCE), tetrachloroethylene (PCE), and alkyl polychlorides including 1,1,1-trichloroethane (1,1,1-TCA), and 1,1,1,2-tetrachloroethane (1,1,1,2-TeCA)) to determine the rate-limiting steps and to explore the reaction mechanisms. The surface area normalized reaction rate constant, k_SA, showed a systematic dependence on the electronic structure (the density of states at the Fermi level) of the metals, suggesting that adsorption of organochlorinated reactants on the metal catalyst surfaces is the rate-limiting step for catalytic hydrodechlorination. Hydrodechlorination rates of 1,1,1-TCA and 1,1,1,2-TeCA agreed with the bond strength of the first (weakest) dissociated C-Cl bond, suggesting that C-Cl bond cleavage, which is the first step for dissociative adsorption of the alkyl polychlorides, controlled the catalytic hydrodechlorination rate. However, hydrodechlorination rates of TCE and PCE correlated with the adsorption energies of their molecular (non-dissociative) adsorption on the noble metals rather than with the first C-Cl bond strength, suggesting that molecular adsorption governs the reaction rate for hydrodechlorination of the vinyl polychlorides.     

Methyl tertiary hexyl ether and methyl tertiary octyl ether as gasoline oxygenates: assessing risks from atmospheric dispersion and deposition

Methyl tertiary hexyl ether (MtHxE) and methyl tertiary octyl ether (MtOcE) are currently being developed as replacement oxygenates for methyl tertiary butyl ether (MtBE) in gasoline. As was the case with MtBE, the introduction of these ethers into fuel supplies guarantees their introduction into the environment as well. In this study, a screening-level risk assessment was performed by comparing predicted environmental concentrations (PEC) of these ethers to concentrations that might cause adverse effects to humans or ecosystems. A simple box model that has successfully estimated urban air concentrations of MtBE was adapted to predict atmospheric concentrations of MtHxE and MtOcE. Expected atmospheric concentrations of these ethers were also estimated using the European Union System for the Evaluation of Substances (EUSES) multimedia fate model, which simultaneously calculates PECs in the various environmental compartments of air, water, soil, and sediment. Because little or no data are available on the physicochemical, environmental, and toxicological properties of MtHxE and MtOcE, estimation methods were used in conjunction with EUSES to predict both the PECs and the concentrations at which these ethers might pose a threat. The results suggest that these ethers would contaminate the air of a moderately sized U.S. city (Boston, MA) at levels similar to those found previously for MtBE. The risk assessment module in EUSES predicted risk characterization ratios of 10(-3) and 10(-2) for MtHxE and MtOcE, respectively, in Boston, and 10(-2) and 10(-1) in very large urban centers, suggesting that these ethers pose only a minimal threat to ecosystems at the anticipated environmental concentrations. The assessment also indicates that these compounds are possible human carcinogens and that they may be present in urban air at concentrations that pose an unacceptable cancer risk. Therefore, testing of the toxicological properties of these compounds is recommended before they replace MtBE in gasoline.     

Destruction of lindane and atrazine using stabilized iron nanoparticles under aerobic and anaerobic conditions: effects of catalyst and stabilizer

Highly stable Fe-Pd bimetallic nanoparticles were prepared with 0.2% (w/w) of sodium carboxylmethylcellulose (CMC) as a stabilizer. The effectiveness of the stabilized Fe-Pd nanoparticles was studied for degradation of two chlorinated pesticides (lindane and atrazine) under aerobic and anaerobic conditions. Batch kinetic tests showed that under anaerobic condition the nanoparticles can serve as strong electron donors and completely reduce 1 mgl(-1) of lindane at an iron dose of 0.5 gl(-1) or 1mg l(-1) of atrazine with 0.05 gl(-1) iron with a trace amount (0.05-0.8% of Fe) of Pd as a catalyst. In contrast, under aerobic condition, the nanoparticles can facilitate Fenton-like reactions, which lead to oxidation of 65% of lindane under otherwise identical conditions. Under aerobic condition, the presence of CMC reduced the level of hydroxyl radicals generated from the nanoparticels by nearly 50%, and thus, inhibited the oxidation of the contaminants. While the particle stabilization greatly enhanced the anaerobic degradation, it did not appear to be beneficial under aerobic condition. The degradation rate was progressively enhanced as the Pd content increased from 0.05% to 0.8% of Fe, and the catalytic effect of Pd was more significant under anaerobic condition. Under anaerobic condition, lindane is degraded via dihaloelimination and dehydrohalogenation, whereas atrazine is by reductive dechlorination followed by subsequent reductive dealkylation. Under aerobic condition, reactive oxygen species and hydroxyl radicals from the iron nanoparticles are responsible for oxidizing the pesticides. Lindane is oxidized via dechlorination/dehydrohalogenation, whereas atrazine is destroyed through dealkylation of the alkylamino side chain.     

In situ immobilization of Cu(II) in soils using a new class of iron phosphate nanoparticles

This study tested the feasibility of using a new class of iron phosphate (vivianite) nanoparticles synthesized using sodium carboxymethyl cellulose (NaCMC) as a stabilizer for in situ immobilization of Cu(II) in soils. Transmission electron microscopy measurements demonstrated that the particle size was about 8.4+/-2.9 nm. Batch tests showed that nano-sized vivianite particles can effectively reduce the leachability and in vitro bioaccessibility of Cu(II) in three representative soils (calcareous, neutral, and acidic) at the low doses of 0.61 and 3.01 mg PO(4) g(-1) soil. The Cu leachability was evaluated by the toxicity characteristic leaching procedure and in vitro bioaccessibility was evaluated by the physiological based extraction test. In the case of soil amendment with nanoparticles in 3.01 mg PO(4) g(-1) soil, Cu leachability reduced 63-87% and Cu concentrations in TCLP extract decreased from 1.74-13.33 mg l(-1) to 0.23-2.55 mg l(-1) after those soils were amended for 56 d. Meanwhile, the bioaccessibility of Cu was reduced by 54-69%. Sequential extraction procedures showed the significant decrease of water soluble/exchangeable Cu(II) and carbonate bound fractions and concomitant increase of Cu residual fraction after the soils were amended with the nanoparticles, suggesting that the formation of copper phosphate minerals through precipitation and adsorption was probably responsible for the decrease of Cu availability in soils. Visual MINTEQ modeling further revealed that Cu(3)(PO(4))(2) and Cu(5)(PO(4))(3)OH were formed in the vivianite-solid Cu(II) system, resulting in the decreased solubility of the Cu(II) in the acidic pH range.     

Remediation of soil and groundwater contaminated with organic chemicals using stabilized nanoparticles: Lessons from the past two decades

▪ Overviewed evolution and environmental applications of stabilized nanoparticles. ▪ Reviewed theories on particle stabilization for enhanced reactivity/deliverability. ▪ Examined various in situ remediation technologies based on stabilized nanoparticles. ▪ Summarized knowledge on transport of stabilized nanoparticles in porous media. ▪ Identified key knowledge gaps and future research needs on stabilized nanoparticles. Due to improved soil deliverability and high reactivity, stabilized nanoparticles have been studied for nearly two decades for in situ remediation of soil and groundwater contaminated with organic pollutants. While large amounts of bench- and field-scale experimental data have demonstrated the potential of the innovative technology, extensive research results have also unveiled various merits and constraints associated different soil characteristics, types of nanoparticles and particle stabilization techniques. Overall, this work aims to critically overview the fundamental principles on particle stabilization, and the evolution and some recent developments of stabilized nanoparticles for degradation of organic contaminants in soil and groundwater. The specific objectives are to: 1) overview fundamental mechanisms in nanoparticle stabilization; 2) summarize key applications of stabilized nanoparticles for in situ remediation of soil and groundwater contaminated by legacy and emerging organic chemicals; 3) update the latest knowledge on the transport and fate of stabilized nanoparticles; 4) examine the merits and constraints of stabilized nanoparticles in environmental remediation applications; and 5) identify the knowledge gaps and future research needs pertaining to stabilized nanoparticles for remediation of contaminated soil and groundwater. Per instructions of this invited special issue, this review is focused on contributions from our group (one of the pioneers in the subject field), which, however, is supplemented by important relevant works by others. The knowledge gained is expected to further advance the science and technology in the environmental applications of stabilized nanoparticles.