最优环境税:庇古法则与税制协调

从经济学的角度对国外关于最优环境税的经典理论——庇古法则及近十年来研究的前沿内容——一般均衡模型等作出阐释，并在外部性理论的基础上通过一个一般均衡模型考察环境税的效率特性和在次优情形下最优环境税的决定因素。随后是对我国开征环境税的几点思考：环境税的课征范围应暂定为排放各种废水、废气（烟尘）和固体废弃物的行为。环境税税率的确定可以采用“反复迭代”的方法，即“环境效益优先，兼顾税收协调和收入分配等效应。”其他相关问题的处理，如环境税和其它政策手段的配合使用，环境税税收的使用等。     

焚烧飞灰重金属含量及浸出长期变化规律研究

通过对24个飞灰样品的重金属全量消解和高精度X射线荧光光谱法（HDXRF）快速检测结果进行线性回归分析,发现HDXRF法可较准确测定飞灰中Cu、Pb、Zn、Ni和Cd含量（线性回归决定系数R²³0.90）.采用HDXRF法对某焚烧厂飞灰重金属含量6个月快速检测及浸出毒性测定数据统计分析发现：飞灰重金属月均含量较稳定（变异系数CV<0.14）但日均含量波动较大（CV>2.54）;飞灰中Pb、Cu和Zn含量呈正相关（相关系数r>0.78）;金属浸出浓度受浸出液终点pH值影响显著,超标频率依次为Pb（68.9%）、Cd（66.1%）、Ni（24.0%）、Cu（14.2%）和Zn（1.6%）.短期飞灰金属含量和浸出毒性数据受焚烧工况,烟气处理工况和垃圾组分等多种因素共同影响,不具有代表性.为评估垃圾分类源头削减重金属效果,建议采用快速检测方法对焚烧飞灰重金属含量进行长期监测.     

MnCeOx/沸石催化剂对工业典型VOCs的催化性能

以沸石为载体制备了锰铈复合氧化物催化剂（记为:MnCeO_x/沸石催化剂）,探究了催化剂对工业典型VOCs的二元催化性能,并对催化剂进行BET、XRD及SEM表征。结果表明:Ce的加入,促进了Mn的分散,提高了MnCeO_x/沸石催化剂的活性;当n（Mn）∶n（Ce）为1∶1,负载率为20%,焙烧温度为500℃时,催化剂的活性最高,其对甲苯的起燃温度（T₅₀）和完全燃烧温度（T₉₀）分别为155,255℃;单组分实验中,催化剂对3种有机物均表现出较高活性,转化率达到90%时的反应温度均在275℃以下,其活性顺序为乙酸乙酯>甲苯>丙酮,主要受反应活化能大小及分子极性的影响;二元催化实验中,由于竞争吸附的影响,3种物质的T₅₀和T₉₀较单组分均分别提高了8~13,14~38℃。     

基于Stacking的地面PM2.5浓度估算

为了解决地面PM_2.5监测网络在空间和时间覆盖受限的问题,提出了基于宽时空覆盖的卫星气溶胶光学厚度AOD,利用Stacking方法建立地面PM_2.5浓度估算模型,将AOD、PM_2.5和各气象参数以及与PM_2.5排放有关的数据进行训练,使用改进网格搜索对模型超参数进行优化,通过对多重共线性分析,建立基于Stacking的最优PM_2.5浓度估算模型。选取2016-01-01-2016-12-31的数据作为实验对象,结果表明:相比于随机森林、GBRT和XGBoost 3种模型,使用岭回归作为元学习器的Stacking模型性能更优,可见Stacking适用于大范围地理区域的大气污染监测。     

雨水管道沉积物中典型无机氮的干期粒径分布

以南京江北新区分流制雨水管道沉积物为研究对象,考察不同粒径沉积物中铵态氮（NH₃-N）和硝态氮（NO₃^--N）干期分布特征,分析其随干期长度的变化关系,并探讨沉积物理化性质及微生物菌群结构对NH₃-N和NO₃^--N干期分布的影响.结果表明：粒径≤0.075mm的沉积物中NH₃-N占比最高（交通区30.8%,商业区36.7%）;交通区粒径≤0.075mm的沉积物中NO₃^--N占比最高（33.0%）,而商业区粒径0.075~0.15mm沉积物中NO₃^--N占比最高（34.4%）;干期长度与交通区0.075~0.15mm粒径段的沉积物中NO₃^--N含量及商业区粒径≥0.3mm的沉积物中NH₃-N含量之间的相关性均最显著;雨水管道沉积物中NH₃-N和NO₃^--N的干期分布与O-H和N-H等官能团、表面极性和亲水性、微观形貌等有一定关联;交通区雨水管道沉积物中Gemmobacter等反硝化优势菌种（相对丰度总和为20.15%）对NO₃^--N干期分布影响更显著.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

水力空化-酸化调理增强污泥脱水性能分析

研究了水力空化-酸化调理作用于污泥脱水的机理。以污泥比阻（specific resistance to filtration,SRF）、污泥含水率和污泥毛细吸水时间（capillary sunction time,CST）作为主要的评价指标,测定污泥胞外聚合物（extracellular polymeric substances,EPS）中多糖、蛋白含量并进行了污泥酸化程度、污泥电子显微图像分析。结果表明:经水力空化-酸化调理污泥,污泥含水率和SRF分别从83.1%和5.12×1011 m/kg下降到69.8%和2.41×1011 m/kg,CST由50 s下降至20.8 s,各EPS组分含量下降明显,酸化作用通过影响污泥的溶解型胞外聚合物（S-EPS）和松散结合型胞外聚合物（LB-EPS）中的多糖及蛋白含量改变污泥的脱水性,pH=3时污泥脱水效果最好。综上所述,水力空化-酸化调理能大大增强污泥的脱水性能,在实际工程中具有很大的应用价值。     

不同制备温度下污泥生物炭对Cr(Ⅵ)的吸附特性

以城市剩余污泥为原料,于300,400,500,600 ℃温度条件下制备生物炭,通过单因素静态吸附实验探讨制备温度对生物炭吸附Cr（Ⅵ）的影响。结果表明:在500 ℃以内随着温度上升制备的生物炭对Cr（Ⅵ）的吸附量增加,制备温度高于500 ℃后变化不明显;扫描电镜（SEM）、比表面积（BET）、傅里叶红外光谱（FTIR）表征结果显示,热解温度对生物炭表面形貌和官能团组成有显著影响;等温模型及动力学拟合结果表明,生物炭吸附Cr（Ⅵ）为单分子层吸附、物理-化学复合吸附。热解温度对污泥制备生物炭吸附Cr（Ⅵ）的性能有显著影响,最佳制备温度为500 ℃,在此条件制备的生物炭对Cr（Ⅵ）的理论吸附量可达7.93 mg/g。