Life cycle energy impacts of automotive liftgate inner

This paper compares the life cycle energy use of a cast-aluminum, rear liftgate inner and a conventional, stamped steel liftgate inner used in a minivan. Using the best available aggregate life cycle inventory data and a simple spreadsheet-level analysis, energy comparisons were made at both the single-vehicle and vehicle-fleet levels. Since the product manufacture and use are distributed over long periods of time that, in a fleet, are not simple linear combinations of single product life cycles. Thus, it is all the products in use over a period of time, rather than a single product, that are more appropriate for the life cycle analysis. Using a set of consistent data, analyses also examine sensitivity to the level of analysis and the assumptions to determine the most favorable materials with respect to life cycle energy benefits.As expected, life cycle energy impacts of aluminum are lower than steel at a single-vehicle level – energy savings are determined to be 1.8 GJ/vehicle. Most energy savings occur at the vehicle operation phase due to improved fuel economy from lightweighting. The energy benefits are realized only very close to the average vehicle life of 14 years. With the incremental growth of the vehicle fleet, it takes longer – about 21 years – for aluminum to achieve life cycle equivalence with steel. The number of years aluminum needs to achieve equivalence with steel was found to be quite sensitive to aluminum manufacturing energy and fuel economy. As the steel industry races to compete with other materials for automotive lightweighting, a systems approach, instead of part-to-part comparison, is more appropriate in the determination of viability of aluminum substitution from an energy perspective.     

Phosphorus leaching in sandy outwash soils following potato-processing wastewater application

Land application of wastewater presents potential for ground water pollution if not properly managed. In situ breakthrough tests were conducted using potato (Solanum tuberosum L.)-processing wastewater and a Br tracer to characterize P leaching in seasonally frozen sandy outwash soils. In the first test, P and Br breakthrough were measured in a 7-m deep well following wastewater [2.94 mg L(-1) total P (TP); 280 mg L(-1) Br] application at the site that had 13.1 mg water-extractable P (WEP) kg(-1)and 94.4 mg Bray-1 P kg(-1). Bromide was detected in the well after approximately 0.4 pore volumes, but there was no P break-through after 7 pore volumes. In the second breakthrough test, wastewater containing 3.6 mg L(-1) TP and 259 mg L(-1) Br was applied on 1.5-m deep lysimeters at low (0.8 mg WEP kg(-1); 12.1 mg Bray-1 P kg(-1)) and high soil test P sites (104 mg WEP kg(-1); 585 mg Bray-1 P kg(-1)). Leachate TP concentration during the test remained constant (0.04 mg L(-1)) at the low P sites but increased from approximately 3.5 to 5.6 mg L(-1) at the high P sites. These results indicate no P leaching in low P soils, but leaching in high P soils, thus suggesting that most of the P leached at the high P sites was mainly due to desorption and dissolution of weakly adsorbed P from prior P applications. This was consistent with P transport simulations using the convective-dispersive equation. We conclude that P concentration in land-applied wastewater should be regulated based on soil test-P level plus wastewater P loading.     

Biomagnification of naturally-produced methoxylated polybrominated diphenyl ethers (MeO-PBDEs) in harbour seals and harbour porpoises from the Southern North Sea

Harbour seals and harbour porpoises are top predator species from the North Sea, have long life spans and hence, are known to accumulate high levels of anthropogenic contaminants. To gain knowledge about the behaviour of naturally-produced compounds in these marine mammals, the biomagnification of naturally-produced methoxylated polybrominated diphenyl ethers (MeO-PBDEs) was assessed. The biomagnification of MeO-PBDEs (2′-MeO-BDE 68 and 6-MeO-BDE 47) was lower in harbour seals (all biomagnification factors (BMFs) < 1) compared to the same age–gender groups of the harbour porpoises (all BMFs > 1). This may indicate a better metabolic breakdown of MeO-PBDEs in harbour seals, as was previously suggested for polybrominated diphenyl ethers (PBDEs). In both predators, 6-MeO-BDE 47 had the highest concentrations (range: 45–483 ng/g lw and 2–38 ng/g lw for harbour porpoises and seals, respectively) compared to 2′-MeO-BDE 68 (range: 2–28 ng/g lw and 1–6 ng/g lw for harbour porpoises and seals, respectively). In general, the highest concentrations were found in juveniles, suggesting an increased biotransformation capacity with age or the influence of dilution by growth for both species. Here we show that naturally-produced brominated organic compounds can biomagnify and accumulate in North Sea top predators, although to a lesser extent than anthropogenic lipophilic contaminants, such as polychlorinated biphenyls (PCBs) or PBDEs.     

Subsurface nutrient modelling using finite element model under Boro rice cropping system

Boro rice, an emerging low-risk crop variety of rice, cultivated using residual or stored water after Kharif season. To enhance the quality and production of rice, potassium (K) and phosphorus (P) are the common constituents of agricultural fertilizers. However, excess application of fertilizers causes leaching of nutrients and contaminates the groundwater system. Therefore, assessment and optimization of fertilizer dose are needed for better management of fertilizers. Towards this, the present study determines the path, persistence, and mobility of K and P under the Boro rice cropping system. The experimental site consisted of four plots having Boro rice with four different fertilizer doses of nitrogen (N), P, K viz. 100%, 75%, 50%, and 25% of the recommended dose. Disturbed soil samples were analysed for K and P from pre-sown land to tillering stage at 0–5, 5–10, 10–15, 15–30, 30–45, and 45–60 cm depths. Simultaneously, K and available P were also simulated in the subsurface soil layers through the HYDRUS-1D model. The statistical comparisons were made with RMSER, E, and PBIAS between the modelled values and laboratory-measured values. Although, the results showed that all the treatments considered had agreeable simulations for both K and P, the K simulations were found to be better as compared to P simulations except for 25% where P simulations outperformed K. The simulated concentration at all doses was found most appropriate when measured for the subsurface layers (up to 45 cm), while showed an underestimation in the bottom layers (45–60 cm) of soil.

     

Mercury emissions and partitioning from Indian coal-fired power plants

In India coal combustion is the single largest source of emission of mercury which is a wide-spread persistent global toxicant, travelling across international borders through air and water. As a party to the Minamata convention, India aims to monitor and reduce Hg emissions and stricter norms are introduced for mercury emissions from power plants (30 μg/Nm³for flue gas in stack).This paper presents the results obtained during the experimental studies performed on mercury emissions at four coal-fired and one lignite-fired power plants in India. The mercury concentration in the feed coal varied between 0.12–0.27 mg/Kg. In the mercury mass balance, significant proportion of feed coal mercury has been found to be associated with fly ash, whereas bottom ash contained very low mercury. 80%–90% of mercury was released to air through stack gas. However, for circulating fluidised bed boiler burning lignite, about 64.8% of feed mercury was found to get captured in the fly ash and only 32.4% was released to air. The mercury emission factor was found to lie in the range of 4.7–15.7 mg/GJ.     

Performance evaluation of dolomite production waste in development of sustainable concrete: hardened properties and ecological assessment

Journal of Material Cycles and Waste Management - Dolomite production waste is a by-product generated by dolomite mining, causing environmental pollution and other associated issues worldwide. In...     

Design parameters for fixed bed reactors of activated carbon developed from fertilizer waste for the removal of some heavy metal ions

Activated carbon, developed from fertilizer waste, has been used for the removal of Hg²⁺, Cr⁶⁺, Pb²⁺, and Cu²⁺. Mass transfer kinetic approach has been successfully applied for the determination of various parameters necessary for designing a fixed-bed absorber. Parameters selected are the length of the (PAZ) primary adsorption zone (δ), total time involved for the establishment of primary adsorption zone (t_x), mass rate of flow to the absorber (F_m), time for primary adsorption zone to move down its length (t_δ), amount of adsorbate adsorbed in PAZ from breakpoint to exhaustion (M_s), fractional capacity (f), time of initial formation of PAZ (t_f) and per cent saturation of column at break point. Chemical regeneration has been achieved with 1 M HNO₃.     

Removal of melanoidin present in distillery effluent as a major colorant: a review

Effluent originating from distilleries contain large amount of dark brown coloured wastewater called molasses spent wash (MSW). This MSW is the unwanted residual liquid waste to dispose because of low pH, high temperature, dark brown colour, high ash content, unpleasant odour and high percentage of organic and inorganic matter. Dark brown colour of MSW is due to the presence of melanoidin pigment. It reduces sunlight penetration in rivers and lakes which in turn decrease both photosynthetic activity and dissolved oxygen concentration affecting aquatic life. So the disposal of this effluent is one of the critical environmental issues. A number of treatment processes have been employed for the distillery waste management. This review paper present an overview of the pollution problems caused by melanoidin and the technologies employed globally for its removal.     

Measurement of the leaching behaviour of granular solid wastes

Leaching of granular solids can be described in terms of specific mass transfer functions of a simple mathematical form.

The parameters can be determined by column leaching experiments under well known flow conditions.

Initially available concentrations are obtained from batch experiments at high dilution. Total concentrations in the solids are determined independently to calculate the available fractions.

The determination of the flow pattern is done by radiotracer measurements. Leachates are analyzed by various analytical methods including AAS and INAA. Total concentrations in the solids are determined by INAA preferably.     

Effects of the level of dietary protein on the toxicity of hexachlorocyclohexane in rats

Male albino rats were fed for 28 days from weaning on diets containing 5% (group 1), 10% (group 2) and 21% (group 3, normal protein) protein as casein. At the end of dietary period, HCH was administered daily for 30 days to investigate the interaction between protein deficiency and pesticide toxicity. The results indicated that rats fed a lower protein diet and HCH had a higher mortality, lower rate of growth, increased liver weight and deposition of the pesticide in blood and tissues in larger amounts. Blood pressure (systolic and diastolic) was significantly increased and the heart rate showed tachycardia in low protein exposed animals. A significant increase of total lipids, cholesterol, triglycirides, free fatty acids in serum and tissues of animals exposed to low protein was observed. A close correlation existed between lipid accumulation and storage of HCH in tissues and dietary protein seemed to play an important role in detoxification.