Rotary Kiln Incineration II. Laboratory-Scale Desorption and Kiln-Simulator Studies—Solids

With landfill costs increasing and regulations on landfilling becoming more stringent, alternatives to conventional hazardous waste treatment strategies are becoming more desirable. Incineration Is presently a permanent, proven solution for the disposal of most organic contaminants, but also a costly one, especially in the case of solids which require some auxiliary fuel. The goal of this research is to develop an understanding of the phenomena associated with the evolution of contaminants from solids In the primary combustor of an Incineration system. A four-fold approach is being used. First, a bench-scale particle characterization reactor was developed to study the transport phenomena on a particle basis, where the controlling processes are mainly intraparticle. Second, a bed-characterization reactor was built to examine the controlling transport phenomena within a bed of particles, where the processes are primarily interparticle. The results of these studies can be applied to any primary combustor. A pilot-scale rotary kiln was developed to study the evolution of contaminants from solids within a realistic temperature and rotation environment. Finally, in situ measurements are being obtained from a full-scale rotary-kiln.

This paper describes results obtained in a study using a commercial sorbent contaminated with toluene. The data are from the particle-characterization reactor and the rotary-kiln simulator. The results show that the method of contamination and charge size do not have a large effect on desorption, while temperature and contaminant concentration are important parameters In the evolution of contaminants in a rotary kiln.     

Rotary Kiln Incineration III. An Indepth Study—Kiln Exit/Afterburner/Stack Train and Kiln Exit Pattern Factor Measurements During Liquid CCl4 Processing

Temperature and stable species concentration data are presented from various locations within a full-scale rotary kiln incinerator firing natural gas/carbon tetrachloride/air. The data are being collected as part of a cooperative program involving university, industry and government participation. The overall goal of the program is to develop a more sophisticated understanding of and a predictive capability for rotary kiln and afterburner performance as influenced by basic design and operational parameters. Non-uniformities in stable species and temperature exist for this particular kiln, at the kiln exit, under certain operating conditions. Flow perturbations from within the kiln were found to persist into the afterburner, but not into the stack. High destruction and removal efficiencies (DRE’s) were achieved under the operating conditions of these tests through adequate secondary combustion processing.     

Rotary Kiln Incineration IV. An Indepth Study— Kiln Exit,Transition and Afterburner Sampling During Liquid CCl4 Processing

Detailed temperature and stable species concentration data are presented from the kiln exit, transition section and afterburner of a full-scale incinerator facility firing natural gas/carbon tetrachloride/air. The data are collected as part of a cooperative program involving university, industry and government participation. The overall goal of the program is to develop an understanding and predictive capability for rotary kiln and afterburner performance as influenced by basic design and operational parameters. The data demonstrate that nonuniformities in stable species and temperature exist, under certain operating conditions, at the kiln exit in the vertical direction only. Measurements from the transition section indicate that non-uniformities may exist within this region under certain operating conditions. Flow perturbations from within the kiln can persist into the afterburner, although the degree of nonuniformity is substantially reduced compared to either the kiln or transition sections. High destruction and removal efficiencies were achieved under all operating conditions of these tests through a combination of kiln and secondary combustion processing.     

Assessment of human exposure to ambient particulate matter

Recent epidemiological studies have consistently shown that the acute mortality effects of high concentrations of ambient particulate matter (PM), documented in historic air pollution episodes, may also be occurring at the low to moderate concentrations of ambient PM found in modern urban areas. In London in December 1952, the unexpected deaths due to PM exposure could be identified and counted as integers by the coroners. In modern times, the PM-related deaths cannot be as readily identified, and they can only be inferred as fractional average daily increases in mortality rates using sophisticated statistical filtering and analyses of the air quality and mortality data. The causality of the relationship between exposure to ambient PM and acute mortality at these lower modern PM concentrations has been questioned because of a perception that there is little significant correlation in time between the ambient PM concentrations and measured personal exposure to PM from all sources (ambient PM plus indoor-generated PM). This article shows that the critical factor supporting the plausibility of a linear PM mortality relationship is the expected high correlation in time of people's exposure to PM of ambient origin with measured ambient PM concentrations, as used in the epidemiological time series studies. The presence of indoor and personal sources of PM masks this underlying relationship, leading to confusion in the scientific literature about the strong underlying temporal relationship between personal exposure to PM of ambient origin and ambient PM concentration. The authors show that the sources of PM of non-ambient origin operate independently of the ambient PM concentrations, so that the mortality effect of non-ambient PM, if any, must be independent of the effects of the ambient PM exposures.     

A new approach to assessment and management of the impact from medical liquid radioactive waste

The Swedish regulations concerning disposal of clinical radioactive waste are currently under revision and a graded approach is proposed for risk limitation purposes. To assist the revision procedures, a screening study was performed to estimate public exposures from liquid releases from hospitals to public sewers. The results showed that doses to sewage workers were above the dose constraint of 100muSva(-1) especially for (131)I and (99m)Tc. Hence, a dynamic model, LUCIA, was developed for realistic assessments in which radionuclide transportation in sewers was modelled. Probabilistic simulations were performed to obtain probability distributions of radionuclide concentrations in sludge. Concurrently, estimates of the effective doses to sewage workers decreased significantly and were below 10muSva(-1) except for (111)In and (131)I. However, the Kd-coefficients representing the partition of radioactivity between water and sludge in sewers are highly uncertain for (111)In. As shown by sensitivity studies, these values are the major determinant of the exposures in sewers.     

Measuring sustainability

An agricultural system is sustainable if productive output is maintained economically over time when assessed in relation to environmental concern. This paper considers ways of statistically evaluating measures of sustainability illustrated by reference to extensive data from the Classical Experiments at Rothamsted.     

Deposition and removal of fugitive dust in the arid southwestern United States: measurements and model results

This work was motivated by the need to better reconcile emission factors for fugitive dust with the amount of geologic material found on ambient filter samples. The deposition of particulate matter with aerodynamic diameter less than or equal to 10 microm (PM10), generated by travel over an unpaved road, over the first 100 m of transport downwind of the road was examined at Ft. Bliss, near El Paso, TX. The field conditions, typical for warm days in the arid southwestern United States, represented sparsely vegetated terrain under neutral to unstable atmospheric conditions. Emission fluxes of PM10 dust were obtained from towers downwind of the unpaved road at 7, 50, and 100 m. The horizontal flux measurements at the 7 m and 100 m towers indicated that PM10 deposition to the vegetation and ground was too small to measure. The data indicated, with 95% confidence, that the loss of PM10 between the source of emission at the unpaved road, represented by the 7 m tower, and a point 100 m downwind was less than 9.5%. A Gaussian model was used to simulate the plume. Values of the vertical standard deviation sigma(z) and the deposition velocity Vd were similar to the U.S. Environmental Protection Agency (EPA) ISC3 model. For the field conditions, the model predicted that removal of PM10 unpaved road dust by deposition over the distance between the point of emission and 100 m downwind would be less than 5%. However, the model results also indicated that particles larger than 10 microm (aerodynamic diameter) would deposit more appreciably. The model was consistent with changes observed in size distributions between 7 m and 100 m downwind, which were measured with optical particle counters. The Gaussian model predictions were also compared with another study conducted over rough terrain and stable atmospheric conditions. Under such conditions, measured PM10 removal rates over 95 m of downwind transport were reported to be between 86% and 89%, whereas the Gaussian model predicted only a 30% removal. One explanation for the large discrepancy between measurements and model results was the possibility that under the conditions of the study, the dust plume was comparable in vertical extent to the roughness elements, thereby violating one of the model assumptions. Results of the field study reported here and the previous work over rough terrain bound the extent of particle deposition expected to occur under most unpaved road emission scenarios.     

Chemical (polycyclic aromatic hydrocarbon and heavy metal) levels in contaminated stormwater and sediments from a motorway dry detention pond drainage system

Chemical (polycyclic aromatic hydrocarbon - PAH and heavy metal) levels in stormwater and sediment samples collected from the London Orbital (M25) motorway drainage dry detention pond at Oxted, Surrey, UK were determined. Such chemicals are derived from vehicular combustion products and the wear and tear materials deposited onto the motorway surface. Gas chromatography-mass spectrometry (GC-MS) was used for the qualitative and quantitative determination of 16 USEPA priority PAHs in motorway drainage sediments. The GC-MS method, incorporating a solid phase extraction step, provides detection limits ranging from 0.17 to 0.41 mg kg(-1)(dry weight). Almost all of the 16 USEPA listed PAHs were detected. Phenanthrene, fluoranthene, pyrene, benzo(a)anthracene, chrysene, benzo(b)fluoranthene, benzo(a)pyrene and benzo(g,h,i)perylene (PAH numbers 5, 7, 8, 9, 10, 11, 13 and 16) were among the PAHs found at "higher" levels (ranging from 0.3-10.2 mg kg(-1), dry weight) in the sediment samples. PAH levels show little change along the motorway drainage silt trap (facility for reducing the levels of suspended particulate matter in the stormwater). PAH concentrations are considerably higher in the dry detention pond outflow interceptor. Statistical analysis showed that significant correlation coefficients (based on a t-test at the 95% confidence interval) were obtained between those PAHs found at high concentrations over all of the sampling sites. Several PAHs were dispersed beyond the treatment facility and accumulation in the sediment of the deer park resulted in levels ranging from 0.3-1.6 mg kg(-1), dry weight. These PAHs found beyond the treatment facility (in the local farm deer park) may contribute a serious health threat to farm animals or even fish in the aquatic environment. Heavy metal levels (V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Mo, Cd, Sb and Pb) of the drainage stormwater and sediments were determined by inductively coupled plasma mass spectrometry (ICP-MS), with quality control evaluation using two certified reference materials. Typical detection limits were found to be below 0.1 [micro sign]g l(-1) for stormwater and 0.005 mg kg(-1) for acid digested sediments. Raised heavy metal levels were found throughout the dry detention pond facility and only decrease when the stormwater is diluted following discharge into the river Eden. Statistical analysis also confirms that some significant correlations exist between various heavy metals and PAHs. However, no overall conclusive trend is found indicating that a particular PAH is deposited in sediment relative to a specific heavy metal/s. These results raise some serious concerns about the dispersion and accumulation of chemicals in the sediments of motorway stormwater drainage systems and the need for maintenance and clean-up of contaminated material from such systems.     

Synthesis of environmental evidence: nitrogen dioxide epidemiology studies.

The use of meta-analysis is becoming more common in the medical literature, but it is not common in the environmental literature. Although meta-analysis cannot combine a group of poorly executed, conflicting studies to get an unequivocal answer, there are certain situations where it can be helpful. The inability of studies to produce similar results may be a function of the power of the studies rather than a reflection of their quality. The literature on the effects of nitrogen dioxide on the odds of respiratory illness in children is such an example. Three quantitative methods for the synthesis of this evidence are presented. Although the methods produce slightly different results, the conclusion from all three methods is that the increase in the odds of respiratory illness in children exposed to a long-term increase of 30 micrograms/m3 (comparable to the increase resulting from exposure to a gas stove) is about 20 percent. This estimated increase is not sensitive to the method of analysis.     

Ranked set sample design for environmental investigations

Ranked set sampling can provide an efficient basis for estimating parameters of environmental variables, particularly when sampling costs are intrinsically high. Various ranked set estimators are considered for the population mean and contrasted in terms of their efficiencies and useful- ness, with special concern for sample design considerations. Specifically, we consider the effects of the form of the underlying random variable, optimisation of efficiency and how to allocate sampling effort for best effect (e.g. one large sample or several smaller ones of the same total size). The various prospects are explored for two important positively skew random variables (lognormal and extreme value) and explicit results are given for these cases. Whilst it turns out that the best approach is to use the largest possible single sample and the optimal ranked set best linear estimator (ranked set BLUE), we find some interesting qualitatively different conclusions for the two skew distributions