Current status and research on E-waste issues in Asia

Rapid economic growth in Asia and the increasing transboundary movement of secondary resources will increasingly require both 3R endeavors (reduce, reuse, recycle) in each country and appropriate control of international material cycles. Recently, managing electrical and electronic waste (E-waste) has become an important target for domestic and international material cycles from the viewpoints of environmental preservation and resource utilization efficiency. To understand the current status of E-waste issues in the context of international material cycles and to discuss the future tasks related to achieving 3R in the region, we organized the National Institute for Environmental Studies (NIES) E-waste Workshop in December 2004. This article reviews past studies on E-waste and briefly describes the topics presented and discussions held at the workshop. The topics at the workshop included E-waste generation, recycling systems, international trade, and environmental impacts. In addition, we discussed various issues such as terminology, current environmental concerns, and possible solutions. Transboundary shipments of E-waste should be conducted taking into consideration the concept of sustainable development. The direction of future research and possible collaborations are also discussed.     

Comparison of end-of-life vehicle material flows for reuse,material recycling,and energy recovery between Japan and the European Union

Journal of Material Cycles and Waste Management - Japan and the European Union (EU) both have well-established End-of-Life Vehicle (ELV) policies and management systems. However, due to the...     

污泥投配率对污泥中温厌氧消化效果影响的试验研究

试验装置采用半连续流污泥中温厌氧消化反应器,污泥培养接近成熟后开始每天按不同污泥投配率加泥和排泥.结果表明:污泥投配率在3%～10%时,有机物分解率先增大后减小,去除率均在30%以上;污泥投配率在15%和20%时,污泥的有机物去除率非常小;污泥投配率在5%时,有机物分解率最大为41.2%;单位VSS产气量随污泥投配率的增大而呈先急剧上升后逐渐下降的趋势,当污泥投配率为5%时,单位VSS产气量为0.60 L/g,符合美国污水处理厂设计手册标准,其他污泥投配率下该指标均小于0.4 L/g.因此,认为实验用污泥中温消化的最佳污泥投配率为5%,这时污泥的可消化性较好.     

Liquefaction process for a hydrothermally treated waste mixture containing plastics

Most landfilled plastic waste is a mixture or is in the form of composites with incombustible wastes such as glass, metals, and ceramics. After hydrothermal treatment, including a steam-explosion process, the separation of mixed waste (MW) into organic and inorganic substances becomes easy. However, the effect of hydrothermal pretreatment on the subsequent liquefaction of organic substances from MW is not obvious. In this study, the effects on the liquefaction of polystyrene and high-density polyethylene are discussed. Moreover, optimum conditions for the liquefaction of organic substances from hydrothermally treated MW are identified. By means of this hydrothermal pretreatment, including the steam-explosion process, polystyrene and high-density polyethylene can be significantly converted to oil by liquefaction at 300°–400°C. In comparison with liquefaction of hydrothermally pretreated mixed waste (HMW) at 300°–400°C with a batch type reactor, the yield of oil increases significantly on liquefaction using a semi-batch type reactor. It is considered that the radical chain and termination reactions among the radicals from HMW were inhibited in the semi-batch type reactor. On liquefaction of HMW in a semi-batch reactor, the conversion of HMW to oil was enhanced on increasing the liquefaction temperature to 350°C and the holding time to 60 min. Chemical Feedstock Recycling & Other Innovative Recycling Techniques 6     

Characteristics of azaarenes and dioxins in gases emitted from waste incinerators

In this study, we propose an analytical method to determine the fourteen of azaarenes present in flue gas samples collected according to Japanese Industrial Standard K 0311, which designates the method for the determination of dioxins in flue gas. Azaarenes can be analyzed using the acidic water phase after shaking extraction with dichloromethane, which is unnecessary for dioxin analysis. Flue gas samples were obtained from 24 waste incinerators in Japan, and azaarenes were detected in all the flue gas samples (0.21–3800 μg/m³ _N). The most abundant of the detected compounds were quinoline and isoquinoline. The concentration of azaarenes had a tendency to increase with that of polychlorinated dibenzo-p-dioxins and dibenzofurans. The isomer distribution of heptachloro-dibenzofurans (HpCDFs) was calculated using the computed Gibbs energy of formation (ΔG _f ) obtained by the semiempirical molecular orbital method at various temperatures. The calculated isomer distribution was fitted to the measured value of HpCDFs. It seems that the temperature obtained from the fitting calculations is an indicator of the cooling capacity of the combustion gas in an incinerator. The computed ΔG _f also explained the measured isomer distributions of azaarenes. It is suggested that the isomer distribution of azaarenes in the combustion process is thermodynamically controlled. This work was presented in part at the International Conference on Combustion, Incineration/Pyrolysis, and Emission Control, 2006, Kyoto     

Japan’s waste management policies for dioxins and polychlorinated biphenyls

We summarize the measures taken by the Japanese government to prevent the emission of dioxins and polychlorinated biphenyls (PCBs) into the environment. Because incineration is the main method of waste management in Japan, reducing the amount of dioxins emitted from waste incinerators is an essential aspect of proper waste treatment. Intensive measures to prevent the formation of dioxins at the source have been implemented, with a focus on waste treatment methods and improving comprehensive management. The efforts have been very successful, with a 95% reduction in the amount of dioxins emitted between 1997 and 2003. The toxicity of PCBs has been monitored with keen interest since the Yusho incident. Unfortunately, treatment facilities for PCB wastes were not built until long after PCBs had been removed from use, and PCB wastes remained in storage in an untreated state. The Japanese government has promoted the construction of facilities for treating PCB wastes, and five such facilities have commenced operations. To more completely eradicate dioxins, a future challenge will be to reduce the amount of PCB-derived dioxins, which are persistent in the environment and have a long exposure pathway from the environment media to the organism and the human body.     

Effect of unburned carbon on lead, zinc, and copper recovery from molten fly ash by chloride-induced volatilization

The present work focuses on investigation of the effective recovery of heavy metals from molten fly ash by applying chloride-induced volatilization. In particular, the effect of unburned carbon on the chloride-induced volatilization of lead, zinc, and copper from model and real molten fly ashes was investigated in the temperature range 873–1173 K under a N₂ atmosphere. As a result, almost 100% of lead and a significant proportion of zinc were volatilized from the real molten fly ash samples at 1173 K. In contrast, for the model fly ash, volatilization ratios of lead and zinc at 1173 K were only 85% and 25%, respectively. Further, the results of X-ray diffraction analysis suggested that PbO in molten fly ash was converted either to Pb₂OCl₂ or Pb by respective chlorination and reduction reactions. Meanwhile ZnO and CuO in the molten fly ash were reduced to Zn and Cu by reaction with unburned carbon. Subsequently, Pb, Zn, and Pb₂OCl₂ were volatilized, but Cu remained in the solid residue. Finally, the volatilization ratio of zinc increased with the addition of carbon, and more than 98% of zinc was volatilized at 1173 K from a fly ash with a carbon content of 20%.     

Municipal solid waste composition and food loss reduction in Kyoto City

For 35 years, Kyoto City has conducted detailed household waste composition surveys under the guidance of Kyoto University by dividing household waste into approximately 400 categories. In addition, the city has conducted detailed composition surveys of commercial waste generated by businesses. These surveys show that food loss accounts for approximately 40% of total waste, of which leftovers and untouched food account for about 40% in both households and business facilities. Consequently, the annual generation of household and commercial food loss is estimated at about 30,000 tons. Various efforts have been made to reduce waste, including food loss, but further reduction in environmental burden is needed. Thus, Kyoto City revised the ordinance for waste reduction, and in March 2015, formulated a new municipal waste management plan. The plan not only includes the 2Rs (reduce, reuse), but also, for the first time in Japan, sets quantitative targets for reducing food loss. Kyoto City must ensure that the necessary waste reduction measures are clearly explained to the residents and business operators. To ensure that this plan is successful, it is important to clarify concrete actions that residents and business operators should implement, along with their effects.     

Greenhouse gas emissions from biogenic waste treatment: options and uncertainty

A simplified life cycle assessment was conducted to estimate greenhouse gas (GHG) emissions and energy production from each component of biogenic waste treated in an open dumping site, and by composting, anaerobic digestion, and incineration employed with additional options. The impact of uncertainties and sensitivities of the parameters in the treatment methods were investigated. We conducted a sensitivity analysis to identify the most sensitive parameters, and we discussed the relationship between uncertainty and sensitivity. Our results revealed that the moisture content of food waste and the biomass-derived carbon and methane concentration of the landfill gas of biogenic waste subjected to open dumping are the most sensitive parameters across all the treatment methods. The net GHG emissions from food waste treated in an open dumping site ranged over ten times (0.30 ? 3.67 Gg CO₂ eq/Gg). In addition, by employing additional options for the open dumping site, including soil cover, a landfill gas collection system, shifting to a semi-aerobic condition, and energy conservation by using a gas engine, we found that the net GHG emissions could be reduced by 10, 27.9, 37.4 %, and up to 56.7 %, respectively. Shifting to a semi-aerobic system is the most effective method for reducing GHG emissions, followed by landfill gas collection.     

Photodegradation of gaseous acetaldehyde and methylene blue in aqueous solution with titanium dioxide-loaded activated carbon fiber polymer materials and aquatic plant ecotoxicity tests

TiO₂-supported activated carbon felts (TiO₂–ACFTs) were prepared by dip coating of felts composed of activated carbon fibers (ACFs) with either polyester fibers (PS-A20) and/or a polyethylene pulp (PE-W15) in a TiO₂ aqueous suspension followed by calcination at 250 °C for 1 h. The as-prepared TiO₂–ACFTs with 29–35 wt.% TiO₂ were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and N₂ adsorption. The TiO₂–ACFT(PS-A20) samples with 0 and 29 wt.% TiO₂ were microporous with specific surface areas (S _BET) of 996 and 738 m²/g, respectively, whereas the TiO₂–ACFT(PE-W15) samples with 0 and 35 wt.% TiO₂ were mesoporous with S _BET of 826 and 586 m²/g, respectively. Adsorption and photocatalytic activity of the as-prepared samples were evaluated by measuring adsorption in the dark and photodegradation of gaseous acetaldehyde (AcH) and methylene blue (MB) in aqueous solution under UV light. The TiO₂ loading caused a considerable decrease in the S _BET and MB adsorption capacity along with an increase in MB photodegradation and AcH mineralization. Lemna minor was chosen as a representative aquatic plant for ecotoxicity tests measuring detoxification of water obtained from the MB photodegradation reaction with the TiO₂–ACFT samples under UV light.