最优环境税:庇古法则与税制协调

从经济学的角度对国外关于最优环境税的经典理论——庇古法则及近十年来研究的前沿内容——一般均衡模型等作出阐释，并在外部性理论的基础上通过一个一般均衡模型考察环境税的效率特性和在次优情形下最优环境税的决定因素。随后是对我国开征环境税的几点思考：环境税的课征范围应暂定为排放各种废水、废气（烟尘）和固体废弃物的行为。环境税税率的确定可以采用“反复迭代”的方法，即“环境效益优先，兼顾税收协调和收入分配等效应。”其他相关问题的处理，如环境税和其它政策手段的配合使用，环境税税收的使用等。     

MnO2/Al2O3催化剂-微气泡臭氧体系催化降解喹啉及其机理

制备了纳米MnO₂,并以Al₂O₃为载体制备了掺杂型MnO₂/Al₂O₃颗粒催化剂.催化剂焙烧温度和时间分别为500℃和4 h、MnO₂质量分数为8%时,催化剂具有最高的臭氧催化氧化活性.SEM分析表明,纳米MnO₂均匀分布于Al₂O₃载体表面.MnO₂/Al₂O₃催化剂的比表面积（BET）为183.22 m²·g^-1,平均孔容为0.27 cm³·g^-1,平均孔径为4.87 nm.建立了MnO₂/Al₂O₃催化剂-微气泡臭氧催化反应体系,研究了该体系对喹啉的降解去除效果及其机理.臭氧微气泡的平均粒径为61.7 μm.微气泡臭氧投量为30 mg·L^-1时,反应60 min后喹啉去除率能达到95%以上;反应20 min后,MnO₂/Al₂O₃催化剂-微气泡臭氧体系对实际煤化工废水二级出水的TOC去除率可达到55%以上.以叔丁醇作为分子探针,证明了羟基自由基（·OH）氧化作用在臭氧微气泡催化氧化体系中对喹啉的降解起到主导作用.     

亚氧化钛膜电极电化学特性及其处理印染工业废水的效能研究

电化学氧化法具有稳定高效、操作灵活、集成度高等特点,在处理难降解有机废水领域具有独特优势.电化学废水处理过程通常受限于传质速率,而膜电极有望解决这一瓶颈问题.亚氧化钛膜电极（TiSO-ME）的化学结构与电化学性质结果显示,经过高温还原法制备的TiSO-ME电极主要由Ti₄O₇和少量Ti₅O₉组成,大孔体积占总孔体积的92.7%,平均孔径为0.508 μm.电化学测试结果表明,TiSO-ME具有良好的导电性、高析氧电位和电化学稳定性.过滤试验结果表明,在0.82×10^-3~3.14×10^-3 mL·cm^-2·s^-1范围内膜通量与传质系数成正比.在电流密度为8 mA·cm^-2,膜通量为2.31×10^-3 mL·cm^-2·s^-1的条件下,电解1.5 h即可有效处理实际印染工业废水,sCOD去除率高达96.07%,电流效率可达24.22%,电能消耗较不存在膜通量时降低了32.99%.TiSO-ME能够实现废水在膜孔结构内部的穿流式操作,有效克服旁流式操作传质受限的问题,在小规模分散式工业废水处理中有着重要的研究价值和发展潜力.     

O3-BAC深度处理工艺中细菌群落时空分布及动态变化规律

为弄清饮用水O₃-BAC深度处理工艺过程中细菌群落的时空分布和动态变化规律,本研究以我国南方某O₃-BAC深度处理工艺水厂为研究对象,采用NovaSeq6000高通量测序技术对夏季和冬季各工艺单元出水及滤砂和活性炭生物膜等细菌群落进行解析.结果表明,出厂水pH、浊度、COD_Mn、菌落总数等指标均满足《生活饮用水卫生标准》（GB5749-2006）的要求.夏季细菌群落多样性明显高于冬季,活性炭生物膜的细菌群落多样性高于滤砂生物膜;混凝沉淀、臭氧化和消毒是影响细菌群落多样性的主要工艺单元.水样和生物膜样品绝对优势菌门均为变形菌门（Proteobacteria）,且主要菌门组成大体相同,但细菌群落门水平相对丰度存在一定的时空差异,属水平上差异则更为明显.此外,检测到的条件致病菌属主要包括芽孢杆菌属（Bacillus）、不动杆菌属（Acinetobacter）、假单胞菌属（Pseudomonas）和分支杆菌属（Mycobacterium）,且其所占核心微生物OTUs数目不受季节性影响.水温和生物可降解溶解性有机碳（BDOC）是显著影响细菌群落分布的主要水质参数.以上研究结果表明,O₃-BAC深度处理工艺过程中细菌群落具有时空变化特性,并可为饮用水微生物安全保障提供支撑.     

焚烧飞灰重金属含量及浸出长期变化规律研究

通过对24个飞灰样品的重金属全量消解和高精度X射线荧光光谱法（HDXRF）快速检测结果进行线性回归分析,发现HDXRF法可较准确测定飞灰中Cu、Pb、Zn、Ni和Cd含量（线性回归决定系数R²³0.90）.采用HDXRF法对某焚烧厂飞灰重金属含量6个月快速检测及浸出毒性测定数据统计分析发现：飞灰重金属月均含量较稳定（变异系数CV<0.14）但日均含量波动较大（CV>2.54）;飞灰中Pb、Cu和Zn含量呈正相关（相关系数r>0.78）;金属浸出浓度受浸出液终点pH值影响显著,超标频率依次为Pb（68.9%）、Cd（66.1%）、Ni（24.0%）、Cu（14.2%）和Zn（1.6%）.短期飞灰金属含量和浸出毒性数据受焚烧工况,烟气处理工况和垃圾组分等多种因素共同影响,不具有代表性.为评估垃圾分类源头削减重金属效果,建议采用快速检测方法对焚烧飞灰重金属含量进行长期监测.     

基于Stacking的地面PM2.5浓度估算

为了解决地面PM_2.5监测网络在空间和时间覆盖受限的问题,提出了基于宽时空覆盖的卫星气溶胶光学厚度AOD,利用Stacking方法建立地面PM_2.5浓度估算模型,将AOD、PM_2.5和各气象参数以及与PM_2.5排放有关的数据进行训练,使用改进网格搜索对模型超参数进行优化,通过对多重共线性分析,建立基于Stacking的最优PM_2.5浓度估算模型。选取2016-01-01-2016-12-31的数据作为实验对象,结果表明:相比于随机森林、GBRT和XGBoost 3种模型,使用岭回归作为元学习器的Stacking模型性能更优,可见Stacking适用于大范围地理区域的大气污染监测。     

雨水管道沉积物中典型无机氮的干期粒径分布

以南京江北新区分流制雨水管道沉积物为研究对象,考察不同粒径沉积物中铵态氮（NH₃-N）和硝态氮（NO₃^--N）干期分布特征,分析其随干期长度的变化关系,并探讨沉积物理化性质及微生物菌群结构对NH₃-N和NO₃^--N干期分布的影响.结果表明：粒径≤0.075mm的沉积物中NH₃-N占比最高（交通区30.8%,商业区36.7%）;交通区粒径≤0.075mm的沉积物中NO₃^--N占比最高（33.0%）,而商业区粒径0.075~0.15mm沉积物中NO₃^--N占比最高（34.4%）;干期长度与交通区0.075~0.15mm粒径段的沉积物中NO₃^--N含量及商业区粒径≥0.3mm的沉积物中NH₃-N含量之间的相关性均最显著;雨水管道沉积物中NH₃-N和NO₃^--N的干期分布与O-H和N-H等官能团、表面极性和亲水性、微观形貌等有一定关联;交通区雨水管道沉积物中Gemmobacter等反硝化优势菌种（相对丰度总和为20.15%）对NO₃^--N干期分布影响更显著.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.