四氟乙烯清洁生产工艺和污染控制

分析了传统空管裂解生产四氟乙烯工艺存在的污染问题 ,介绍了水蒸汽稀释裂解生产四氟乙烯工艺的污染控制情况。     

模拟医疗废物在管式电阻炉上的热解特性研究

在管式电阻炉上对由聚丙烯、面巾纸、纱布、医用脱脂棉、一次性口罩、医用乳胶手套等按一定比例组成的模拟医疗废物在氮气气氛进行了热解研究。重点探讨了10K／min，20K／min，30K／min和40K／min等不同升温速率对热解产物分布、产气特性和热解过程的影响。结果表明，随着温度升高，模拟废物的热解产生气体的主要成分逐渐由CO2和CO转变为C3H6、CH4、C2H6、C2H4和C3H8。同时，热解处理对模拟废物的减量化效果比较明显，固体残留率仅为5．61％～7．02％。而且，加热速率对模拟医疗废物热解过程的影响较大。     

煤热解过程中无机有害元素的变迁规律

在自行设计的加压密闭快速热解反应器中研究了神华和义马煤中Na、K、Pb和Mn等无机有害元素在氮气条件下随温度（300℃-700℃)的变化规律,进一步考察了热解气氛（氮气、氢气和二氧化碳）、压力对神华煤中这4种元素逸出规律的影响。结果表明：Na、K、Pb和Mn等元素在半焦中的残留量随温度的升高而减少,减少量随煤种而异,如在700℃时,神华煤中Na、K、Pb和Mn的析出率分别是义马煤的3、4．2、1．4和2．4倍;低压快速加氢热解有利于这4种元素的逸出。Pb是挥发性最强的元素,与热力学计算结果一致。     

生物燃气制气供气装置选型计算

根据生物质热解及其干燥所需能量计算,选择一种生物质燃气制气供气装置作为生物燃油生产过程中用于生物质干燥和热载体加热的能量来源,对降低生物燃油规模化生产能耗和生产成本具有重要的研究实践价值和经济意义.     

两种有机锌络合物处理棉花的霉变及热解行为研究

棉花是纺织业的重要原料,是人民群众生活不可或缺的必需品,同时也是我国进出口重要的商品。研究如何安全有效地进行棉花的储备具有十分重要的现实意义。棉纤维本身含有脂肪、蜡质和果胶等适合微生物生长繁殖的营养物质。在棉花储备中,高的回潮率会加速微生物的繁殖,进而产生热量。热量的累积会引起温度升高以及棉花霉变,不利于棉花的安全有效储存。因此,通过静电吸附法将安全无毒的有机锌络合物附着在棉纤维表面,研究表明,相同条件下,处理棉的霉变状况明显得到抑制。加速发霉条件下,未处理棉的相对于白纸的平均色差值为28.10,而双乙酸锌以及苯甲酸锌防霉处理棉的色差值分别为5.16和5.86,下降了81.6%和79.1%。自然发霉条件下,双乙酸锌以及苯甲酸锌防霉处理棉的色差值分别下降了53.8%和50.7%。同时研究了纯棉以及处理棉氮气下的热分解动力学,相比于未处理棉,双乙酸锌防霉处理后活化能下降了15.8%,而苯甲酸锌防霉处理后活化能下降了10.9%。此外,利用实时红外和热重红外联用技术得到了样品在热解过程中固相以及气相的裂解产物的红外谱图,发现防霉处理能一定程度上抑制棉花热解。     

活化温度对SCAC制备过程中副产物生成规律的影响

文章研究了污泥-玉米芯活性炭(SCAC)制备过程中,活化温度对副产物(热解气和热解油)生成规律的影响。热解气和热解油分别采用气相色谱仪和气质联用仪进行分析检测。试验结果表明,随着活化温度的升高,SCAC的产量逐渐降低,热解气与热解油的产量则随之增多。不同温度条件下,热解气的主要成分均为H2和CO2,热解气中H2所占的体积百分数随着活化温度的升高而增加,而CO2则相应降低。此外,热解气中CH4的含量也会随着活化温度的上升而略有提高,说明较高的活化温度更有利于热解气的资源利用。热解油组分较为复杂,每个温度条件下的液态产物都包括上百种化合物,可分为烷烃,烯烃,苯类,酚类,腈类,杂环化合物,多环芳烃,有机酸,酰胺,酯类,甾体,醇,酮以及其他类共14大类型,其中以有机酸、腈类和甾体类有机物含量居多。随着活化温度的升高,有机酸和多环芳烃的含量有所增加,而酚类化合物的含量则有所降低;当活化温度升高至650℃以上时,甾体类有机物含量明显降低。     

滇池蓝藻快速热解液化制取生物油的初步研究

文章采用实验室规模的固定床反应器作为实验平台,对蓝藻快速热解液化制取生物油的可行性进行了探讨,并对影响液化性能的诸多因素,如热解温度(300～700℃)、载气流量(0～400 mL/min)、原料粒径(d＜0.08 nn,0.15＜d＜0.25 mm,0.25＜d＜0.38 mm,0.38＜d＜3.35 mm,d＞3....     

Pyrolysis of rice husk and sawdust for liquid fuel

The paper is focused on studying how to convert rice husk and sawdust into liquid fuel. Rice husk, sawdust and their mixture were pyrolyzed at the temperature between 420℃ and 540℃, and the main product of liquid fuel was obtained. The experimental result showed that the yield of liquid fuel heavily depended on the kind of feedstock and pyrolysis temperature. In the experiments, the maximum liquid yields for rice husk, sawdust and their mixture were 56% at 465 ℃, 61% at 490℃ and 60% at 475℃ respectively. Analysis with GC-MS and other apparatus indicated that the liquid fuel is a complicated organic compound with low caloric value and can be directly used as fuel oil without any up-grading. As a crude oil, the liquid fuel can be refined to be vehicle oil.     

Effect of pyrolysis and oxidation characteristics on lauric acid and stearic acid dust explosion hazards

The effect of pyrolysis and oxidation characteristics on the explosion sensitivity and severity parameters, including the minimum ignition energy MIE, minimum ignition temperature MIT, minimum explosion concentration MEC, maximum explosion pressure P_max, maximum rate of pressure rise (dP/dt)_max and deflagration index K_st, of lauric acid and stearic acid dust clouds was experimentally investigated. A synchronous thermal analyser was used to test the particle thermal characteristics. The functional test apparatuses including the 1.2 L Hartmann-tube apparatus, modified Godbert-Greenwald furnace, and 20 L explosion apparatus were used to test the explosion parameters. The results indicated that the rapid and slow weight loss processes of lauric acid dust followed a one-dimensional diffusion model (D1 model) and a 1.5 order chemical reaction model (F1.5 model), respectively. In addition, the rapid and slow weight loss processes of stearic acid followed a 1.5 order chemical reaction model (F1.5 model) and a three-dimensional diffusion model (D3 model), respectively, and the corresponding average apparent activation energy E and pre-exponential factor A were larger than those of lauric acid. The stearic acid dust explosion had higher values of MIE and MIT, which were mainly dependent on the higher pyrolysis and oxidation temperatures and the larger apparent activation energy E determining the slower rate of chemical bond breakage during pyrolysis and oxidation. In contrast, the lauric acid dust explosion had a higher MEC related to a smaller pre-exponential factor A with a lower amount of released reaction heat and a lower heat release rate during pyrolysis and oxidation. Additionally, due to the competition regime of the higher oxidation reaction heat release and greater consumption of oxygen during explosion, the explosion pressure P_m of the stearic acid dust was larger in low concentration ranges and decayed to an even smaller pressure than with lauric acid when the concentration exceeded 500 g/m³. The rate of explosion pressure rise (dP/dt)_m of the stearic acid dust was always larger in the experimental concentration range. The stearic acid dust explosion possessed a higher P_max, (dP/dt)_max and K_st mainly because of a larger pre-exponential factor A related to more active sites participating in the pyrolysis and oxidation reaction. Consequently, the active chemical reaction occurred more violently, and the temperature and overpressure rose faster, indicating a higher explosion hazard class for stearic acid dust.     

城市生活垃圾热解产气特性的试验研究

在外热式固定床试验台上,针对城市生活垃圾中的典型组分,进行了不同条件下的热解试验研究。试验测量不同条件下产物的产气量和产气速率,分析了热解气的组分和气体热值。分析发现,物料的挥发分、加热方式以及热解终温等对产气影响大,随温度的增加产气中H2含量逐渐增多,C2H4和C2H6的含量逐渐下降,气体热值有一个最大值。