冷摆辗模具的材料选择及其热处理

模具寿命是冷摆辗的关键问题之一。选择合理的模具材料以及采用适宜的热处理工艺可以提高冷摆辗模具的强韧性,从而提高模具寿命。基于摆动辗压工艺的基本原理,分析研究了冷摆辗模具的受力情况,并对冷摆辗模具材料的选择及热处理工艺作了探讨。     

酸沉降破坏材料造成的经济损失的估算研究

酸沉降对材料的破坏和其经济损失估算是国际上酸沉降研究领域听一个重要课题，国内在经方面的研究较少，文章通过对“两广酸沉降破坏材料造成的经济损失的估算”研究，提出了了一套较实用的经济损失估算方法。     

The economics of tire remanufacturing

The world market for tires is described to identify the current material flow from raw materials to tires and the used tire disposal problem. Then, I describe the value-adding operations in the tire production process and in the tire retreading process. Once retreading is identified as the only recovery alternative that maximizes tire utilization, I explain why heat generation is the only recovery alternative, when retreading is not technically feasible. The economic values of heat generation in electric plants and in cement kilns are discussed. The paper culminates with the case of retreading, the tire remanufacturing process and the recommendation of a simple decision rule for selecting the number of times a tire should be retreaded to maximize its utilization.     

VEGETATION INFLUENCE ON SMALL STREAM SILTATION1

ABSTRACT: A meandering stream channel was simulated in the Hydraulics Laboratory at Colorado State University and a series of tests was conducted using four types of vegetation to evaluate the potential effects of vegetation on sediment deposition and retention in a stream channel. The data collected included average flow velocity, flow depth, length of vegetation, density of vegetation, cross-sectional area of the vegetative stem, wetted perimeter of the vegetative stem, and injection and flushing time. The findings indicated that the vegetation could retain from 30 to 70 percent of the deposited sediments. The ability of vegetation to entrap and retain sediment is related to the length and cross-sectional area of the vegetation. The variables describing the flow and the vegetative properties were combined to form a predictive parameter, the sedimentation factor (S_d) that can be compared with the amount of sediment entrapped by vegetation in a stream system. A relation was developed correlating vegetation length to sediment retention after flushing for flexibility and rigid vegetation.     

Current status and research on E-waste issues in Asia

Rapid economic growth in Asia and the increasing transboundary movement of secondary resources will increasingly require both 3R endeavors (reduce, reuse, recycle) in each country and appropriate control of international material cycles. Recently, managing electrical and electronic waste (E-waste) has become an important target for domestic and international material cycles from the viewpoints of environmental preservation and resource utilization efficiency. To understand the current status of E-waste issues in the context of international material cycles and to discuss the future tasks related to achieving 3R in the region, we organized the National Institute for Environmental Studies (NIES) E-waste Workshop in December 2004. This article reviews past studies on E-waste and briefly describes the topics presented and discussions held at the workshop. The topics at the workshop included E-waste generation, recycling systems, international trade, and environmental impacts. In addition, we discussed various issues such as terminology, current environmental concerns, and possible solutions. Transboundary shipments of E-waste should be conducted taking into consideration the concept of sustainable development. The direction of future research and possible collaborations are also discussed.     

Life cycle energy impacts of automotive liftgate inner

This paper compares the life cycle energy use of a cast-aluminum, rear liftgate inner and a conventional, stamped steel liftgate inner used in a minivan. Using the best available aggregate life cycle inventory data and a simple spreadsheet-level analysis, energy comparisons were made at both the single-vehicle and vehicle-fleet levels. Since the product manufacture and use are distributed over long periods of time that, in a fleet, are not simple linear combinations of single product life cycles. Thus, it is all the products in use over a period of time, rather than a single product, that are more appropriate for the life cycle analysis. Using a set of consistent data, analyses also examine sensitivity to the level of analysis and the assumptions to determine the most favorable materials with respect to life cycle energy benefits.As expected, life cycle energy impacts of aluminum are lower than steel at a single-vehicle level – energy savings are determined to be 1.8 GJ/vehicle. Most energy savings occur at the vehicle operation phase due to improved fuel economy from lightweighting. The energy benefits are realized only very close to the average vehicle life of 14 years. With the incremental growth of the vehicle fleet, it takes longer – about 21 years – for aluminum to achieve life cycle equivalence with steel. The number of years aluminum needs to achieve equivalence with steel was found to be quite sensitive to aluminum manufacturing energy and fuel economy. As the steel industry races to compete with other materials for automotive lightweighting, a systems approach, instead of part-to-part comparison, is more appropriate in the determination of viability of aluminum substitution from an energy perspective.     

SUMMER LOW FLOWS IN NEW ENGLAND DURING THE 20TH CENTURY1

ABSTRACT: High springtime river flows came earlier by one to two weeks in large parts of northern New England during the 20th Century. In this study it was hypothesized that late spring/early summer recessional flows and late summer/early fall low flows could also be occurring earlier. This could result in a longer period of low flow recession and a decrease in the magnitude of low flows. To test this hypothesis, variations over time in the magnitude and timing of low flows were analyzed. To help understand the relation between low flows and climatic variables in New England, low flows were correlated with air temperatures and precipitation. Analysis of data from 23 rural, unregulated rivers across New England indicated little evidence of consistent changes in the timing or magnitude of late summer/early fall low flows during the 20th Century. The interannual variability in the timing and magnitude of the low flows in northern New England was explained much more by the interannual variability in precipitation than by the interannual variability of air temperatures. The highest correlation between the magnitude of the low flows and air temperatures was with May through November temperatures (r =?0.37, p= 0.0017), while the highest correlation with precipitation was with July through August precipitation (r = 0.67, p > 0.0001).     

Sustainable pattern analysis of a publicly owned Material Recovery Facility in a fast-growing urban setting under uncertainty

Sustainable development goals are achievable through the installation of Material Recovery Facilities (MRFs) in certain solid waste management systems, especially those in rapidly expanding multi-district urban areas. MRFs are a cost-effective alternative when curbside recycling does not demonstrate long-term success. Previous capacity planning uses mixed integer programming optimization for the urban center of the city of San Antonio, Texas to establish that a publicly owned material recovery facility is preferable to a privatized facility. As a companion study, this analysis demonstrates that a MRF alleviates economic, political, and social pressures facing solid waste management under uncertainty. It explores the impact of uncertainty in decision alternatives in an urban environmental system. From this unique angle, waste generation, incidence of recyclables in the waste stream, routing distances, recycling participation, and other planning components are taken as intervals to expand upon previous deterministic integer-programming models. The information incorporated into the optimization objectives includes economic impacts for recycling income and cost components in waste management. The constraint set consists of mass balance, capacity limitation, recycling limitation, scale economy, conditionality, and relevant screening restrictions. Due to the fragmented data set, a grey integer programming modeling approach quantifies the consequences of inexact information as it propagates through the final solutions in the optimization process. The grey algorithm screens optimal shipping patterns and an ideal MRF location and capacity. Two case settings compare MRF selection policies where optimal solutions exemplify the value of grey programming in the context of integrated solid waste management.     

Material flow analysis of lubricating oil use in California

Petroleum lubricating oils, used throughout the economy, are distinct among petroleum products in their capacity to be recovered and recycled at the end of their useful life. Used lubricating oil is regulated at the state and federal level because of concerns about environmental impacts arising from improper disposal, although rates of recovery are not known. We present a material flow analysis of lubricants through California's economy in the years 2007–2012. We introduce a novel technique for computing aggregate waste generation from a collection of hazardous waste manifest records, and apply it in order to determine a recovery rate for used oil and to estimate the quantity of oil managed informally in the state. The records also offer a detailed view of the fate of used oils after they are recovered. We find that around 62% of lubricants are recoverable at end of life, of which 70–80% is being recovered. This rate shows a slight downward trend. If the trend is accurate, measures should be taken to improve the performance of the used oil management system. Policy opportunities exist to reduce the quantity of oil managed informally through improving access to responsible used oil management methods. These include increasing the collection of used oil from industrial sources as well as “do it yourself” oil changes, expanding in-state reprocessing capacity, and promoting increased out-of-state reprocessing of used oil. Our methods introduce new possibilities to make use of direct observation in material flow analysis, potentially improving data availability and quality and increasing the relevance of material flow methods in policy applications.     

Solvent design and inherent safety assessment of solvent alternatives for palm oil recovery

The concept of inherent safety is important in developing an inherently safer and user-friendly process. This paper discusses a new integrated approach of computer-aided product design and inherent safety assessment. Computer-aided Molecular Design (CAMD) approach was utilized in this work to identify potential alternative to n-hexane, the widely used industrial solvent in extracting residual palm oil from pressed palm fibre. The formulation of solvent mixtures was optimized to meet the targeted physical properties before being tested using the Soxhlet Extraction method. Inherent safety assessment to assess the solvent's flammability, toxicity, reactivity, and explosiveness was conducted on the new solvent mix, Mixture 1 (n-hexane + ethanol), Mixture 2 (n-hexane + acetone) and Mixture 3 (n-hexane + n-butanol). It was found that Mixture 1 and 3 are safer than n-hexane and able to extract more oil than n-hexane and Mixture 2. However, the utilization of the solvent is dependent on the end product from the residual palm oil.