石英灯辐射加热条件下低密度碳/酚醛复合材料高温响应及分析

目的研究低密度碳/酚醛复合材料在不同地面加热实验测试响应的差异性,指导材料在实际应用环境下的高温响应分析。方法对低密度碳/酚醛复合材料开展了热流为400 kW/m~2的单侧石英灯辐射加热实验,利用热电偶测温系统测量试件在加热过程中不同位置的温度时间历程,并对试件的烧蚀形貌和微观结构进行观测。同时与热流为464k W/m~2的氧乙炔加热陶瓷板辐射加热实验结果进行对比分析,并且采用有限元方法对材料的传热传质多场耦合计算进行分析。结果对于石英灯辐射加热,在测量点升温到接近200℃时,温度响应拐点都依次出现。由于加热的辐射热源不同,在不同的辐射波段下,多孔材料吸收和发射的热量不同,短时间内氧乙炔加热陶瓷板辐射加热使材料内部升温速率比石英灯辐射加热实验的要快,但长时间加热时现象刚好相反。结论进行传热传质多场耦合计算材料高温响应时,合理确定材料宏观性能随温度的变化至关重要。     

纤维增强气凝胶复合材料高温结构转变及热稳定性研究

目的研究高温受热条件下纳米复合隔热材料的结构转变特征及热稳定性。方法采用扫描电镜、X射线衍射仪、红外光谱仪及热重仪等检测方法。结果纤维增强气凝胶材料从室温到650℃存在连续的质量损失,从室温到放热前,质量损失为1.66%;365℃开始出现放热,温度升至398℃时达到峰值,整个放热过程对应质量损失约为1.3%;从435℃放热结束开始到650℃的质量损失为1.46%。经过400℃热处理后,试样比表面积从268m~2/g增加到437m~2/g;当试样热处理温度达到600℃时,试样的比表面积明显随之降低至198m~2/g。结论 SiO_2气凝胶复合材料以无定形结构为主,存在少量的二氧化钛晶体。在400℃左右,SiO_2气凝胶结构中硅甲基Si—CH_3发生氧化,产生明显的放热峰,之后硅羟基Si—OH之间发生缩聚反应,使600℃热处理后气凝胶中Si—O—Si网络骨架强度有所提高。未处理的纤维增强气凝胶材料试样上气凝胶纳米颗粒构成的块体较为良好地包裹在玻璃纤维表面,而经过600℃的高温热处理1 h后,块体气凝胶脱离了光滑的纤维表面,气凝胶纳米粒子发生收缩,致使材料比表面积下降。     

金属基复合材料及其超塑性技术的发展

颗粒或晶须增强铝基复合材料具有优良的性能。目前其制备工艺主要采用粉末冶金法和挤压铸造法。这类铝基复合材料已经有许多应用实例。铝基复合材料超塑性是近年来开发的新技术,可解决其成形性差的加工难题,扩大其应用领域。     

Synthesis of branched,nano channeled,ultrafine and nano carbon tubes from PET wastes using the arc discharge method

Upcycling polymer wastes into useful, and valuable carbon based materials, is a challenging process. We report a novel catalyst-free and solvent-free technique for the formation of nano channeled ultrafine carbon tubes (NCUFCTs) and multiwalled carbon nanotubes (MWCNTs) from polyethylene terephthalate (PET) wastes, using rotating cathode arc discharge technique. The soot obtain from the anode contains ultrafine and nano-sized solid carbon spheres (SCS) with a mean diameter of 221 nm and 100 nm, respectively, formed at the lower temperature region of the anode where the temperature is approximately 1700 °C. The carbon spheres are converted into long “Y” type branched and non-branched NCUFCTs and MWCNTs at higher temperature regions where the temperature is approximately 2600 °C, with mean diameters of 364 nm and 95 nm, respectively. Soot deposited on the cathode is composed of MWCNTs with a mean diameter of 20 nm and other nanoparticles. The tubular structures present in the anode are longer, bent and often coiled with lesser graphitization compared to the nanotubes in the soot on the cathode.     

供碳源载体及其在低碳氮比污水处理中的应用研究

为解决低C/N污水的脱氮问题,本实验自行研制开发了一种新型碳聚合物载体.对该载体进行低C/N污水的生物膜脱氮研究,考察了HRT、pH、DO、温度等因素对系统同步硝化反硝化脱氮效果的影响.结果表明:在C/N比为4、pH=8、DO=1 mg/L、HRT=6 h,T=24℃的条件下,氨氮及总氮的去除率分别可以达到90%和70...     

PAS-PDMDAAC复合混凝剂研究

以Al2（SO）4和PDMDAAC为原料进行了无机-有机复合絮凝剂的复合实验研制,确定其制备工艺条件,并对油田现场采集的钻井废水作絮凝沉降实验,所研制的PAS-PDMDAAC复合絮凝剂对COD的去除效率可大大提高.     

石墨烯基磁性复合材料吸附水中亚甲基蓝的研究

建立了一种超声辅助共沉淀法制备磁性Fe3O4/氧化石墨烯(Fe3O4/GO)纳米粒子.透射电镜和磁滞回线研究表明,该复合物具有小的颗粒尺寸和超顺磁性.该磁性纳米材料可以吸附废水中的染料亚甲基蓝,实验研究了溶液pH值、吸附剂的用量、时间和温度对亚甲基蓝去除率的影响.结果表明,pH值在6~9范围内,Fe3O4/GO都能高效地吸附亚甲基蓝.反应过程在前25 min反应速率很快,到180 min内达到吸附平衡.该磁性纳米材料对亚甲基蓝的吸附符合Langmuir吸附等温模型和准二级动力学方程,吸附过程是一个自发和吸热过程.该吸附材料对亚甲基蓝吸附容量高,在313 K时Fe3O4/GO的饱和吸附量为196.5 mg·g-1.另外,可以方便地通过外部磁场分离回收吸附剂,利用过氧化氢可以再生重复使用,是一种优良的吸附染料废水的材料.     

Sustainable method towards magnetic ordered mesoporous polymers for efficient Methylene Blue removal

The difficulty in achieving high removal efficiency for contaminants in textile wastewater over a wide range of pH impedes the progress of its treatment technique greatly. Herein, a facile and sustainable strategy was adopted for constructing magnetic ordered mesoporous polymers (M-OMPs) without the assistance of organic solvent and catalyst. The prepared M-OMPs were endowed with high special surface area and good superparamagnetism simultaneously, and exhibited high removal efficiency (>99%) for Methylene Blue (MB) within a short time (10 min) at a concentration of 50 mg/L. What's more, high removal efficiency was achieved over a wide range of pH 2-12 and the adsorption capacity for MB on M-OMPs was substantially retained even after 5 adsorption-desorption cycles, further demonstrating the application potential of M-OMPs in the decontamination of textile wastewater.     

废旧冰箱拆解聚氨酯泡沫塑料制备PU/PP复合材料

利用废旧冰箱拆解的聚氨酯泡沫塑料(PU)和聚丙烯(PP)、聚丙烯接枝马来酸酐(PP-g-MAH)为原料,采用物理化学回收技术制备PU/PP复合材料。用正交实验法分析PU填充量、PU粒径和PP-g-MAH 3个因素对PU/PP复合材料力学性能影响的显著性。结果表明,PU填充量对PU/PP复合材料拉伸性能有显著影响,对冲击性能和弯曲性能没有显著影响;在本文的实验范围内,PU粒径对PU/PP复合材料的力学性能影响不大;而PP-g-MAH投加量对PU/PP复合材料具有一定的影响。确定的优化工艺配方为:PU 40%;PU粒径选择2.00 mm;PP-g-MAH投加量10%。采用优化工艺制备的PU/PP复合材料的密度为1 042.88 kg/m3;冲击强度为2.9 kJ/m2;拉伸强度为10.30 MPa;拉伸模量为1 100 MPa;弯曲强度为18.5 MPa;弯曲模量为733 MPa。     

Processing and Properties of Mixtures of PHB-V with Post-consumer LDPE

Mixtures of poly-β-(hydroxybutyrate-co-valerate) PHB-V with virgin and post-consumer low density polyethylene (LDPE) were prepared by melt mixing in proportions of 100/0, 90/10, 80/20, 70/30 and 0/100 (wt/wt%). The mixtures were analysed by infrared spectroscopy, differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), melting flow index (MFI), tensile tests, scanning electron microscopy (SEM) and biodegradation in simulated soil. The DMTA and DSC curves of post-consumer LDPE suggested that this polymer was a mixture of LDPE and linear low density polyethylene (LLDPE). Virgin and post-consumer LDPE had lower MFI than PHB-V, but the blends showed higher index as the content of LDPE increased. The addition of LDPE reduced the tensile strength and Young’s modulus of the mixtures compared with PHB-V. SEM indicated poor interfacial adhesion between PHB-V and LDPE. PHB-V degraded slow and gradually, while both LDPE showed virtually no degradation under the conditions studied. The biodegradability of the blends depended on their composition and of the type of LDPE. LDPE improved the biodegradability of the mixtures.