Spatial cost efficiency in waste paper handling: the case of corrugated board in Sweden

This paper analyzes the spatial cost efficiency of the Swedish legislation regarding waste disposal handling. We focus on the case of corrugated board and recognize that the different counties in Sweden possess different economic prerequisites in terms of waste paper recovery and utilization potential. We employ data for six corrugated board mills and 20 counties and a non-linear programming model to identify the least cost strategy for reaching the politically specified recycling target of a 65% recovery rate for corrugated board. That is, the total costs of recovering a minimum of 65% in each county are calculated and compared with the case when the country as a whole recovers 65% of all old corrugated board is collected but there exist no uniform target for each county. The conclusion is that from an efficiency point of view the recovery efforts should be concentrated to the highly populated and urbanized counties, and not be uniformly divided throughout the country. In the base case, the results suggest that the cost efficient county-specific recovery rates should range from 51 to 72%.     

中国集成电路制造行业VOCs排放特征及控制对策

中国电子信息产业发展迅速,集成电路等电子器件产量不断增加.在集成电路制造的过程中,大量有机溶剂的使用导致VOCs的产生和排放,从而对大气环境造成影响.为掌握集成电路制造行业VOCs的排放特征,系统分析了其工艺流程和产排污环节,分析了行业废气收集和治理现状,通过对典型企业VOCs的排放监测,获得VOCs排放水平;采用排放因子法核算行业VOCs历史排放量,并基于行业排放特征及减排潜力分析,提出了相应的污染防治对策.结果表明：在集成电路制造中,VOCs排放环节主要集中在光刻、清洗、去胶等过程,1 m²集成电路产量约使用87 g有机溶剂,VOCs产生量较大;通过采取高效的VOCs治理技术,集成电路制造行业有组织排放水平较低,平均浓度为2.1 mg·m^-3,但厂界无组织排放浓度相对较高,平均浓度为0.78 mg·m^-3,接近国家标准的排放限值.根据排放量核算结果,2011—2016年中国集成电路制造行业VOCs排放量呈逐年上升的趋势,主要受产量增加而相应污染控制技术水平提升有限的影响,无组织排放量比重大,占排放总量的38.1%~45.1%.     

离子液体吸收废印刷线路板热拆解过程中挥发性有机物——基于COSMO-RS模型

模拟废印刷线路板（WPCB）的热拆解过程,分析热拆解过程中的挥发性有机物（VOCs）组分;利用真实溶剂似导体屏蔽（COSMO-RS）模型对浓度较高的污染物进行量子力学模拟,研究离子液体（ILs）组成单元对目标污染物溶解度的影响差异,分析溶解过程中主导分子间作用力类型,确定优选吸收剂;测定不同溶剂进行溶解性,验证模型适用性.结果表明：①乙酸乙酯和环戊酮是浓度较高的VOCs组分,在240和250℃时浓度分别为43.1,153mg/m³和105,252mg/m³,质量百分比总和分别为76.3%和67.3%.②高表面屏蔽电荷密度分布峰、长烷基链阴阳离子和亲电基团的存在可提高乙酸乙酯和环戊酮在ILs中的溶解度.双三氟甲磺酰基亚胺盐（NTf₂^-）类ILs是一类优良吸收剂.静电力和范德华力对溶解过程起主导作用.③COSMO-RS模型可定性和半定量用于预测乙酸乙酯和环戊酮的溶解度.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

低温等离子体协同催化降解废气污染物的研究进展

阐述了低温等离子体协同催化工艺流程与反应机理,探讨了反应温度、废气进口组分、废气中水蒸气含量、气体流速、气溶胶等因素对降解效果的影响。分析认为:一段式低温等离子体协同催化可改变低温等离子体特征及催化剂催化特性,但尚未解决尾气臭氧逃逸、副产物产生及放电稳定性等问题;两段式低温等离子体协同催化可提高污染物分子降解效率并减少尾气臭氧逃逸,但未能有效利用等离子体的能量,气体中的水蒸气、粉尘及反应过程中产生的气溶胶均能影响后置催化剂的催化性能;两段式低温等离子体协同催化已具备工程应用条件,还需配套高效预处理单元以降低废气中水蒸气、粉尘等对催化剂的影响。     

印制电路板海洋环境试验与实验室环境试验相关性研究

目的研究机载电子设备印制电路板西沙海洋大气环境与实验室环境试验的相关性。方法在西沙海域环境下开展两种印制电路板的棚下暴露试验,暴晒试验时间为3年,同时在实验室开展盐雾试验,分别通过测试绝缘电阻、品质因数研究两种试验环境的相关性。结果将以绝缘电阻、品质因数为基准相关性评价结果进行平均,得出印制电路板实验室加速试验和自然暴露试验存在着强相关。两种样品的加速系数分别是3.5,5.15。结论建立了印制电路板在西沙海洋环境试验和实验室盐雾环境试验的相关性,可为后续西沙环境试验的加速处理提供依据。     

消泡剂硅油I在工业废水氨氮测定中的应用

对色泽较深，含杂质量较高的废水加硅油I以抑制测定中蒸馏产生的泡沫．结果表明，在250ml水样中加硅油IO．10～1．25ml，即可收到理想效果．硅油I性质稳定，不随水蒸汽蒸出，对测定无干扰．     

泰州市环境空气中挥发性有机物分布特征

于2018年4—9月对泰州市环境空气中挥发性有机物(VOCs)组分开展现场观测,结合观测数据分析该市大气中VOCs的时空分布特征。结果表明:观测期间泰州市环境空气中VOCs平均摩尔比为45.1 nmol/mol,其中含氧挥发性有机物占比为57.8%;受周边排放源和地理位置影响,下风向点位的VOCs测定值高于其他点位;VOCs月均最高值出现在6月,与臭氧月均最高值出现时间一致,7—9月气团出现老化,导致臭氧生成能力减弱;观测期间VOCs中甲苯/苯(T/B)比值范围为0.201 9～5.130 3,且大部分T/B比值2,说明溶剂、油气和液化石油气挥发等排放源对泰州市环境空气中VOCs的影响较为显著。     

小型废电池填埋焚烧处置的健康风险分析

对废电池采取填埋、焚烧处置所引起的健康风险进行了分析，采用3种模型，分别研究了废电池随城市固体废物一起完全填埋处置，一起完全焚烧处置，一起部分填埋处置和部分焚烧处理时，可能引起的健康风险，由分析可知，镉镍电池焚烧过程将引起不可接受的致癌风险，填埋废电池也会引起重金属非致癌风险，提出在现阶段没有单独收集分类管理的条件下，对于小型废电池应采取填埋焚烧联合处置的办法，但应避免镉镍电池的焚烧，在建立了收集体系后，应该分类进行资源化和无害化管理。     

我国电子废弃物收集体系构想

解决中国电子废弃物问题,一是控制电子废弃物进入非正式循环利用者手中;二是把非正式循环利用系统纳入良好的电子废弃物管理系统,使之成为更有效和对环境友好的系统.因此,如何把千家万户废弃的电子废弃物有效收集起来,是关系到电子废弃物管理和循环利用的重要环节.在我国建立良好的电子废弃物收集体系,应以市场经济和目前我国“城乡二元经济“为基础,建立具有收集主体多元化、收集方式多样化,收集途径多渠道等特点的电子废弃物收集体系.