Catalytic degradation of toxic organic dye using an aluminum-doped Cu0.4Zn0.6-xAlxFe2O4 (x = 0.0, 0.2, 0.4, 0.6) spinel ferrite in a photo-Fenton system

Catalytic activity of spinel ferrite in breaking down toxic dye materials are promising due to their uniqueness. In this study, aluminum-doped copper zinc ferrite, Cu_0.4Zn_0.6-xAl_xFe₂O₄ (x = 0.0, 0.2, 0.4, 0.6), a catalyst for toxic dye degradation is synthesized through chemical co-precipitation route. The formation of the spinel ferrite catalyst is initially confirmed by Fourier transform infrared spectra, which shows the frequency of metal-oxygen bond vibration at 539 and 427 cm⁻¹ attributed to the tetrahedral and octahedral sites respectively. Higher intensity sharp peak of X-ray diffraction for (311) plane is the evidence for the phase purity and the formation of spinel ferrite. The crystallite size is found to decrease with the increase of Al³⁺ ion. The surface structure of the obtained particles is investigated using a scanning electron microscope. Analyses of the material's magnetic characteristics using a vibrating sample magnetometer (VSM) revealed that it is, in fact, a soft magnet, as evidenced by the loop of its hysteresis, which is narrow. The catalytic degradation of methylene blue dye under the mechanism of the photo-Fenton process is studied with the obtained spinel ferrites and the result is found to be as high as 96.5%. The process follows pseudo-second order kinetics and the Langmuir isotherm.     

Feasibility of honeycomb monolith supported sugar catalyst to produce biodiesel from palm fatty acid distillate (PFAD)

Carbon coated monolith was prepared by sucrose solution 65 wt.% via dip-coating method. Sulfonation of incomplete carbonized carbon coated monolith was carried out in order to synthesize solid acid catalyst. The textural structure characteristics of the solid acid catalyst demonstrated a low surface area and pore volume. Palm fatty acid distillate (PFAD), a by-product of palm oil refineries, was utilized as oil source in biodiesel production. The esterification reaction subjected to different reaction conditions was performed by using the sulfonated carbon coated monolith as heterogeneous catalyst. The sulfonation process had been performed by using vapour of concentrated H₂SO₄ that was much easier and efficient than liquid phase sulfonation. Total acidity value of carbon coated monolith was measured for unsulfonated sample (0.5 mmol/g) and sulfonated sample (4.2 mmol/g). The effect of methanol/oil ratio, catalyst amount and reaction time were examined. The maximum methyl ester content was 89% at the optimum condition, i.e. methanol/oil molar ratio (15:1), catalyst amount (2.5 wt.% with respect to PFAD), reaction time (240 min) and temperature 80 °C. The sugar catalyst supported on the honeycomb monolith showed comparable reactivity compared with the sugar catalyst powder. However, the catalyst reusability studies showed decrease in FFA% conversion from 95.3% to 68.8% after four cycles as well as the total acidity of catalyst dropped from the value 4.2 to 3.1 mmol/g during these cycles. This might be likely due to the leaching out of SO₃H group from the sulfonated carbon coated monolith surface. The leaching of active species reached a plateau state after fourth cycle.     

上海地区大气中氯化氢和颗粒氯排放源清单初步研究

氯自由基对于臭氧和二次气溶胶的生成贡献不容忽视.夜间颗粒相氯(Cl~-)可以通过与N_2O_5的复杂反应转化生成ClNO_2,其光解产生的氯自由基将显著影响大气污染的形成机制.本文以上海地区为案例,以2017年为基准年,收集了人为源活动水平数据,采用排放系数估算方法,首次建立了上海地区人为源氯化氢(HCl)和颗粒氯(Cl~-)的排放清单;并进一步结合模型计算海盐气溶胶排放的颗粒氯(Cl~-).结果表明,2017年上海市人为源和天然源排放的HCl和Cl~-分别为1207 t和820 t,其中,燃煤、工业、垃圾焚烧和秸秆燃烧产生的HCl排放量分别为327、134、722和24 t.燃煤源中的燃煤电厂和其它行业燃烧约占燃煤源排放的80%;工业源中水泥为HCl的最大排放源,约占工业源排放的51%;垃圾焚烧厂排放约占总HCl排放的60%,为最大的HCl排放源.燃煤、工业源、垃圾焚烧、秸秆焚烧、烹饪源和海盐的颗粒Cl~-排放量分别为82、153、498、47、39和0.6 t,燃煤源中的燃煤电厂占燃煤Cl~-排放的40%,供热、其他行业和家庭燃烧分别占燃煤Cl~-排放的24%、22%和14%;钢铁行业为工业源的主要Cl~-排放源,约占工业源排放的90%,垃圾焚烧厂占全部Cl~-排放的61%,烹饪源中餐饮企业为最主要排放源,占烹饪源的70%;天然源海盐的排放量极少,未占到总排放的1%.从空间分布来看,浦东新区、宝山、普陀、松江和金山排放的HCl和Cl~-占到全市人为源总排放的80%,为主要的HCl和Cl~-排放区域.本文研究建立的上海地区大气中氯化氢和颗粒氯排放源清单,对于深入研究氯化学机制对二次污染的影响提供了重要的数据参考.     

MnO2/Al2O3催化剂-微气泡臭氧体系催化降解喹啉及其机理

制备了纳米MnO₂,并以Al₂O₃为载体制备了掺杂型MnO₂/Al₂O₃颗粒催化剂.催化剂焙烧温度和时间分别为500℃和4 h、MnO₂质量分数为8%时,催化剂具有最高的臭氧催化氧化活性.SEM分析表明,纳米MnO₂均匀分布于Al₂O₃载体表面.MnO₂/Al₂O₃催化剂的比表面积（BET）为183.22 m²·g^-1,平均孔容为0.27 cm³·g^-1,平均孔径为4.87 nm.建立了MnO₂/Al₂O₃催化剂-微气泡臭氧催化反应体系,研究了该体系对喹啉的降解去除效果及其机理.臭氧微气泡的平均粒径为61.7 μm.微气泡臭氧投量为30 mg·L^-1时,反应60 min后喹啉去除率能达到95%以上;反应20 min后,MnO₂/Al₂O₃催化剂-微气泡臭氧体系对实际煤化工废水二级出水的TOC去除率可达到55%以上.以叔丁醇作为分子探针,证明了羟基自由基（·OH）氧化作用在臭氧微气泡催化氧化体系中对喹啉的降解起到主导作用.     

MnFe2O4磁性纳米棒非均相Fenton催化降解水中四环素的研究

采用水热合成法成功制备出MnFe₂O₄磁性纳米棒（s-MnFe₂O₄）,并考察了商品化的Fe₃O₄、MnFe₂O₄和合成的s-MnFe₂O₄纳米棒这3种磁性纳米颗粒作为非均相Fenton催化剂降解水中四环素抗生素的性能.同时,采用X射线衍射（XRD）、透射电镜（TEM）、N₂吸附-脱附、振动样品磁强计（VSM）及X射线光电子能谱（XPS）等技术对催化剂的理化性质进行了表征.非均相Fenton催化降解四环素的结果表明,s-MnFe₂O₄具有最高的催化活性,反应180 min,四环素的去除率可以达到87.6%,TOC的去除率达到47.5%.自由基捕获试验证实了羟基自由基（·OH）是非均相Fenton氧化过程中的主要活性物种.s-MnFe₂O₄磁性纳米棒的高催化活性归因于其表面拥有较高含量的Mn³⁺和Fe²⁺物种,它们的存在能加速界面电子的转移效率,从而促进·OH的生成.合成的s-MnFe₂O₄催化剂具有良好的稳定性,循环使用6次,四环素的去除率仅从87.6%降低到80.2%,且氧化过程中活性组分的流失很少.     

电场与MnxCey催化剂在苯氧化反应中的协同效应及机理探究

挥发性有机物（VOCs）大量排放已成为日益严重的环境问题,为了实现VOCs的高效去除,本文采用自蔓延燃烧合成法制备了一系列锰铈复合氧化物催化剂,将稳恒直流电场引入典型VOCs气体苯的催化氧化过程,并基于不同电场条件下催化剂的理化性质表征结果进行机理分析.实验结果表明,Mn_xCe_y催化剂对含苯废气的去除有良好的效果,稳恒直流电场显著促进了催化剂的活性,其中Mn₁Ce₃的催化性能最佳,电流为5 mA时,Mn₁Ce₃催化剂在155℃可达到50%的苯转化率,在202.4℃可达到90%的苯转化率,对应的转化温度T₅₀和T₉₀比传统方法分别降低了62.4℃和48.3℃,且电场中的反应活化能由52.32 kJ·mol^-1降低至32.31 kJ·mol^-1.根据实验现象及表征结果,发现协同效应与活性位点的快速持续再生及活性氧物种的转化有关,由此提出苯在Mn_xCe_y催化剂上的氧化机理及电场协同催化的反应模型.     

Density functional theory (DFT) studies of vanadium-titanium based selective catalytic reduction (SCR) catalysts

Based on density functional theory (DFT) and basic structure models, the chemical reactions on the surface of vanadium-titanium based selective catalytic reduction (SCR) denitrification catalysts were summarized. Reasonable structural models (non-periodic and periodic structural models) are the basis of density functional calculations. A periodic structure model was more appropriate to represent the catalyst surface, and its theoretical calculation results were more comparable with the experimental results than a non-periodic model. It is generally believed that the SCR mechanism where NH₃ and NO react to produce N₂ and H₂O follows an Eley-Rideal type mechanism. NH₂NO was found to be an important intermediate in the SCR reaction, with multiple production routes. Simultaneously, the effects of H₂O, SO₂ and metal on SCR catalysts were also summarized.     

Effects of calcination temperature on physicochemical property and activity of CuSO4/TiO2 ammonia-selective catalytic reduction catalysts

CuSO_4/TiO_2 catalysts with high catalytic activity and excellent resistant to SO_2 and H_2 O,were thought to be promising catalysts used in Selective catalytic reduction of nitrogen oxides by NH_3.The performance of catalysts is largely affected by calcination temperature.Here,effects of calcination temperature on physicochemical property and catalytic activity of CuSO_4/TiO_2 catalysts were investigated in depth.Catalyst samples calcined at different temperatures were prepared first and then physicochemical properties of the catalyst were characterized by N2 adsorption-desorption,X-ray diffraction,thermogravimetric analysis,Raman spectra,Fourier-transform infrared spectroscopy,X-ray photoelectron spectroscopy,temperature-pro grammed desorption of NH_3,temperature-programmed reduction of H_2 and in situ diffuse reflectance infrared Fourier transform spectroscopy.Results revealed that high calcination temperature had three main effects on the catalyst.First,sintering and anatase transform into rutile with increase of calcination temperature,causing a decrement of specific surface area.Second,decomposition of CuSO_4 under higher calcination temperature,resulting in disappears of Br(?)nsted acid sites(S-OH),which had an adverse effect on surface acidity.Third,CuO from the decomposition of CuSO_4 changed surface reducibility of the catalyst and favored the process of NH_3 oxidation to nitrogen oxides(NO_x).Thus,catalytic activity of the catalyst calcined under high temperatures(≥600℃) decreased largely.     

我国燃煤电厂大气汞控制技术综合评估与对策探讨

采用模糊综合评价法与层次分析法或专家判定法相结合,对我国燃煤电厂非常规污染物大气汞控制技术进行了综合评估,以筛选出最佳控制技术.建立了环境、经济和技术为一级指标的三层指标体系,共22个评价指标;初步筛选出洗选煤+烟气净化协同脱除技术、烟气净化协同脱除技术、烟气净化协同脱除技术+活性炭吸附技术等七项技术及技术组合并对其开展评估.结果表明:强调环境因素的层次分析法综合评估结果表明,超低排放协同脱除技术+活性炭吸附技术得分最高（0.797 0）,为最佳控制技术.而专家判定法与强调经济因素的层次分析法的综合评估结果一致,洗选煤+烟气净化协同脱除技术最具经济优势,是专家认可的最佳可用技术（BAT）和最佳环境实践（BEP）.研究显示,我国现阶段可采用洗选煤+超低排放协同脱除技术对燃煤电厂的大气汞污染进行控制,但为达到发达国家的严格排放标准,必须采用超低排放协同脱除技术+活性炭吸附技术.      

中国报废汽车中铂族金属回收潜力估算

基于Gompertz模型预测中国2018~2050年民用汽车的社会保有量;在此基础上,采用物质流分析方法估算得出我国汽车高峰报废年限大约为9a.然后,通过市场供给A模型预测我国2018~2025年汽车报废量,结果显示,我国汽车报废量到2025年将达到2535.05万辆,并且地理空间分布极不均衡.基于上述汽车报废量的时空分布,测算不同技术发展情景下废汽车三元催化剂中的铂族金属回收潜力和需求量.结果显示：如果按照当前催化剂消耗水平,全国铂族金属的需求量均在2019年达到峰值,铂钯铑分别达到4.57,65.70,7.92t,有望实现行业内闭环供应;如果以欧盟汽车尾气治理标准为目标,而现有汽车技术不发生根本变化,需求量将大幅增加,铂钯铑分别在2020年达到峰值85.01,109.38,8.37t,存在严重的供需矛盾.为此,建议在汽车生产者责任延伸制度中,关注废催化剂的回收和再生利用,以促进前端生产环节在不同技术选择中考虑稀贵金属的供给限制.